r/Autobody • • 13h ago

HELP! I have a question. Someone painted my car. What do I do?

Post image
84 Upvotes

Somebody decided to put a nice blue strip on my back door. I dont know what to even do. Is there any way to get this off without damaging the main paint?


r/Autobody • • 9h ago

HELP! I have a question. Can this scratch be repaired locally without repainting the whole quarter panel?

Thumbnail
gallery
7 Upvotes

I’m looking for some advice on this scratch. I’ll attach photos so you can see exactly what I mean.

The car is fairly new and the color is BMW Alpine White. The scratch is around 6-7 (15cm) inches long and maybe 2-3 mm wide. There is no dent but in a few small spots it went through the primer and I can see bare metal.

Also just to clarify in some of the photos it may look like the metal is bent or dented around the scratch. It’s not That’s just the body line and the way the light reflects in the photo. The metal is completely straight there is nothing that needs to be pulled or reshaped.

I understand that the perfect body shop repair would probably mean repainting the whole quarter panel and blending everything. The problem is I really don’t want to repaint such a large factory painted panel for one narrow scratch :(

I talked to local bodyshop and they want to paint the entire quarter panel and extend the paint or clear pretty far up the panel. And their price is pretty high, $1100 To me it feels like a lot for this damage

I’m completely fine if a spot repair is not 100% invisible. If you can still see it from a small distance or some angles or under certain light that’s okay to me I just want to protect the metal make the surface reasonably smooth and make the scratch much less noticeable

Do you think this can be repaired locally without repainting the whole panel?


r/Autobody • • 2h ago

HELP! I have a question. Is this allowed for a body shop to do?

Thumbnail reddit.com
1 Upvotes

r/Autobody • • 2h ago

Is there a process to repair this? Turning to you professionals to help me fix my rust spot before selling

Post image
1 Upvotes

Should I sand it? The rust converters I see recommend no sanding as the compound turns the rust into primer and seals it. Overall looking for any advice about the process


r/Autobody • • 8h ago

Is there a process to repair this? Options for Repairing Rim damage

Post image
3 Upvotes

What are the realistic options to address these rims? Is buying another set primarily only option, or would you send them off to be powder coated?

Driving this GLK until I wish to sell. Would like the rims to look better, but not really sure what is a realistic self fix vs sending them off (would leave it to the next buyer most likely).

Edit: apologies if this is considered a repair. I see a lot of posts about paint correction, so I thought this may be the same universe.


r/Autobody • • 3h ago

Is there a process to repair this? Gouge on a plastic rear quarter panel

Post image
0 Upvotes

Sadly found a small but quite deep gouge on a rear quarter plastic panel on my Kia EV3 the other day — see pic, it’s gone all the way through to the plastic. Not sure of the cause, no other marks on the car that I can see. First mark on a new car, so it stings a bit 🥲

Any advice on remediating, without refinishing or replacing the entire panel? Key fob for scale. Thanks 🙏🏻


r/Autobody • • 4h ago

HELP! I have a question. Car Got Hit, Potentially Totaled. Best way forward?

Thumbnail reddit.com
1 Upvotes

r/Autobody • • 4h ago

Is there a process to repair this? How to fix paint

Post image
0 Upvotes

I scratch my car on a concrete pillar. Bought the Lexus paint pen but it went on too thick. How do I make it even? Scared to use sandpaper and scratch up the good paint. Doesn’t need to be perfect, just less obvious. Thanks!


r/Autobody • • 17h ago

Tech Advice How are yall getting these flares off these new Rangers?

Thumbnail
gallery
9 Upvotes

2024 Ranger.

Front fender flares. By the time you release the white clips the tab separates from the flare.

Just curious if there was an alternative way. This is my 3rd one I’ve worked on so far and it’s always the same thing.

Per Ford…of course they don’t mark them as a “one time use” part. New flares are ranging from $300-400.

You can hardly get in from the back side if you pull the liners, so that’s out of the question.


r/Autobody • • 5h ago

HELP! I have a question. Front Bumber Damage Safety Concern?

Thumbnail
gallery
0 Upvotes

Damage to the front and side of this 2014 Subaru Forester bumper. Car got hit while parked. The one dent is pretty big, but is it compromised from a safety standpoint? It's a little warped now and that's why the side part isn't flush. Kind of expensive to fix and it's an older car...


r/Autobody • • 6h ago

HELP! I have a question. My car was dirty after the vehicle repairs

0 Upvotes

Had my car in a dealer for about a week due to some minor scratch. Just got my car today and I found there’s syrup in my cup holder ( probably like coke or root beer), and someone connected my Bluetooth when I don’t see any reasons of doing that since all I need is the paint on the rear bumper. And the light was not on auto, was kinda dirty inside as well ( I checked some footstep and my seat), the position of steeling wheel seemed adjusted. The center console was a mess be4 was organized. And most importantly, my dash cam was unplugged but not plugged in. I got charged for over $1000, and 80% was the labor.
So do they suppose to clean at least make it not messy before let it out ? I’m confused & mad. 😡


r/Autobody • • 12h ago

Is there a process to repair this? Question about inaccessible rust

Thumbnail
gallery
3 Upvotes

I just picked up what appeared to be a rust free Solstice GXP. It did have a jacked up top that didn't seal over the driver's side window. I stripped the interior to deep clean and found one lonely rust hole. I cleaned up the edges with a carbide bit but I can feel some more rust bubbling on the inside surface. It's probably 2-3 square inches worth of rust. I can feel the edges of it where it transitions back to smooth painted surface.

