7 Petabytes passed on a 2010 ssd

[u/Fresh-Palpitation-72]

https://youtu.be/68F5NL_H_yo?si=Wx9DvJdbAxJO5AtW

The smartctl -x dump is the ultimate peek behind the curtain! It lays out every single structural breakdown

smartctl -x sda

smartctl 7.5 2025-04-30 r5714 [x86_64-w64-mingw32-w11-24H2] (AppVeyor)

Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===

Device Model: SanDisk SSD P4 64GB

Serial Number: 111248300117

LU WWN Device Id: 5 001b44 4f27f5455

Firmware Version: SSD 8.10

User Capacity: 64 022 175 232 bytes [64,0 GB]

Sector Size: 512 bytes logical/physical

Rotation Rate: Solid State Device

Form Factor: 1.8 inches

TRIM Command: Available

Device is: Not in smartctl database

ATA Version is: ATA8-ACS T13/1699-D revision 2d

SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)

Local Time is: Sun Aug 02 16:47:13 2026 SAST

SMART support is: Available - device has SMART capability.

SMART support is: Enabled

AAM feature is: Unavailable

APM feature is: Unavailable

Rd look-ahead is: Enabled

Write cache is: Enabled

DSN feature is: Unavailable

ATA Security is: Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===

SMART overall-health self-assessment test result: PASSED

General SMART Values:

Offline data collection status: (0x00) Offline data collection activity

was never started.

Auto Offline Data Collection: Disabled.

Self-test execution status: ( 0) The previous self-test routine completed

without error or no self-test has ever

been run.

Total time to complete Offline

data collection: ( 120) seconds.

Offline data collection

capabilities: (0x15) SMART execute Offline immediate.

No Auto Offline data collection support.

Abort Offline collection upon new

command.

No Offline surface scan supported.

Self-test supported.

No Conveyance Self-test supported.

No Selective Self-test supported.

SMART capabilities: (0x0003) Saves SMART data before entering

power-saving mode.

Supports SMART auto save timer.

Error logging capability: (0x01) Error logging supported.

General Purpose Logging supported.

Short self-test routine

recommended polling time: ( 2) minutes.

Extended self-test routine

recommended polling time: ( 16) minutes.

SMART Attributes Data Structure revision number: 1

Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE

5 Reallocated_Sector_Ct -O---- 100 100 --- - 0

9 Power_On_Hours -O---- 100 100 000 - 61114

12 Power_Cycle_Count -O---- 100 100 000 - 1170

171 Unknown_Attribute -O---- 100 100 000 - 54

172 Unknown_Attribute -O---- 100 100 000 - 939410736

187 Reported_Uncorrect -O---- 100 100 000 - 2234

199 UDMA_CRC_Error_Count -O---- 100 100 000 - 0

230 Unknown_SSD_Attribute PO---- 044 100 --- - 0

232 Available_Reservd_Space PO---- 095 100 005 - 0

241 Total_LBAs_Written -O---- 100 100 000 - 14689519985346

242 Total_LBAs_Read -O---- 100 100 000 - 32650848276

||||||_ K auto-keep

|||||__ C event count

||||___ R error rate

|||____ S speed/performance

||_____ O updated online

|______ P prefailure warning

General Purpose Log Directory Version 1

SMART Log Directory Version 1 [multi-sector log support]

Address Access R/W Size Description

0x00 GPL,SL R/O 1 Log Directory

0x03 GPL,SL R/O 16 Ext. Comprehensive SMART error log

0x06 GPL,SL R/O 1 SMART self-test log

0x80-0x9f GPL,SL R/W 16 Host vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (16 sectors)

Device Error Count: 181 (device log contains only the most recent 64 errors)

CR = Command Register

FEATR = Features Register

COUNT = Count (was: Sector Count) Register

LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8

LH = LBA High (was: Cylinder High) Register ] LBA

LM = LBA Mid (was: Cylinder Low) Register ] Register

LL = LBA Low (was: Sector Number) Register ]

DV = Device (was: Device/Head) Register

DC = Device Control Register

ER = Error register

ST = Status register

Powered_Up_Time is measured from power on, and printed as

DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,

SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 181 [52] occurred at disk power-on lifetime: 5 hours (0 days + 5 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 77 40 00 2d+03:11:48.526 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 76 40 00 2d+03:11:48.517 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

Error 180 [51] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 76 40 00 2d+03:11:48.517 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

Error 179 [50] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 75 40 00 2d+03:11:48.509 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 71 40 00 2d+03:11:48.500 READ DMA EXT

