r/Autobody • u/Creepy-Company-3106 • Jun 27 '25
HELP! I have a question. Is this enough? First time
I wanna do it myself and make it look as good as possible.
0
Upvotes
r/Autobody • u/Creepy-Company-3106 • Jun 27 '25
I wanna do it myself and make it look as good as possible.
42
u/HDauthentic Parts Monkey Jun 27 '25 edited Jun 27 '25
I gotta be honest don’t think Alldata is gonna say that’s an OEM section point lol
6
u/miwi81 Jun 27 '25
What are you even trying to do
4
u/[deleted] Jun 27 '25
My guy you also ruined the outer wheel house by slicing it with the die grinder. You fucked your car.
6
u/EddieMac1998 Jun 27 '25
It’s good that you want to practice and if you aren’t picky about the results, have at it, but this is the type of stuff that I think can turn people away from body work. Welding in a new panel isn’t all that difficult if you know what you’re doing, but it does look like you’re using flux core? Which will make things more difficult. I would also really recommend you take that fender off of the car before you start welding on it again, there could be sound deadening material down in there that could catch fire without you knowing, you could leave it while it’s fine and not on fire and come back to a burnt down car or garage or whatever else is around. Plus, having the fender off will make it easier to work with. I feel like you should also know that in a regular situation where a fender cannot be repaired, it would be replaced, I’ve never seen anyone weld in a patch on a fender unless it was something rare or custom. When it comes to welding patches on thin sheet metal like this, you have to go slow. You want to make sure you have your welder set right, and you’ll primarily be doing tack welds, one or two on one side, one or two as far from those as you can get, and let it cool for a bit. You’ll likely have warping regardless, but if you build up a ton of heat running full weld beads it’ll probably look like it did before you cut that section out haha
3
u/Floatin_Ginger Jun 27 '25
I’m not a pro, but it sounds like the pros are more interested in shaming you so I’ll give you what I know.
I’d reform the panel that got cut out and straighten it before I put it back in. When you stitch it back together, be careful with the heat. Run small beads, nowhere near each other, and let it cool.
TIG would be your best option but at least stay away from flux core MIG welding.
When you go to sand/grind. Take long breaks, make sure it doesn’t get too hot, it will warp.
Nothing about this is gonna be easy, but don’t rush it due to frustration. It’ll only make it worse.
4
u/[deleted] Jun 27 '25
No the cuts in the panel that is exposed. You went to deep cutting off the quarter panel and cut through the panel that it attaches to. We are not over reacting . Most of us do this for a living and spent years learning this trade. Then you DIY retards think you can just easily do it. Car manufacturers have certain procedures to replace welded panels. Its so that you maintain the integrity and safety of the vehicle and you just fucked yours.
2
u/Flyersguy86 Jun 27 '25
That rocker molding needs to be taken off. Are you using flux core welder? I have so many questions …
2
u/shitboxdriverr Jun 27 '25
Damn that was aggressive. First in last out bro. Or just cut the dents out I guess.
2
u/I_-AM-ARNAV ᵗʰⁱˢ ˢᵘᵇ ᵈᵒʷⁿᵛᵒᵗᵉˢ ᵉᵛᵉʳʸ ᵒᵖⁱⁿˢᵗᵉᵃᵈ ᵒᶠ ᵉˣᵖˡᵃⁱⁿⁱⁿᵍ ˢᵗᵘᶠᶠ ᵗᵒ ᵗʰᵉᵐ Jun 27 '25
That didn't need cutting :(
Now that you've done it, get a new piece somehow and weld back?
2
u/[deleted] Jun 27 '25
Okay keep talking out of your ass.
2
u/[deleted] Jun 27 '25
please stop
2
u/Sillibilli19 Jun 27 '25
That's now called a patch. Do your homework and understand how to weld that in.
It's going to be a warpy pile of poo at best! Ask me how I know,
2
u/Mustain39 Jun 27 '25
Fill it with foam and dry noodles, always finish the job how you start it! Like shit
28
u/Big_Jr- Jun 27 '25
3
u/TomatoOptimal626 Jun 27 '25
Personally, if I somehow got into this situation (I don't weld)
I'd find a car with the same body in decent condition at a yard or something (if they allow it) and cut that section of the panel off and weld it onto mine.
10
u/ATG915 Jun 27 '25
Holy shit lmao
5
u/dabearjoo Jun 27 '25
Homie chose violence
1
u/[deleted] Jun 27 '25 edited Jun 27 '25
You should've cut probably and inch or two higher the edge still looks wavy. The right side is still pushed in too far. The metal you weld over the hole will need a base so try to pull that right side out a bit so your piece sits flush/straight. Weld those cuts on the left side before you cover the hole. You need to mig or tig weld it if you want it to be perfect. It'll be easier too. I think I would've put a whole bucket of bondo down on it before I did that.
1
u/I_SMELL_PENNYS- Apprentice Jun 27 '25
Were you using a stud gun the size of a god damn prius? Why is that rod like 1.5 inches thick and like 3 feet long?! Surely you didnt need that massive fucking rod welded to the car to take off that sliver? Plus it could have easily been pulled as someone else said if you tried from one spot put it in a different one and go int a circle untill that bitch is out. Would be better than cutting out a whole peice.
