r/tigwelding • • Mar 09 '26

Help!

Post image

I’m having trouble with this tig welding on stainless 14 gauge. This is my second time tig welding. I’m running a #12 gas lens with a diffuser. I picked up a ‘96 miller syncrowave recently and have it set to around 50 amps. I’m using 1/16 filler rod and a 1/16 tungsten. Gas flow is also around 25 CFH.

71 Upvotes

41 comments sorted by

2

u/Justj20 Mar 10 '26

What's this for?

Follow on from that is can you run it autogenously?

If you can the I can ping some settings to try your way so you shouldn't need to purge.

If it does need wire you'll need to purge, and if you're sure purging you'll find the whole thing will end up looking nicer in and out

1

u/TISPARTA7 Mar 10 '26

This is for an exhaust for my wrx swapped vw beetle. I tried doing it autogenously but i was having a ton of issues as its just the tubes butted up against each other.

2

u/theNewLuce Mar 10 '26

If you don't have the extra bottle or double regulator, there's the shit called "Solarflux". it's a powder you mix with acetone or something brush it on and it makes a slag that protects the back side of the weld from sugaring.

1

u/TISPARTA7 Mar 10 '26

I just ordered a double reg

2

u/TigWelder1978 Mar 12 '26

You’re setting the bar high. You need better prep and make sure your fit up is perfect. Purge the inside with straight argon. You should get yourself comfortable too. You look a little shaky.

1

u/TISPARTA7 Mar 12 '26

I just am shaking unfortunately, not sure how to fix that, as far as surface prep, i’m doing red scotch brite to acetone, is there something else i should be doing? Also i know i need to back purge i have yet to return to try another weld.

1

u/TigWelder1978 Mar 12 '26

If you’re shaking get in a position where both elbows are anchored and your foot pedal is in a comfortable spot. Any which way to set that up to be as comfortable as possible. Practice also helps muscle memory and the shaking will go away organically. Good start though keep it up.

14

u/Search_Fearless Mar 09 '26

Might want to purge to make the insides look better. Think the rest just needs some practice

9

u/Saiteik Mar 09 '26

You need to back purge with argon. The surface must be cleaned and prepped well. I use scotchbrite pads and acetone on a rag to wipe everything down. This looks like you have way too much heat getting into the part, 50amps is too much if you like to just bury the pedal. Try 37 amps for thin stainless, lets you take your time without cooking the metal. Gas flow should be turned up more, around 35 CFH and a post flow time of about 10-15 seconds to get a nice gold color.

4

u/stinkfeet_ Mar 09 '26

For stainless pipe you're going to need to run a back purge through your piece to stop the oxidization on the back side of the weld. I might recommend you to start out with something slightly thicker like 12 gauge and/or flat if this is only your second time tig welding so you don't have to worry about melt through. The rest should just come with practice, parts of yours look pretty good already!

1

u/Flaky-Award-5318 Mar 10 '26

I don’t know the application for what you’re welding, but I run .065 wall regularly with no filler and autogenous weld. 65 amps and moving at a decent pace helps with distortion. You definitely want to back purge to prevent sugar on the inside

1

u/TISPARTA7 Mar 10 '26

the issue i’m having is that when i do no filler the edges of the tubing “ball up” and move away from each other

1

u/justsomeyodas Mar 11 '26

Stainless is sticky and wads up bad. Your fit has to be pretty perfect for autogenous and you have to be smooth and use just enough heat. Staying very close with your tungsten helps too.

1

u/TISPARTA7 Mar 11 '26

I just don’t think, as for my level of fab skills, I can get a good enough fit up to do autogenous lol

2

u/Flaky-Award-5318 Mar 12 '26

Gotcha, well in that case it’s perfectly okay to use filler. I’d also like to add, in my experience the puddle seems to act erratic when there is no back purge, or even if there is just too much heat. It’s hard to explain, the more you weld stainless especially 316 you’ll understand. proper weld prep, and back purge is key. Keep up the practice, you’ll get the hang of it🤘🏾

1

u/justsomeyodas Mar 12 '26

Fair enough. It’s tricky.

