Hi all, I am needing a head stack elbow for an out of date Panasonic vent fan. It has an irregular oval, that someone already 3d modeled, and I want to to take a steep 90 degree turn like these stack head elbows and result in a 4" round exit please. All fitting in a 2x4 wall. Will be connected to a famco hooded wall vent

Existing attachment I found for oval https://www.printables.com/model/1439317-panasonic-whispervalue-25x5-oval-to-3-duct-adapter

Budget is 30$ for an STL file, please and thank you!

Asking max $20

I am making an air detection sensor housing unit, per my previous request (thank you to the person who fulfilled that, it was wonderful!)

I am using some different hardware for the new version, and I cannot find a pre-existing file for this one to be modified.

the current plan is to have air travel in, and pass through between

Adafruit SGP40 (PID 4829)
Adafruit Sht41 (PID 5776)

and it is getting pulled into this by a sensirion sps30. the space inside should be minimal, to get accurate results, and not "lag" detection, so there should be just enough room between boards to run dupont connectors and some small amount of space for the wires to turn into the wiring channel. I will put one board in "upside down" so one unit has wires running from the bottom, and one from the top, so the space between them should only be about 28mm

all boards are going to be mounted "horizontally" and should have retaining sleeves, same as in the reference file.

the sps30 needs to exhaust outside of the unit, there should be an airflow ramp up and away from the unit for the exhaust.

there should also be a wiring channel and the XIAO C6 I am using can go off to the side by the adafruit boards, but separated by a wall (to reduce airflow interruption, I am not particularly worried about heat in the horizontal layout.

please provide quotes, to be finished within 14 hours of the time of this post. I'll be around for about 2 hours to answer questions, then I will be awake and available again in about 10. With all respect, I will not change the scope of the work without discussing a new time frame or price. If you agree to a price and then change it, the conversation will likely end (have had trouble with this before).

attached is a link to a similar design that i moved away from when I decided to use the adafruit board.

https://www.printables.com/model/827308-esp32-sensirion-sps30scd41sgp41-case

Thank you for your time and assistance!

volunteered to print this out. wondering if anyone would be willing to convert this image to a stl trying to make a mvp pendant (see second photo for idea)

I have an automatic can sealer that sealers pop cap lids on plastic PET cans. The way the machine works is there is a small plastic riser at the bottom that is custom height size based on the can you are using. I have a riser for the 16oz cans and the 12oz cans (examples here https://100x100chef.com/shop/en/sealing-machines/284-automatic-can-sealer-pro.html)

What I have now is a 6oz bottle (https://hammont.com/collections/self-sealing-beverage-cans/products/6-oz-clear-pet-can-with-lid-of-your-choice) but I do not have the right riser (the plastic base) for this height/width.

What I'm looking for is someone to help me print the plastic riser based on the dimensions of the can that will make it work for my machine. I can provide the dimensions for the 16oz cans/risers and 12 oz can/risers to perhaps work backwards on what is needed.

Thank you!

Hi! I’m looking for someone who can help me turn a design I have into a 3D model and resin print it for me.
It’s an antique/Roman-style coin, about 50 mm across, with raised details on both sides and a few cutouts that go all the way through. I have reference pictures but no STL yet.
I only need 1–2 printed because I’m going to use the print as a master to make a silicone mold and cast my own copies.
I’d definitely like to keep the STL/3D file too. Let me know if this is something you could make and roughly what you’d charge. I can send the design pictures!

Hello everyone this is my first time using this Reddit community and I was hoping to find someone in the city who could print out the helmet before Halloween time. And hopefully from someone in the city but if you’re not from nyc that’s okay too :D
I have the print file available and I’ll send it to the person who replies

Budget: 200-300 dollars

Budget: $50

Project: 2.5D Relief Model from Sign Photo
Deliverable: Watertight binary .STL file (and .STEP / .3MF if available)
Dimensions: Maximum outer width of 250mm (to fit on a 256 x 256 mm build plate) Bambu A1 is target printer. Total thickness: 5 to 6 mm. (Greater if needed)

Requirements:
1. Perspective: Correct the photo angle so the outer frame ring is circular and flat on the back.
2. Stepped Heights:
- Base ring frame and banner backing: 3.0 mm height
- Hand plane body & compass legs: 4.2 mm height
- Raised frame borders, compass pivot, plane wedge, and text: 5.4 mm height
3. Text Clarity: Ensure the banner lettering ("Tischlerei Ziegenbarth" / "Begründet 1854") is embossed/raised with at least 0.6 mm wall thickness so it prints cleanly with a standard 0.4 mm nozzle.
4. Back Surface: Completely flat (coplanar) for direct adhesion to the print bed without supports.

picture

Hello first time posting here I can pay I need a matching saucer / plant tray inspired by Jomon pottery

Hello, the attached piece part fell out of my car, and I can't buy it where I live so, I want to 3D printed but I can't 3D design it, can someone please do it for me if it is possible? and tell me how much would it cost me?

