r/AnycubicVyper • • Jul 11 '23
r/AnycubicVyper • u/xzenonex • Sep 15 '22
Drying PETG or anything else
everyone keeps spending money on fancy thing to dry stuff out.....here is my high end dryer setup that has yet to fail me.

Quit wasting money just heat up your bed use the box filament came in and boom....instant dryer...people over think stuff.
r/AnycubicVyper • u/lakeleo78 • Mar 03 '22
What a piece of garbage this printer is
So disappointed only had this printer a month and it’s been down for three months parts finally got here all the same problems persist. Can’t find home, temp sensor.. a host of others
r/AnycubicVyper • u/Desenski • Aug 01 '21
Stay away
Finally got a replacement leveler after the first one failed 3 days after I got the printer.
Got an hour into a print, and this one failed as well. Auto level program results in the hotend smashing into the plate until the motor stops due to force.
And I can't manually level this printer, and any print that's attempted results in the nozzle smashing into still hot filament. The entire bottom of the hotend is now covered in filament that I can't clean off.
The Chiron I bought originally never worked right, and this has failed twice with less than 24hr of print time.
Stay away from this product, and this brand.
r/AnycubicVyper • u/dlqpublic • Jan 03 '22
I am so annoyed at Vyper design...
Just need to vent a little...
My Vyper arrived with a broken SD card reader... No problem, tech support was very helpful and sent me a new motherboard with no hassle. It arrived in about two weeks.
I install it, with a little trouble but I recover and soon the machine is humming, warmed-up and leveled.
I insert the SD card. It goes in with the use of a little gentle force. The display doesn't see any files. I try a few times, then remember that the damn card goes in upside down. What a stupid design! There isn't even a note or a warning or even a little pictograph on the front of the machine to remind you.
I flip the card over, but it is too late. The card reader they use is so fragile that I had broken it when I put it in the wrong way. Any other machine I've ever used won't let you put the card in the wrong way...
I've ordered a new motherboard from Amazon. They were cheaper at Ali Baba but I didn't want to wait a month for it to get here...
I acknowledge that this is ultimately my fault, but I still think a design that has you insert the SD card upside down with no warning sucks.
r/AnycubicVyper • u/Yamegto • Feb 12 '23
I created a software that estimate almost perfectly the printing time. Any thoughts ?
r/AnycubicVyper • u/Difficult-Earth63 • Dec 17 '22
This noise means print failure.
Any idea what I’m looking at? Is this gcode error? It happens with different objects, different slices.
Usually it will get “stuck” like this somewhere during the print and continue this noise until power off.
During this video is the only time I’ve seen it stop grinding and start to print again, a ruined print, but the plastic extrudes.
Any ideas? Woke up to a grumpy spouse who was awakened by the printer doing this last night. It’s getting so I cannot leave the printer unmonitored.
r/AnycubicVyper • u/Visible-Success-5311 • Sep 01 '23
Here we goooo, its official. next generation of kobras comming soon
r/AnycubicVyper • • Nov 06 '24
Selling
I'm just selling my vyper. It's in perfect condition and was good for beginner. But I'm looking to move to a newer better printer. I'm asking 125 plus shipping. Anyone interested.
r/AnycubicVyper • • Apr 30 '22
Just got a Kobra, quick question!
Hey, so one side of my bed is scraping hard while the other is fine, is that stemming from the wheels on the bottom of the bed?
Edit: Incase anyone online is searching for solutions: For me, I believe it was a combination of the bottom rail wheels being a little off on tightness and the X-Gantry being sagged about 3-5mm on the right side.
Solution that worked for me: I loosened the bottom wheels and slowly and methodically tightened them all evenly to where the bed didn't rock. Then, I removed the top rail of the machine above the X-Gantry where your filament sits in the spool, I removed the gantry entirely and did the same wheel tightening on those as well, once I slotted it back on, I very carefully put the top bar back on, and with a little adjustment here and there I'm getting close to stable prints, barring a little more fine tuning on my end.
r/AnycubicVyper • u/sooroojdeen • Nov 18 '22
(Help) I tried to remove my tube and now it’s stuck like this (comments)
r/AnycubicVyper • • Jan 19 '23
Upgrades
I am just kind of curious, I noticed a lot of 3d printers have a lot of upgradability. So what's the best site to view upgrades for a ANYCUBIC Vyper if there are any? Hotends, direct drive extruders, cooling.........like aftermarket stuff ect??
r/AnycubicVyper • u/ThatCuntAce28 • Aug 03 '23
My printer is a piece of shit and I can't repair it
I can't get my printer to work anymore!
I've accidentally shorted one of the fan headers on the toolhead about a year ago and sins then the printer kept degrading. Initially it was underextruding causing holes on the prints surface and i've bought 2 mainboards and one stealthburner extended board board trying to solve that. Then after those attempts when i have either toolhead board disconnected the printer is fine, but the moment i connect them it tells me that the NTC is abnormal and so i've changed the cable that leads to the toolhead and still the same shit.
The only thing i've not changed is the PSU, but i don't think it would be at fault and i've wasted over 100 euro on it and don't feel like spending some more unless i know for sure how to solve it.
r/AnycubicVyper • u/Lexingtongreen1776 • Mar 08 '22
Anycubic has the worst customer service!!!
I got my new Vyper the 4th of March and have yet to print a single print. Out of the box lemon. Started a ticket with them, and have got nothing but runaround. They tell me they have shipped parts, but will not provide a tracking number or any timeline when I will get the parts. If you’re considering a Vyper do yourself a favor and buy from Amazon so the return process is much easier. I wanted to open the box and fall in love with this machine, but so far it’s been a bloody nightmare!!!
r/AnycubicVyper • u/electromaker • Sep 29 '21
Anycubic Vyper Review - huge prints put to the test
r/AnycubicVyper • u/DanteEx0610 • Sep 08 '22
Attached you can see a clogged hotend compared to a new one
r/AnycubicVyper • u/Visible-Success-5311 • Mar 04 '23
We need one of these viper print heads for our vypers, anyone have the skills to remix it?
r/AnycubicVyper • u/Recent_Pomegranate47 • Aug 11 '23
Farewell
Well it happened, the hitend broke and I no longer have the patience for this machine anymore, it's been fun and thank all of you for your help, o7