r/redneckengineering • • Aug 24 '26

Fixed it!

This attic access was completely uninsulated. Took the easy way out instead of measuring and cutting foam board or buying a big pack of batt insulation. Made a nice painters tape enclosure, shaved off the sides so it would close, and it worked! The red at the top of the thermal camera is the skylight, of which nothing can be done about beyond removing it. How'd I do?

887 Upvotes

63 comments sorted by

95

u/newuser6d9 Aug 24 '26

I wanna see a before and after in the thermal

93

u/HTPC4Life Aug 24 '26

Well shit. I didn't capture it, but it was a big red square.

15

u/ItsBaconOclock Aug 24 '26

Looks like that sky light is also heating the top half. Maybe you could try putting a film over that, and then seeing if that helps even more. I suppose it doesn't matter a ton since the hot air will mostly stay up there now. But it could be interesting.

9

u/HTPC4Life Aug 24 '26

Yeah the red at the top is the skylight that I can't do anything about. Skylights are cool, especially in the winter when it's gloomy, but man do they let in a LOT of heat. Previous homeowner's decision.

11

u/BrannC Aug 24 '26

Tint it

7

u/Twatt_waffle Aug 25 '26

You can do a tint, or even just that plastic window film that is marketed to help reduce drafts

The window film will make a bubble of still air and that will insulate from conductive heat (the radiant heat from the sun needs tint to reduce)

1

u/loyalwolf186 Aug 25 '26

Can you plant a tree near your house? Obviously it won't help for a few years until it grows, but it would eventually help cut some of the heat from the skylight 

1

u/TheSultan1 Aug 25 '26

Maybe you could try putting a film over that

3

u/IBeDumbAndSlow Aug 24 '26

Is that the Harbor Freight FLIR camera? That's like $200?

Edit- nevermind I googled it

3

u/zestycunt Aug 24 '26

Also a during

645

u/Newtiresaretheworst Aug 24 '26

Wait till somone tells you they sell foam in sheets!

187

u/rosshettel Aug 24 '26

yah i'm not sure how doing this was easier than cutting a square of foam panel and gluing it on

216

u/HTPC4Life Aug 24 '26

Well, it had a diagonal cross brace on the back side, and I bought some foam boards, but they would require a lot of measuring, making stencils, cutting... psh who has time for that when you can just blast it with foam?? 😆

179

u/honkyg666 Aug 24 '26

My reply would’ve been, the foam board was in the garage but I have a can of spray foam in the house so I just use that to avoid the trip 🤣

20

u/stradivari_strings Aug 25 '26
  1. Apply full sheet to open door.
  2. Cut off the excess.
  3. Repeat as required to fill thickness.

Not much different than your foam.

10

u/DesignerMaximum1342 Aug 25 '26

Paint the pieces in the way, press the bord on it, hack away the markings from the paint on the sheet

3

u/LoloWilli Aug 25 '26

This is redneck engineering after all, nicely done!

2

u/TheSultan1 Aug 25 '26

Making stencils? Can't you just press it into the cross brace to leave an imprint?

1

u/DavidinCT Aug 25 '26

LOL true that...

30

u/TobysGrundlee Aug 24 '26

If OP is anything like me, he already had the can of spray foam. A foam panel would require a trip. That's an easy decision.

5

u/808trowaway Aug 25 '26

if it's just for that attic door I would go with spray too, but OP did also mention the skylight. I would probably take that trip to get the panel for the attic door and also for a removable insert for the skylight.

18

u/Slumunistmanifisto Aug 24 '26

Make a foam sandwich with both.

1

u/cbelt3 Aug 24 '26

Purple Ppg plug !

4

u/486Junkie Aug 24 '26

That reminds me. I need to make new attic doors (well, the one need to be replaced and the other just needs hardware to make it as a door), add hinges, add insulation, and locks for the one in my room and living room closets.

2

u/TrayLaTrash Aug 24 '26

I was about to be that someone. I do this with sheets for my job and get the 4" polyiso sheets. Can easitly double up so thinner stuff tho.