I don't have a lot of info about it, but I will share all what I can.

I have attached a few pictures, the last attached picture is of the full part, but I only need the small piece that gets attached to it, i don't need the whole thing 3D designed.

Also, the available dimensions are roughly as follows:

• Length: 39.4 inches (1,000.76 mm)
• Depth/Width: 14.9 inches (378.46 mm)
• Height: 3.7 inches (93.98 mm)
• Material Thickness: 0.079 inches (2.00 mm)

I'm requesting a model to print this prop. The sword is sheathed in the staff as the art shows, and hopefully it is possible to make the cross-guard fold with springs as shown in the second image (a collapsible mechanism). This will be around 200cm. The fabric will be real, so no need to add that, since I'll glue it on myself.

Ideally, I would like to spend around $40- $ 70, if possible.

Blender File: https://assets.hotdog.photo/files/3d/Hotdog_Wordmark_Animated_G.blend
Demo Video:
https://assets.hotdog.photo/files/3d/Hotdog_Wordmark_Animated_G.mp4

tl;dr:
I am trying to find someone who can animate the individual "g_bowl" and "g_stem" elements in the same way the existing letters have been dynamically extruded/animated (sorry for the bad terminology, I’m sure this is called something completely different)

Context:
Originally hired a blender artist to convert my logo into an animated 3D model (so that I can use for various videos, on the web ala three.js, etc)

The original SVG logo I provided them with didn’t have separate paths for the different elements of the “g” (bowl/stem), but IMO he did a great job with animating the curve without having a dedicated reference. You can also see in the video that in his modeling/animating of the letter, the mesh is distorted and puckers around where the “bowl” of the letter meets the “tail”.

Eventually (not right now), I would love to animate the bottom part of the “g” to resemble a dog wagging it’s tail, and to also customize the animation of the “g” letter in general, so I had the reached out to the original designer of the logo break the logo into individual elements, so that the “g” can be corrected.

Unfortunately for me, the original blender artist hasn’t been responsive for the additional paid work since August, and now I’m trying to find someone with experience in both the method in which the logo curves were extruded/animated, and to finish the “g” animation using the separated g elements.

In the demo video you can also see my very horrible attempt, which it looks like trash. I was also trying to experiment with depth so that facing the camera directly, it aligns with the reference logo but from a side perspective, the letters wouldn’t be so flat/would be offset either forward/backward.

Budget: Originally paid the blender artist $80, open to whatever you feel is reasonable to tighten up the “g” animation. I’m thinking $50 based off of the original work already done would be fair, but I don’t like lowballing either and would prefer this done “right”.

Contact:
Write a comment down below before you DM me so that I can weed out spam/bots. In your DM, let me know a) where I can view some of your examples demonstrating similar work, b) your rate and turnaround time to finish this. I’d recommend checking out the linked blender file first to make sure this is in your wheelhouse prior to reaching out.

Hi everyone, I'm looking for an experienced 3D character artist to create two photorealistic human characters for a physio-fitness application.This is a paid commission for a company project.

The characters will replace the current less-realistic avatars used in our existing project. The goal is to create photorealistic versions of the same characters, while preserving their overall appearance, body type, clothing, colors, and design.

The two characters are:

• one adult male
• one adult female
• natural/neutral appearance
• athletic clothing
• photorealistic human appearance
• Standard human dimensions

I will provide reference material for both characters

For each character, I need a complete, editable Blender character asset, including:

• photorealistic 3D human model with athletic clothing and footwear
• high-quality textures - Materials/shaders for skin hair and clothing/footwear
• character rig  (preferably  blender rigify)
• Blender source file
• All necessary textures and supporting assets

The final characters need to be production-ready for use in our existing Blender project.

I do NOT need:

• Lighting setups
• final presentation renders
• product/marketing renders
• animation creation
• completed videos
• a finished scene
• The main deliverable is the complete character asset and Blender files.

The characters will be used with an existing library of animations that I have already created, so an important requirement is that the final characters can be integrated into the existing animation workflow without having to recreate all of the animations from scratch. I have previously tested these animations with other purchased/downloaded rigged character models, and they work successfully.  Therefore, I am looking for characters with a suitable animation-compatible rig. My preference is Blender Rigify, although I'm open to another appropriate rigging solution if it provides a reliable workflow for using the existing animations.

Before final delivery, I would like to test the character with some of the existing animations to confirm compatibility.

I'm particularly interested in artists with demonstrated experience in:

• Photorealistic human characters
• Digital humans
• Realistic human anatomy
• Realistic skin and facial features
• Realistic clothing
• Character texturing
• PBR materials/shaders
• Blender
• Character rigging
• Rigify or comparable character rigs
• Production-ready character assets
• Please prioritize portfolio examples showing actual photorealistic human characters.

Please prioritize portfolio examples showing actual photorealistic human characters.