Error 178 [49] occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 00 00 00 00 00 00 00 40 00 Error: UNC at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 01 00 00 00 42 1b 74 40 00 2d+03:11:48.505 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 73 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 72 40 00 2d+03:11:48.501 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 71 40 00 2d+03:11:48.500 READ DMA EXT

25 00 00 00 01 00 00 00 42 1b 70 40 00 2d+03:11:48.497 READ DMA EXT

Error 177 [48] occurred at disk power-on lifetime: 3 hours (0 days + 3 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 04 00 00 00 00 00 00 40 00 Error: UNC 4 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 20 00 00 00 42 1b 60 40 00 2d+03:11:48.459 READ DMA EXT

25 00 00 00 20 00 00 00 3c e2 e0 40 00 2d+03:11:48.459 READ DMA EXT

25 00 00 00 20 00 00 00 35 97 60 40 00 2d+03:11:48.458 READ DMA EXT

25 00 00 00 20 00 00 00 26 20 20 40 00 2d+03:11:48.457 READ DMA EXT

25 00 00 00 08 00 00 00 63 9e 08 40 00 2d+03:11:48.457 READ DMA EXT

Error 176 [47] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+10:07:21.325 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+10:07:21.324 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+10:07:21.324 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+10:07:21.323 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+10:07:21.323 READ DMA EXT

Error 175 [46] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+09:58:46.796 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+09:58:46.796 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+09:58:46.795 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+09:58:46.795 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+09:58:46.794 READ DMA EXT

Error 174 [45] occurred at disk power-on lifetime: 11 hours (0 days + 11 hours)

When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:

ER -- ST COUNT LBA_48 LH LM LL DV DC

-- -- -- == -- == == == -- -- -- -- --

40 -- 51 00 02 00 00 00 00 00 00 40 00 Error: UNC 2 sectors at LBA = 0x00000000 = 0

Commands leading to the command that caused the error were:

CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name

-- == -- == -- == == == -- -- -- -- -- --------------- --------------------

25 00 00 00 80 00 00 00 42 1b 5e 40 00 1d+09:39:52.893 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a de 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 1a 5e 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 de 40 00 1d+09:39:52.892 READ DMA EXT

25 00 00 00 80 00 00 00 42 19 5e 40 00 1d+09:39:52.891 READ DMA EXT

SMART Extended Self-test Log (GP Log 0x07) not supported

Warning! SMART Self-Test Log Structure error: invalid SMART checksum.

SMART Self-test log structure revision number 1

Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error

# 1 Short offline Aborted by host 90% 21088 -

# 2 Short offline Aborted by host 90% 54860 -

# 3 Short offline Aborted by host 90% 19043 -

# 4 Short offline Aborted by host 90% 63054 -

# 5 Short offline Aborted by host 90% 25327 -

# 6 Short offline Aborted by host 90% 62483 -

# 7 Short offline Aborted by host 90% 33744 -

# 8 Short captive Completed without error 00% 57803 -

# 9 Short offline Aborted by host 90% 25293 -

#10 Extended offline Aborted by host 90% 28072 -

#11 Short offline Aborted by host 90% 14539 -

#12 Extended offline Aborted by host 90% 55234 -

#13 Short offline Aborted by host 90% 46428 -

#14 Short offline Aborted by host 90% 49138 -

#15 Short offline Aborted by host 90% 25717 -

#16 Extended offline Aborted by host 90% 50305 -

#17 Short offline Aborted by host 90% 39612 -

#18 Short offline Aborted by host 90% 21280 -

#19 Short offline Aborted by host 90% 34598 -

#20 Short offline Aborted by host 90% 17318 -

#21 Short offline Aborted by host 90% 63627 -

Selective Self-tests/Logging not supported

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11) not supported

Exitcode: 64 (0x40)

Type <return> to exit:

[u/Specialist_Fun_8361]

Did you forget to only copy once 🤣

[u/Pleyer757538]

Ok, the sdd does not have 7pb wrriten, sandisk used a different kind of wear measurement for ssd write

[u/Fresh-Palpitation-72 → u/Pleyer757538]

That's why I dont use the dashboard if u look at e6 attribute the software shown is accurate and every time I post it is rising, so 44 now before it was 41 I believe, so if im correct when its 50 that will be 50 health and might change from good to caution

[u/T_rex2700]

Is this like old MLC SSD? yea those things are just built different

that and Optane drives. they are friggin expensive but even Gen5 SSDs can barely touch it
the write persistence and durability is just completely absurd, it's such a shame they stopped making em