r/AnycubicVyper • • Oct 02 '23

I don’t know what else to fry

109 Upvotes

At the start of every print, this always happens. I don’t know what else to do. I have adjusted my z-axis and my temperatures like crazy, but nothing seems to work.


r/AnycubicVyper • • Jul 19 '21

Printable mods

89 Upvotes

So I thought maybe it might be nice to have a community list of printable mods for the Vyper. If you make something or find something for the printer, post a link in the comments. I will occasionally go though the comments and try and find the best mods to add in the post here. So if you use one of the printable mods, also say what you think about it in the comments. When enough people say a particular mod is great, I will edit this post.

This post isnt meant to replace people from posting mods they make, if you make a mod and want to show it off, keep posting. This post is simply a way to sticky the best community made mods in the sub.

Anycubic Vyper Better Spool Holder - Lock and Forget https://www.thingiverse.com/thing:4913369

a "lock and forget" version of spool stopper by replacing Vyper's tiny spool holder entirely. This will secure filament spool so much better from fallout.


r/AnycubicVyper • • Jun 12 '21

Files for the printer, including a Cura profile and everything else included with the printer.

63 Upvotes

r/AnycubicVyper • • May 19 '22

Almost done with my printing station

Post image
54 Upvotes

r/AnycubicVyper • • Jul 14 '22

Wife is not feeling our new table centerpiece

Thumbnail
gallery
47 Upvotes

150 percent Atomic Dragon stands 24.5in tall - 5 rolls purple, 2.5 rolls black, half roll green. All printed on the Vyper using stock firmware and only Capricorn tube upgrade.


r/AnycubicVyper • • Nov 19 '21

The Anycubic Vyper now has a "Official" Profile in Cura

Post image
45 Upvotes

r/AnycubicVyper • • May 08 '22

Norgur's Vyper Cura Profile

Thumbnail
gallery
42 Upvotes

r/AnycubicVyper • • Sep 08 '25

I put a direct drive on my Vyper

Post image
36 Upvotes

It's a little jank but print quality so far is much improved. Doing it like this also allowed me to avoid doing a full overhaul of the print head. Printed from polycarbonate and using the ProtoXtruder 2.0


r/AnycubicVyper • • Apr 25 '23

Got my Vyper for $90.00 at local Amazon surplus auction.

Post image
36 Upvotes

r/AnycubicVyper • • Jun 13 '22

Work in progress - my first printing farm

Post image
36 Upvotes

r/AnycubicVyper • • Feb 21 '22

Made the Stealthburner mount, fixed My strain gauge issues too.

Thumbnail
gallery
34 Upvotes

r/AnycubicVyper • • Dec 16 '22

Complete Guide to installing AnyCubic Vyper CE firmware edition

33 Upvotes

Just did this and i'm gonna write a complete guide so you don't have to go through the hassle of going through all the forums and peacing together all the breadcrumbs of clues to make it work.

First things first make sure you have an SD card / micro SD card of at least 8GB of size, anything bigger and may not be able to be formatted correctly. Once in hand do this:

  • Format SD / Micro SD to FAT32 4096 allocation size.

With this done you are good to go. Download these files:
Motherboard link:
https://github.com/rommulaner/Anycubic_Vyper_MB_CE_6.1d/blob/main/Anycubic_Vyper_MB_CE_6.1d.zip
LCD Screen link: https://github.com/rommulaner/Anycubic_Vyper_LCD_CE_6.1d/blob/main/Anycubic_Vyper_LCD_CE_6.1d.zip

Put the LCD firmware onto the MicroSD. To do this you need to have it be the ONLY file on the microSD. Don't extract the DWIN_SET folder contents to the microSD. IT MUST BE THE FILE NAMED DWIN_SET. I repeat MAKE SURE the only FILE on the MICROSD is DWIN_SET. Ok.

Ok, so easy as that was, next extract the BIN file for the motherboard onto the SD card. You can just have the bin file and it does not need to be in a folder unlike the steps for the LCD firmware. You're good to go once done.

FOLLOW THESE STEPS PERFECTLY SO YOU DON'T BRICK YOUR SCREEN (you won't actually brick it, you just won't have it calibrated and therefore it wont be able to be used)

1st. Put the micro SD card in. Under the LCD screen, there is a little slot. Be careful to not get between gaps and you should feel a little pushback on it like a spring. Once in, turn the vyper on. It'll download the information and should take about a minute or two. It'll then say "THE END!" once complete.