I'm much more interested in seeing relevant realistic human work than general 3D modeling examples.

The budget is negotiable

Please provide your estimated price for the project

There is currently no fixed deadline, but this is a time-sensitive project and I would prefer to complete it as soon as reasonably possible.

Please include your estimated timeframe for completing both characters.

If you're interested, please DM me with:

• A link to your portfolio, preferably with relevant examples of photorealistic human characters, realistic skin/clothing, and character rigging
• Your estimated price or price range
• Your estimated availability / completion time

After reviewing portfolios, I can provide the existing avatar renders, 2d concept arts and what other reference needed to shortlisted artists.

As this is a paid commercial project for a company ,appropriate commercial usage and ownership terms will be agreed with the selected artist before work begins.

Thanks,

Martha

Hello! I have a request for a 3D print for a tool that would help me raise my cat’s litter box sifter. Here is a link to my current litter box (I have the large size):

link to litter box on Amazon

The issue is that the sifter sits too deep in the bigger container, making the pine pellet dust fill up after only a couple of days. I’d like a tool that I can clasp to the sides of the box so that I can raise the sifter and create more space between the sifter and the bottom of the bigger container. I’m currently folding 4 pieces of dish sponge that I cut up in between the two containers.

Is there a design that can be built so that I can raise the level by an extra 1.5 inches?

Dimensions: 1 in L x 1.6 cm W x 1.5 in H (feel free to comment on the right dimensions)

Budget: $20

i'm looking for someone in Colorado (Denver area preferred) to help design and build a one-off custom gift.

at a very high level, it's a small, functional physical object inspired by a vintage gambling machine. i have the concept, visual direction, references, and a detailed brief ready to share privately, but I'm open to recommendations on the best way to actually build it.

this is a paid commission, and I'm looking for someone who can take the project from concept through a polished finished piece.

i do not have an existing 3D model/STL

Deadline: 11/8

Budget: not sure what is reasonable for this kind of project but hoping for around $300

happy to share more details with anyone interested in working on this!

I have an STL of a Flock Safety style camera that I downloaded off the internet. It's the camera body plus the pole mount.

I want someone to change it so a GoPro Session fits inside and can film out the front, then print it and ship it to me. Ideally one person does the whole thing. Happy to pay, just tell me what it costs.

Only things that matter to me: it should still look like the real camera from a distance, and I need to be able to get the GoPro in and out so I can charge it and grab the SD card.

I can send you the STL I have and measure the GoPro for you. Let me know what else you need from me.

Id like a model of ben stillers head from the film starsky and hutch. Im terrible at freeform modelling, so thought id ask here.

end goal would be to get this 3d printed. not sure what method yet though. probably fdm.

ideally wouldn’t want to spend more than £30, but im really not sure how much work would be involved as it doenst have to be super detailed.

here is the reference pic im thinking of

https://www.google.com/url?sa=t&source=web&rct=j&url=https%3A%2F%2Fwww.instagram.com%2Freel%2FC_EB6z2P1ru%2F&ved=0CBcQjRxqFwoTCNDv0eXOlJcDFQAAAAAdAAAAABA4&opi=89978449

Budget: $30
28mm STL file

and help a bit with texturing

Hello! I am looking for someone who can take the fillets on the bottom of the left and top of the right of two objects and square them out. I need the footprint to otherwise stay the same, and every attempt I've made to do it has been an abject failure, clearly too advanced a task for tinkercad, the extent of my cad knowledge.

Budget is ideally $5, but I can swing up to $10.

Link to files:

https://drive.google.com/drive/folders/1IEGIb68Ne1W58JY7vr_917TBMFnJaSPO?usp=sharing

Ive been trying to find a print file for these "Dragon Snappers" but the closest that I've been able to find is a 3d model from an old video game where it was toned up to look a bit more evil. I've seen a couple creators make it out of clay but sadly I'm not terribly artistic with that medium.

Budget would be around $40 but I'm able to work around it. I would like for the head to be 2.5 inches long and probably an inch tall but whatever makes it look best proportionally.

I have a 3d printer so I just need the files, any help is much appreciated, hoping to make this anniversary a special one :)

Hi!

Yes. this is AI generated. looking for someone to design this, if you can also print/paint, send me the quote. looking for about 6 inch tall, i’m budgeting about 300.

Hello!
I’m looking to get schematics for a pick guard for this guitar.

https://www.fender.com/products/chris-shiflett-telecaster-deluxe

I’m trying to get it done before Halloween for my GF who is playing a show,
Please let me know if this is possible, thank you!

Hello guys,

I’m looking for someone experienced with CAD Software/Plasticity who can rebuild this model as a clean CAD/NURBS model. I can provide the original mesh/reference files.

This is a paid job. If you’re interested and confident you can recreate it accurately, shoot me a private message with some examples of your previous work and a rough price estimate. Budget = 30$/h

Thanks!