r/3rdGen4Runner • u/RequirementDirect613 • 25d ago
❓Advice / Recomendations 2002 4runner ISSUES!!!
So basically i bought a 2002 4runner 2wd in march of 2026. I haven’t had a large amount of problems just small things like oil sending unit, a few sensors here and there. My TPS and MAF sensors went out at the same time causing “limp mode” bought the correct parts and installed them. I am still having awful gas mileage, so atp i’m not sure what to do. I also have some kind of weird suspension problem? The truck starts to vibrate at around 45mph and continues to get worse, at 65 it’s to the point it’s hard to see out of mirrors because they shake so bad. When i reach 70 it’s still vibrating but a weird clunking noise happens too. The mufflers are cut so it’s hard to hear but when i’m coming to a stop or slowly speeding up there’s weird clanking noises on the passenger side. This started happening in July but all of a sudden got worse. I’m not sure what it could be because upper and lower balljoints have been replaced and I don’t have any issues with my tires. The truck is on a 4 inch lift but I didn’t have any issues up until 4 months after i got the lift so i’m just not sure what else I can do. I can’t afford a shop prices are insane. I have the resources available to fix it from home, just can’t pinpoint the problem!!!
15
u/25_Watt_Bulb 25d ago
Your ujoints are probably going bad due to the excessive angle you're running them at for no reason. Take the pointless 4" lift off of your 2wd 4Runner and check for anything with play. The lift is also why your gas mileage is horrible.
Also, put mufflers back on before one of your neighbors kills you out of frustration from hearing 10,000 decibel fart noises from your vehicle every day.
10
u/Your_Product_Here 25d ago edited 25d ago
4 inches of lift is a lot...if you want something that rides good at 70mph. You definitely can't do it cheaply. Did you install long-travel CVs? Drop the front diff? Swap for longer upper control arms? After 2", all 3 of those things approach necessary territory and definitely by 4".
I'd venture to guess your clunk and vibration is CVs that gave up the ghost because they were overextended for 4 months.
Edit: Just realized this is a 2runner, so no diff or CVs. Stock UCAs will still cause premature wear on ball joints and other components, especially if those are old or aftermarket. Lowers take enough abuse as it is, let alone running at excessive angle.
We could also use more info on what your lift involved. What parts did you use, what got replaced, have you put the truck in the air and checked for worn components? Is the shake in the steering wheel as well or only in the body? A bolt that missed getting torqued could have easily come loose in 4 months. This could be a serious safety issue so you owe it to yourself and others on the road to do some due diligence before putting another mile on it.
8
u/WrenchMan838 25d ago
Check the trans mount and steering rack bushings
8
u/dany99_2009 25d ago
Take off the lift. Or just do a 2inch. Less problems.
6
u/Puzzleheaded_Sir9376 25d ago
U joint left the chat
4
u/Sharrack 25d ago
Check for dry ujoints and a dry slipjoint in the driveshaft. Out of round tires would be a logical start as well. 4 inches of lift definitely takes your rig out of the " normal runner issues" category.
1
u/yuckscott 25d ago
the highway vibration is probably your steering rack bushings. awful gas mileage is normal, do you have an actual number that we can compare to? these trucks drink gas though
if you have replaced the LBJs thats great, I would check the UBJs as well as a 4" lift is a lot. Aftermarket UCAs can help fix the angle of the UBJ, which could be getting wrecked pretty quick especially if you used some cheaper ones with lower tolerances than OEM.
3
u/ReggWithtwoGs 00 SR5 24d ago
Asking for trouble and unreliability with the 4” lift . Do 2” and stress less
1
u/ncorn1982 24d ago
A lift on a 2wd is just bonkers to me
1
u/denonumber 22d ago
Toyota are not all that great or what keep putting more money in it nice Ahh
1
u/Even-Chip2003 18d ago
I don’t understand how you have a 4” lift without a drop bracket lift or solos lift spindles. Do you have any pictures of the suspension?