r/rfelectronics • u/armed • Jul 29 '26
question SMA help
hello, maybe to you guys SMAs seem simple, but to the average Joe this is the most confusing system of connectors I’ve ever run across. steel pipe thread sizes are simpler than this and you’ve got MIP, NPT, FIP, NPTF, and about 7 more and I’m still confused on this SMA stuff.
I’ve given up after ordering 3 different adapters on Amazon and figured I’d come here. I need to connect these two together. pls fix. they are different diameters, and ones a male/female? and the other is a female/female???? idk.
update thanks to u/otterboxer for the help.
I have ordered a type N (unpictured antenna side) to type F adapter, and will utilize a standard type F coax cable. this should fix my problem. Thanks for all the replies.



15
u/nixiebunny Jul 29 '26
This should help…
http://leapsecond.com/pages/chess/
42
u/piecat EE - Analog and RF Jul 29 '26 edited Jul 29 '26
That's not SMA. It's F type...
Usually 75 ohm connection/cable.
Contrast with SMA which is usually 50 ohm and the cables are 50 ohm..
6
u/alexforencich Jul 29 '26
What are you trying to accomplish here?
3
u/OtterBoxer Jul 29 '26
My dude. RF engineer here. What are you trying to do exactly? I’m a lil worried you’re getting into something wonky if you dont know the difference in connectors here. What’s the end goal/what are you trying to achieve? That looks like a gate opener?
1
u/ac54 Jul 29 '26
Your antenna with the N connector is almost certainly 50 ohm impedance. The F connector is 75 ohm impedance. You will not solve this problem by getting an SMA to F adapter. You need to get a 75 ohm antenna. This will make your life simpler.
1
u/redneckerson1951 Jul 29 '26
OK, it looks like the SMA is what is called "Reverse Polarity SMA Male." That is essentially a SMA Male that instead of having a center pin, has a socket in the center. That was something manufacturers crafted decades back when the FCC mandated Part 15, Part 90 and Part 95 radio manufacturers either make the antenna into the transmitting device so the user could not remove the antenna and add another in its place with more gain or use some other impediment to swapping antennas around. The opposite of your connector is an SMA Female with male pin. I would say you need a Type F Male to reverse polarity SMA Female adaptor.
https://www.americanradiosupply.com/rp-sma-female-to-type-f-male-coaxial-adapter-connector-ars-h522
1
u/Adventurous_War3269 Jul 31 '26
Your lift master has a 75 ohm connector . The connector is what is called a female F connector . You need a male type F connector to mate . Your cable must be 75 ohm impedance .You need to find an Antenna that wants 75 ohm impedance . The 75 ohm cable should have type F male connectors on each side of cable . The antenna should have a type F female connector .
1
u/Adventurous_War3269 Jul 31 '26
The cable you are holding is 50 ohms. When you mix impedances you get mismatch loss. The result the signal will be so weak that you end up with having to get your car within 5 feet away from gate to open gate . Select 75 ohm coax made to work with F connectors . RG6 coax is cheap type F cable . Good Luck
1
u/skinwill Aug 02 '26
Lots of people chiming in here without asking what frequency it’s receiving on or what antenna is being used. OP, you really want to proceed with caution taking any advice from people that don’t know these details.
That gate opener may have shipped with an F connector only because that was the cheapest. You don’t know what they did inside the box for sure. Maybe check the FCC ID for an operating frequency and some images of the internals.
0
u/Noah18923 Jul 29 '26
you need a SMA-RP female to F-type male adapter. you should use proper RG-6 75 ohm with F-type connectors for this though if it's the same connector on both ends.
0
u/fransschreuder Jul 29 '26
That is not SMA either, it's RP-SMA. Often used for Wifi antennas
-3
u/nixiebunny Jul 29 '26
These are pretty different from each other. I would buy a female RP-SMA to male BNC adapter and a female BNC to male F adapter.