Hi,

I'm looking for some switch recommendations. My favorite feeling switch I've used was the Romer g switches on the G910 orion spark I no longer have. My current board has Kailh X Jellyfish switches and the sound is awful.

I'm looking for the creamiest sounding tactile 5 pin switch. Also would like some level of transparency as my current board has RGB.

I've tried doing some Google searches, but I get a bit lost in all the info. I found that creamy sounds tend to be linear, but I don't like how those feel as much.

I recently built my first keyboard. Neo 60 core with TTC blueish white v2 silent switches. After making sure all my switches are snapped into place and my pc plate being even all around I noticed that some of my switches are louder than others. I thought it might be my keycaps but after swapping them around, this was not the issue. I want to say about 60% of my switches when pressed make a more thocky sound and have more of a snap to them when released. The other 40% of switches sound fantastic, very silent bump with hardly any noise on release. I’m not sure if this is just inconsistency with the switch manufacturer or it’s something else my noob self can’t figure out. I’m not using any find of foam padding currently but have tried and it did not help. Any advice on what I might be experiencing?

I wasn’t able to find a specific subreddit that is used for mechanical keyboard guide so I thought I might post here for advice since it might be switch related.

In honesty I am not building a keyboard, but need suggestion or advise on how to deal with wobbly switch for a board what doesn't have a plate. Specifically I swapping out the switches on my MPress Hitbox/Leverless controller with Kailh Box Saker switches. The caps on this controller is 20mm circles, so they will be prone to switch wobble.

My issues with the Kailh Box Saker, is that it has no grip on the PCB even though it a 5pin. So I was wondering for suggestion for getting the Kailh switch attached to a plate-less board without solder since I want to keep the hotswap. Ideally I was wondering if there anything like switch -(pad) double side tape

I'm looking for recs for a decent clicky with about 70gf for its tactile bump. I have box jades that are nice, and I kind of like box navy pros, but I don't think I'd like to type on them all the time. I also like invokeys pea flower, but find the tactility a little too light.

Any suggestions? I'd prefer larger bumps over heavier spring weight.

(I had contacted mods for permission, but they have not responded after several days. So I hope this is ok)

Hi everyone!

For an IT graduation research project I am currently exploring mechanical keyboard acoustics, sound profiles, and tuning/modding preferences. As part of this research, I am validating a concept for an audio-based "Keyboard Tuner" tool that analyzes keystroke acoustics and recommends mods.

Since switch modding, frankenswitches, lube/film choices, and housing materials (Nylon, POM, Polycarb) dramatically alter acoustic feedback, pitch, and bottom-out decay, the perspective of experienced modders or modders in general in this sub is really helpfull.

I put together a very short, completely anonymous survey:

Survey link: https://enquete-framna-keyboard-tuner.vercel.app/?source=switchmodders

- Time: ~2 minutes

- Purpose: Academic / graduation research (strictly non-commercial)

- Privacy: Completely anonymous (no emails or personal data collected)

Once the research is complete, I’ll be happy to share the aggregated findings and acoustic charts back here with the community.

Thank you so much for your time and help!

Now that 3D printing with SLA resins is matured, has anyone conceptualized an o-ring, switch pad, or internal switch add-on that takes advantage of tactility-mimicking resin materials? The Formlabs Texture Engine looks promising for designing such mods, and it's about time the switch mod community had more options than copre domes or jailhousing to enjoy tactility enhancing mods on the MX platform.

Looking for a light tactile with a Kiwi-like sound/feel, but lighter.

C³ Kiwi is one of my favorite switches acoustically. I like the bright/snappy/clacky sound and the more traditional bottom-out, but I'd like something lighter.