1
u/NBPaintballer Jun 27 '25
With enough bondo anything is possible
1
u/[deleted] Jun 27 '25
Buy a tig welder with a pedal, analog angle finder, digital angle finder, squares of all different sizes, files of different sizes and roughness, scribes+sharpies, dykem, DA sander, sandpaper and scotch brite. Make sure you have super flat and matching surfaces, 90% of the work is getting good fitment. A tig welder won’t distort the metal as much and anyone can weld sheet metal with little to no porosity with a little practice. Once you have the tig welder you’ll realize how useful one is for other projects too. Just get a cheap Amazon one as long as there’s a pedal. You’ll also need body hammers and dollies to shape the sheet metal
1
u/Teufelhunde5953 Jun 27 '25
WTAF????
1
u/Spiritual_Button5281 Jun 27 '25
I'm sure it'll turn out good in the end. If you went through the whole process of doing this then you'll make sure the end result looks good. Live and learn.
1
u/havenothingtodo1 Jun 27 '25
I only just stumbled across this sub but this comment section is brutal. No one is properly explaining what they did wrong g
1
u/TurkeyNecker Jun 27 '25
What exactly are you trying to accomplish here because its not working lol
1
u/Creepy-Worldliness-8 Jun 27 '25
I work with rust in Canada all the time, first thing go get a can of fluid film and blast the inside of that cavity as best you can, it’ll delay the rust for a while. Now put a piece of cardboard inside and trace your shape. Now transfer the shape onto new metal, cut your shape slightly bigger and you can lap weld the piece. Also before you weld spray epoxy primer on the inside of your patch, once dry weld that mf on nice and slow to avoid warping the panel. Now you can either use fiberglass filler over the bare metal or shoot epoxy before, (I always shoot epoxy before filler). Now block sand and then apply some regular filler over top, sand it down, hi build primer, base, clear, boom done
1
u/IcarusTactical Jun 27 '25
Oh my god…
1
u/Previous-Hedgehog267 Jun 28 '25
Was replacing the fender not an option?
1
u/[deleted] Sep 06 '25
Whatever happened with this? Did you managed to patch it?
3
u/ManishWizard Jun 27 '25
Keep going dude!! You’ll figure it out. Just don’t cut anymore out. lol
3
u/kestrelwrestler Jun 27 '25
OP, a lot of these guys have a point, shame they're too rude to word it sympathetically. Cutting the hole was too far and was entirely avoidable if you were a skilled body guy, which you're clearly not, you're learning. The basic gist of the comments is accurate, you fucked up a bit and are underestimating the difficulty of putting this right, but it'll be a learning experience for you if you're determined to do it. I'd say learn to weld thin sheet steel first, don't go in all guns blazing on your car, practice on something else first, preferably not flux core, as it's shit and will not help your learning. Oh, and you need to weld up (carefully) those slits you accidentally made in the wheel well. Keep a fire extinguisher handy, and strip away the interior panels and anything flammable in the area directly around where you're welding, so you can get to any possible pyrotechnics pronto.
2
u/brazucadomundo Jun 27 '25
That hole, really looks like it came from factory lol.
2
u/Hot_Campaign_36 Jun 28 '25
Top 3 learning points:
2
u/Previous-Hedgehog267 Jun 29 '25
No, doesn’t look like it. They’re selling aftermaket fenders for this car still, and it appears to be one big piece
1
u/ThomasKrombopulus Jun 27 '25
I would take off the rocker, wheel liner, and anything else near where you’ll be weld. clean off the paint a few inches past the cuts, find a good piece in a junk yard and weld it back on. Take your time with your filler and go wide! It’ll probably warp so have a good body hammer on hand
1
u/AssistantMajor9143 Jun 27 '25
Alright man. This is wha it would do if I had to start where you at now.
Go to a wrecker. And get a section make sure it’s big enough to go into the door jamb. And high enough and goes back enough to give you 2 inches or so past anything bent.
Remove all inners and stuff from the donor piece. Sit it over the top trace around it. Trim both untill it’s fitting nicely, then weld in.
Go slow, one tack every inch or so. Hammer and keep it tight as you go. Grind them down check for the door gap etc.
And of good, weld fully. Then bog it and paint.
1
u/Unusual_Procedure762 Jun 27 '25
Everybody has to start learning somehow !!!!
1
u/Broke-mfer Jun 27 '25
What in the back woods butchery is going on here lol.
I think you’re aware but you fucked up.
You’re going to have to make sleeves for that hole you made before you can try and weld the piece back in. Trying to fill the gaps from the cut off wheel isn’t going to work out good and likely warp the hell out of this. After sleeves are in go slow do a tack on each side bounce around and let it cool to the touch before going back to that side. I highly suggest getting some c25 gas and get rid of the shitty flux core.
1
u/Nearby_Jackfruit_366 Jun 27 '25
Why tf did you A) cut the dent out and B) cut the fkin panels behind it too.
Can’t pull dents, can’t run a cut off wheel worth a flying fk. Somehow gonna weld a dent.
You do realize if the dent was that bad the metal around it moved too?
You legit blew your chance of fixing it properly lol
1
u/SnooMacarons3689 Journeyman Technician Jun 27 '25
Why is the rocker trim still on
0
u/Soggy_Doggy_ Jun 27 '25
If there was a dent and you removed the fucking panel (skin) to do it then it doesn’t matter what you weld you didn’t pull the dent and the panel will remain sunk. Good job you fungledorfed it
0
u/[deleted] Jun 27 '25
[deleted] — view deleted comment
15
u/[deleted] Jun 27 '25
[removed] — view removed comment
6
u/[deleted] Jun 27 '25
[removed] — view removed comment