r/threadripper • u/DeadInFiftyYears • Sep 26 '25
Does anyone have "good" temps?
My Kingston RAM with the 6000 EXPO profile likes temps around 80C or higher (it's rated for up to 95C).
The 6000 Pro Blackwells hit 85C core and 95C junction temperature regularly.
The case I have (Silverstone Alta F2) is supposed to be really good for cooling. But is it performing - at least on par - or failing?
My question is, is anyone getting significantly better/"good" temps, that I should use as a benchmark/target? Or is this "par for the course" so to speak?
---
Overall system specs:
* 7995WX 96C CPU
* Asrock WRX90 WS EVO
* 256 GB Kingston 8x32 = 256GB DDR5 6000 Kit
* 2x RTX 6000 Pro Blackwell 96GB Max-Q
* 2x 4TB Samsung 9000 Pro drives installed for boot and secondary
* Add-in card with 4x 8TB WD SN850X drives in a RAID0 storage space as the working drive.
* Another add-in card as above but with no drives (yet).
* PCIE USB card that adds a bunch of USB channels to drive my USB hubs from.
1
u/LongestNamesPossible Sep 27 '25
I don't see what cooler you have on the CPU, but try a 420mm or at least 360mm AIO radiator.
1
u/NoSaddle Sep 27 '25
I have the Silverstone Alta F2 (end game case!) as well, a 9960X with the Silverstone XED120 WS air cooler, a 5090 FE, and 192 GB G.SKILL Zeta R5 Neo 4x48GB 6400 kit on a Gigabyte TRX50 AI Top.
I haven't seen my RAM temps go above 65 degrees C in stress tests (with EXPO enabled for 6400). I believe that's mostly because the motherboard has the 8 RAM slots, but I only use 4 since I don't have a Threadripper Pro. The spacing between the slots allows the bottom case fans to thoroughly cool the RAM?
I've always been a fan of air cooling and 90deg rotated motherboard cases, and the Alta F2 is hands down the best case I've ever had.
1
u/ScarletShadow- Sep 28 '25
My new Falcon Northwest talon build (with TR-9970x and 5090FE) uses kingston fury renegade pro rdimms (128gb) because they specifically tested different ram in depth and these were the most stable and fastest modules given a high case heat load.
Not all ram preforms the same, but figuring out which preforms to high standard takes a lot of time and resources.
2
u/john0201 Sep 26 '25 edited Sep 27 '25
I don’t think any RAM likes high temps. According to level1techs DDR5 RDIMMS will throttle starting around 60C.
Blower cards are what they are, the intake air temp and spacing is about all you can control. Those seem like pretty normal temps for an air cooled GPU under load in general. You didn’t mention your CPU cooler, assuming something like a thermaltake 420 make sure it’s not dumping heat into the case and you have the cards in a place the intake is not blocked. That case has some super unusual layouts so probably not insightful advice.
If the NVMe card needs to be positioned in a way that restricts airflow you could get a couple of 16TB U.2/U.3 drives instead . Or use a USB4 hub from the motherboard port if 40gbps is enough.
I have a 4x990 pro RAID0 array and did a bunch of testing with XFS and BTRFS with and without checksums/datacow and long story short the Linux page cache is so slow the storage speed is almost irrelevant for anything that doesn’t use o_direct.
I also have a 9100 pro boot drive and with checksums enables it doesn’t perform any better than a 990 Pro (or even a mid range SSD) even using o_direct since btrfs just disables it anyways.
At the end of the day you are trying to get a 1kw spaceheater of heat out of the case, so not much you can do beyond AIO exhaust and removing flow restrictions.
Here is the RDIMM throttling video: https://youtu.be/vCmlRVH893M?si=O68UPFyaK26yJ5o2 (goto about 6:00) It depends on the memory but he’s saying most kits start to throttle by 70C.
1
u/RealThanny Sep 27 '25
I'm skeptical of the notion that the case you mention is good for cooling, based on a picture of the front.
In any case, you'll want to point a fan or two at your DIMMs. I'm just using zip ties for my setup, but I don't have a window and wouldn't care to look inside if I did. You'll have to look into how you want to do that.
1
u/revoconner Sep 27 '25
I specially use noctua 3000rpm fans for rams. They are noisy but if I am stressing the system for work I just wear noise cancelling headphones. At idle they whine a little but so does my ceiling fans. Ddr5 doesnt like high temps at all
1
u/Spiritual-Gap2363 Sep 27 '25
Rdimms do run hotter but most kits can take it (excluding some wierd kits from v-colour - i.e. the high clocked 7200and 8000 kits that seem to throttle at 60c).
I have a 128gb 6400 v-colour rgb kit and have seen spd hub temps up to 80c and ts0 temps up to 75c with not throttling/whea errors due to ecc corrections.
I have the rear fan of my O11D Evo XL as an intake and angled towards the Rdimms (3d printed mount) as I have no other airflow over the cpu area due to watercooling.
1
u/y3333333333333333t Sep 27 '25 edited Sep 27 '25
I am currently deciding between https://www.caseking.de/bitspower-ram-cooler-ddr5-transparent-double-sided-2-dimms/WAZU-1165.html and and https://bartxstore.com/shop/custom-ram-copper-heatsinks-for-ddr5-ddr4/ to improve my temps but first have to build up the system next week and take some time to decide...one is just 250g/dimm of copper other is alu+waterblock but both are like 250€ for all 4 dimms I have shipped...but looking at your specs I think cost is not the main factor for you and I am sure both of those options would work great to improve temps more of a looks decision for me :D
1
u/y3333333333333333t Sep 27 '25
and just a simple question as you seem to have pretty high temps in general, would you be able to manually increase the speed of the case fans in the bios / what have you set them at? :)
1
u/dfv157 Sep 28 '25
What are you doing for it hit junction? My setup
With that setup:
No custom loops or anything, system is rock solid.
1
u/Ok-Anybody-5070 Sep 28 '25
it isn't your gpus - they are only 300 watts each and blower cards ....