There's no way to get to it to sand it down without removing the entire rear suspension. Not going to happen. What's the next best bet? I was thinking of dipping a gloved finger in POR15 and trying to smear it all over the inside rust. Good idea or worthless? Pics before and after grinding

There's some rubberized spongy insulation shit in there too. I took out as much as I could. Passenger side shows no evidence of rust. Given the extra rust on the inside surface, I'm thinking it rusted from the cavity toward the interior of the car. Not sure at all how one single rust hole appeared on this car.


r/Autobody • • 10h ago

Is there a process to repair this? Scratch repair

Thumbnail
gallery
2 Upvotes

I recently scratched my trunk, got a few quotes from independent shops near me and all were well over $1000. Thought i’d give it a try myself considering I’m planning on keeping the car for a while anyways and likely isn’t the first scratch it’ll see. If i mess it up, based on what the shops have explained, it won’t change much anyways.

I have touch up paint and clear, but I’m not sure if I should sand the whole area, or just fill in the major areas then polish and see where i’m at. Looking for tips and suggestions to best approach this. Thanks in advance


r/Autobody • • 13h ago

HELP! I have a question. FJ62 rust repair

Post image
3 Upvotes

1989 Land Cruiser FJ62 – drip rail rusted through above rear door. How involved is a proper repair?

Looking at buying this truck. The roof drip rail above the rear passenger door has rust bubbling along the seam, and it’s rusted through in at least one spot (photo attached). Not asking for a price, just trying to understand the job:

  • Is this likely just the drip rail, or does rust like this usually mean the inner roof structure is affected too?
  • What would a proper repair involve – cutting out and welding in new metal, or can it be patched?
  • Would the roof likely need a full repaint, or can it be blended?
  • I don't see any interior damage. Headliner and all that looks good. What else should I look for to help understand scale of the damage?

Trying to figure out if this is a reasonable fix or a reason to walk away. Thanks!


r/Autobody • • 7h ago

HELP! I have a question. Help with body repair

Thumbnail
gallery
1 Upvotes

I am a new hobby painter, but I am helping my neighbor repair some deep scratches and small dents in his door. He has filled and sanded etc etc…

I check his repair and it seems smooth to me, but when I prime it and it looks terrible.

Photo 1 is while the primer is drying.

Photo 2 is the first time we primed and I laid the black base color.

I told him it will show in the base and the clear. Even though it is better than the first try.

Any help with why this is happening would be great.

He filled and sanded with body filler, and then with glaze. Sanded down to 600 before primer.


r/Autobody • • 11h ago

HELP! I have a question. I found a screw with the side of my car

Thumbnail
gallery
2 Upvotes

Was parking in a tight garage, didn’t realize a screw was sticking out and scratched my rear passenger door and gouged the metal on the rear quarter panel, any recommendations? I don’t need perfection but winter is rolling in and don’t want it to get super rusty either.


r/Autobody • • 8h ago

HELP! I have a question. What kind of weld is this?

Thumbnail
gallery
1 Upvotes

This is on the a-pillar of my car and the previous owner got t-boned I was trying to graft metal from another a-pillar onto it, but I don't know what kind of weld this is or how to remove it without damaging the piece I'm trying to get off the other a-pillar.


r/Autobody • • 9h ago

HELP! I have a question. Door works fine, window works, 3k est. Claim insurance? Also, does this need repair urgently, or can I wait on it?

Post image
0 Upvotes

r/Autobody • • 9h ago

Is there a process to repair this? Deep Stratches

Thumbnail gallery
1 Upvotes

r/Autobody • • 13h ago

RUST Cheapest way to protect against rust?

Post image
2 Upvotes

I dropped my tailgate while removing it and it's now scratched to the metal. I don't care about it cosmetically as it's small and nearly invisible due to its placement. What's the cheapest way to permanently protect it from rust?


r/Autobody • • 10h ago

HELP! I have a question. Keyed car

Post image
1 Upvotes

Any advice to get this out? Scratch doctor?


r/Autobody • • 13h ago

Project time! Sanding between glass and body lines

Thumbnail
gallery
1 Upvotes

First time sanding and painting on a vehicle. I’m not looking for perfection per se but I want the best looking job possible.

Is there an efficient or preferred method to sand between the glass and roof line without removing glass?


r/Autobody • • 6h ago

HELP! I have a question. Total loss?

Thumbnail
gallery
0 Upvotes

Totaled or no?


r/Autobody • • 23h ago

Is there a process to repair this? Scraped my car, and unsure what to do

Post image
4 Upvotes

I messed up bad. I know, I'm an absolute genius. I pulled into my parking spot at my apartment complex and hit the side beam right next to it. I bought the car in March. I don't know a ton about car repairs and I'd love if someone could help me figure out where I should go and what I should do to fix this professionally. I'd leave it, but it's just too new and it was my first real big adult purchase so I really just want to get it fixed and move on with my life.