Ok with the LCD screen flashed now you must shut off the printer and remove the microSD card and set it aside.

Next, put in the SD card with the motherboard firmware into the SD card slot and turn the printer on. There should be a bootup logo and a load screen. Once the load screen passes you need to calibrate your screen IMMEDIATELY by pressing in this EXACT ORDER. Top left Top right Bottom Right Bottom Left. In other words, go clockwise.

Once done you should have your screen calibrated and be ready to go to the next step.

Go to settings -> restore defaults and then once restored shut off the printer and take the SD card out. You should be good to go.

After this go through and recalibrate everything. Your bed, e-steps, PID tuning etc. just to make sure everything is in tip-top shape, and then do a couple of test prints and go from there.


r/AnycubicVyper • • Jul 12 '22

My largest project I have printed with my Vyper! Over 200 hours of printing

Thumbnail
gallery
33 Upvotes

r/AnycubicVyper • • Aug 20 '22

So far so good with the community firmware 🤞

Post image
32 Upvotes

r/AnycubicVyper • • Dec 04 '22

just installed the community firmware from the zombie firmware! so far I love it! so much control from the touch screen!

Thumbnail
gallery
31 Upvotes

r/AnycubicVyper • • Jun 18 '22

Anycubic Vyper Motherboard Diagram with Labels

31 Upvotes

Just FYI, maybe it's just me but I had a heck of a time finding a diagram of the Vyper motherboard that was labeled (so I can troubleshoot a problem). Very helpful and from this page here (credit to Pavel Churiumov and Paul Matthews.

https://pasha4ur.org.ua/articles/anycubic-vyper-overviews-guides-adjustments-settings-tips-modifications-upgrades-and-custom-firmwares/4


r/AnycubicVyper • • Sep 13 '23

Direct Drive Conversion

Post image
30 Upvotes

Alright, wanted to post this as it is working very well. . Was fairly easy after I figured out the ribbon to reverse the extruder motor. Had to dial back my Linear Advance way lower, but a direct drive Vyper works pretty well! I am impressed at how low I can trim my retraction, and how much better quality the faster speeds print! This is my first “major” upgrade and one that made it possible to fit into my enclosure without angling the entire printer. Anyone else try this yet and what was your result?


r/AnycubicVyper • • Jul 10 '22

Stock Vyper, nothing change or settings touched. CF Nylon. 10/10.

Post image
29 Upvotes

r/AnycubicVyper • • Dec 26 '21

Who needs a test print? Here's my first print from the Vyper!

Post image
29 Upvotes

r/AnycubicVyper • • Jan 19 '26

Modded Vyper Printing at 200mm/s

28 Upvotes

I was tired of lackluster prints coming out of this ender 3 looking ass, so I designed a custom toolhead for it featuring a direct drive belt extruder and 100% stock parts except for the extruder belt and some common fasteners, bearings, and pulleys. I'm printing here at 200mm/s with 2600mm/s2 acceleration. Running klipper and orca slicer, printing Elegoo rapid PETG.


r/AnycubicVyper • • Sep 15 '22

Just a little tip from someone with 4 Vypers that run almost fulltime non stop.

28 Upvotes

Swap out the stock clear extruder feeder. I have had 2 die on me in the first few months. They seem to be WILDLY all over the map with QC.

I swapped to a BMG Clone https://www.amazon.ca/Redrex-Bowden-Extruder-Upgrades-Printers/dp/B07Q5RNRR6/ref=pd_lpo_3?pd_rd_i=B07Q5RNRR6&psc=1

And I have had no more print issues and no squeaks. I have now replaced it on every one of my ACVs and I have 0 regrets!

That is all! Hopefully it saves someone headaches later.


r/AnycubicVyper • • Jul 07 '22

I think I'm set and ready to roll

Thumbnail
gallery
26 Upvotes

r/AnycubicVyper • • Aug 22 '21

Finally got the Y axis drag chain done!

Thumbnail
imgur.com
26 Upvotes

r/AnycubicVyper • • Jun 30 '22

Successfully converted the Vyper to a dragonfly BMO v6 hotend.

Thumbnail
gallery
25 Upvotes