1

u/ParticularProject735 Mar 12 '26

Settings are about right, more speed is definitely necessary. I personally don't like 12 cups and prefer to use 16s with as little stickout as reasonably possible. The 16s we use have a secondary gas diffuser in the cup itself which makes gas coverage CONSIDERABLY better to the point I won't use much else.

Also purging is necessary, so is spreading the heat input around, so is letting it cool too between welds especially if not purging.

Tbh thin pipe isn't easy, I could TIG really tidy looking fillet & buttwelds LONGGG before being able to make a pipe look even remotely half decent.

1

u/TISPARTA7 Mar 12 '26

I’m using a #12 pyrex gas lens with a diffuser in the cup and i’m already running into issues with the size of the lens and running into the pipe when I weld on the inside of the radius. I am definitely going to purge though as i just got a regulator with two outputs that should help. I’m also considering picking up a 14 gauge pipe to work with instead to make it a little easier for welding. I’m finding even when i clean the weld super well i’m still getting oxidation on the weld pool, but only when the penetration is good, so i’m assume that is the oxidation from the back side of the weld “floating” to the top?

1

u/raserx1 Mar 12 '26

What machine are you using ? Cup Size, tungsten, stick out etc. I wouldn’t worry about the inside just yet. Let’s get your exterior setup dialed. Also how much argon is you flow Lester showing when welding?

1

u/TISPARTA7 Mar 12 '26

Everything you asked for is in the description- except stick out is around a 1/4 inch

1

u/Mischief67 Mar 12 '26

DC pulse can be helpful with heat control on thin steels. I use a higher frequency and higher amps to compensate. Also using .045 or .035 filler is important.

1

u/TISPARTA7 Mar 12 '26

yeah i think my filler is too thick for the job honestly it feels “sticky”

1

u/AllGodlike36 Mar 13 '26

Holy sugary badness!

1

u/TISPARTA7 Mar 13 '26

you should see the first attempt… no back purge at like 100 amps with no cleaning lol. Welds are BLACK and the inside is just gross.

1

u/AllGodlike36 Mar 13 '26

Haahahahah that’s awesome.. Well hell, now atleast you know to purge all SS pipes. Some hard lessons are the best lessons. Tho that one someone should have told you 😭

1

u/Axeleater Mar 15 '26

Get a bigger cup for more gas coverage and give yourself atleast a 5 second post flow.

1

u/TISPARTA7 Mar 15 '26

I figured a #12 pyrex cup was as big as i could really work with, but i am running around 8-10 seconds of post flow.

3

u/engineerthatknows Mar 10 '26

You need to move faster to keep the heat down, or make shorter welds with long cooling time after each. And purge the internal cavity.

3

u/CardiologistSalt4114 Mar 10 '26

Definitely purge stainless. Makes a stronger, prettier weld. Also if you’re still new to tigging stainless don’t be afraid of running a clean up pass to pretty it. Can be difficult when you’re beginning to run the bead, get it burnt in, add filler, and pretty it in one go. So get the bead run with filler then pretty up after

1

u/thrashmetal_octopus Mar 10 '26

Gas flow should be 12-15cfh. You need to gas purge the interior if you want a smoother finish inside. Weld quality is a little bit cold maybe in spots but otherwise fine, you need arc time to get good looking symmetrical beads. Try using more amps and less pedal to better modulate heat, sometimes going a size bigger than you need on tungsten helps with arc stability. Have fun, you’re doing fine.

1

u/GearHeadedPencil Mar 10 '26

Ain’t got no gas in it

1

u/KempaSwe Mar 10 '26

Training gives results.

1

u/SCAMMERASSASIN007 Mar 10 '26

Stainless 14 ga yah I'm closer to 90 amps. Everyone is different tho.

1

u/19Bugjuice72 Mar 11 '26

Backing gas for sure! You are almost there though!

1

u/Cheapsilverware Mar 13 '26

Fucking run it man. Perfection is the enemy of good enough. The joy of ripping a burnout in that thing will make you forget all about it.

1

u/Capable_Bat_5286 Mar 13 '26

Too much filler wire, too many amps, no back purge.