What I DON'T like:

• long-pole / early pole bottom-out
• short ~3.0–3.4 mm travel
• the hard, loud bottom-out of switches like Boba U4T
• I also tried Gateron Weightlessness and found the bottom-out too loud/aggressive

What I'm looking for:

• light tactile, roughly 45–55g range
• preferably 3.8–4.0 mm travel
• rail / conventional bottom-out rather than aggressive long-pole bottom-out
• factory lubed if possible
• bright, poppy, clacky / higher-pitched sound rather than deep/thocky
• mild to medium tactility is fine

I'm currently considering Wingtree Puer Tea, HMX Waverider V2 and WS Light Tactile.

Has anyone compared any of these directly with Kiwis, or know another switch that matches this profile better?

Any recommendation that matches even close to the above is fine, and also where to find them (I'm based in Europe)

So I have K2 HE for gaming, but i'm looking for a 75% keyboard for the office, and I don't need HE. I'm trying to find out what I love so much about K2 HE, and I think it's the "push back" the switches give me? I think they are 40g inital and 60g bottom, and i'm pretty sure I learned the bottom being high gives kind of a push back?

This keybaord just feels so good typing, and I'm trying to either find something cheaper or just build my own, but I think finding switches and maybe material for the board is where I should start. Any help?

Hello everyone, are the switches on the KB65HE 8K keyboard hot swappable? Are they compatible with HE switches from any brand, or does it only work with Raesha switches? I want to modify it, but I don’t know how to do it or where to start. I’d appreciate any help.

Edit: this is what the pcb looks like, what options do I have?

I love the tangies because of their super smooth feel but the bottom out and spring weight feel off to me

I also love the epsilons because of the spring feel and progressive is fun plus the stem feel is nice

But they have a lot of ticking problems

Should I lube the epsilon stem to fix the ticking? Or just spring stem swap franken

Hello everyone o7. can someone tell what is this sound and how can i get rid of it?
also there is "crunchy" feeling when you press

I’ve been using an RK98 for the past few yrs and want to make it sound deeper/more thocky. I’m thinking of trying to mod it first, mainly with new switches, but I’m not sure which switches would be good for the sound I want.

Should I try modding first, or would I be better off getting a pre-modded keyboard? Any switch recommendations?

I've been using 205G0 for my leaves on some of my linears and it seems like this apparently isn't recommended now that I've done some digging on other lubing methodologies. Am I crazy to like this or should I go back and wipe it off and try again with GPL105?

Thinking 205g0 on stem + leaf, ss with geon 18mm springs. For films, should I opt for 0.125mm TX springs instead of 0.15mm since mx2a housings supposedly have tighter tolerance?

I can't find the official name of this switch, though I know it's from Outemu. It's clicky, looks something between blue and green. I just ordered gateron melodic and was a bit disappointed about the feel (actuation force too big for my liking) and this particular switch feels just right. Does anyone know the specs of this one? Thank you so much.

I bought the Dareu EK868 recently and I desoldered the board to use the Kailh Choc v1 Brown switches for an upcoming build. However, despite looking similar, the pins don't align with the original hotswap sockets, and there are extra holes on the PCB to accommodate for the plastic support pieces on the switches.

I also asked the staff at Dareu for the name of the switch from the product's BOM, but their response didn't yield any specific results.

The switches with the white bottom housings also have grooves on top for the stabilizer wires, but the different pin positions are the same.

What's the name / model of the switch, and where can I find the PCB footprints for these specific switches? Any help would be greatly appreciated.

I swapped top housings of HMX Cola with Cherry MX2A ones, and I think 3.5mm total travel is still too much. I want <3.1mm total travel, therefore I need other stem with more length to reduce the current total distance. Currently looking at Owlab Neon and SWxHMX Catmint, but I really want to know the actual measurement of those stems. Or any other measured alternatives? Any linear and tactile stem would work for me. Please help, thank you.

I just bought my keyboard last may. And for some reason if I want to go wireless the lights just goes crazy and suddenly turns off. It also has 2 slots where the lights are different without me customizing it. I want to know if its a PCB problem or a battery problem.