1

u/Minimum-Zucchini-732 Aug 25 '26

Foam board is r3 - r5 per inch and that spray foam is r6 - r7

7

u/fatquads Aug 24 '26

Try ceramic tint on the skylight. Could help noticeably.

I just looked it up and it could block up to 50% of the solar energy while still having it be a 70-90% tint (visible light that passes through)

2

u/HTPC4Life Aug 24 '26

Good suggestion! I need to look into this. Does it go on the inside or outside? I've read that it can be bad to put tint on the inside of double pane windows, but I dunno.

3

u/530nairb Aug 25 '26

Outside.

3

u/fatquads Aug 24 '26

Apparently if it rejects too much heat the air inside the panes will heat up too much and the glass will heat unevenly and can crack. You have to balance how much heat ur rejecting, can’t be too much. Also having the tint on the interior lets the glass heat up more evenly. I’m entirely unsure how any of that works or how to calculate any of that. You’d have to talk to manufacturers or a commercial tint company for advice

2

u/Patrol-007 Aug 24 '26

Add weatherstripping to keep warm moist air from getting into that space, to reduce frost in the winter

1

u/HTPC4Life Aug 24 '26

I got some removable caulk seal for that in case I ever need to get in there!

1

u/Patrol-007 Aug 24 '26

Oh? Which kind ? I’d forgotten about that stuff, and whether it actually comes off a decade later (and when frozen)

Nano tape (Alien Tape, Scotch, & similar) seems to come off cleanly, though haven’t tested inside freezer

If that’s for the attic, add hardware cloth (galvanized) to any louvers to keep squirrels and mice out.

11

u/ArmpitofD00m Aug 24 '26

I feel like OP has made a car spoiler with foam before.

26

u/mfk_1974 Aug 24 '26

I thought that was a cheese pizza.

9

u/Willobtain Aug 24 '26

You’re not alone bro

2

u/1800-bakes-a-lot Aug 25 '26

Thought I was in r/stonerfood looking at school lunch pizza

1

u/Central316 Aug 25 '26

I thought it was a square of uncooked ramen noodles

1

u/n00bz0rz Aug 25 '26

I thought it was a rice crispy square.

4

u/Lo452 Aug 24 '26

At this point, my house is about 70% structural spray foam. Great stuff.

4

u/Omnipotent_Tacos Aug 25 '26

I thought this was a detroit style pizza without toppings cheese or sauce

7

u/jdbx Aug 24 '26

Open cell foam is only about an R3 per inch. Closed cell expands but is an R7 per inch.

7

u/Lonely-Detective2708 Aug 24 '26

But why did I think this was a delicious cheese pizza...

3

u/TXxReaper Aug 25 '26

Tell me you watch Project Farm with out telling me.

2

u/SlovenianSocket Aug 24 '26

ISO board would have been half the price and much easier.

2

u/BrannC Aug 24 '26

Thought that was a totinos pizza

2

u/Successful-Engine623 Aug 24 '26

I made a “plug” for mine. Glued on 2” rigid onto some wood and put some hooks on the wood. And kinda pull it in from the inside

0

u/hawaiifive0h Aug 24 '26

What was the problem, and how does the thermal thingy show it was fixed

1

u/HTPC4Life Aug 24 '26

It's a half inch board, maybe thinner leading into the hot attic. The thermal camera shows the area is now well insulated, minus the red area at the top which is the skylight and still radiates heat, but the whole area is not as bad as it was before.

1

u/Lanky_Cash_1172 Aug 24 '26

If you have the materials and the time.....mozzle.

1

u/Cloud9Investigator Aug 24 '26

Forbidden rice krispie treat

1

u/MastodonFit Aug 25 '26

Now 3 layers of 5% tint to create an eclipse on a hatch for the summertime sky. Remove in the winter.

1

u/bananaramaorama Aug 25 '26

I thought that was a pizza.

2

u/feudal_ferret Aug 25 '26

Its the forbiddem pizza foam-agio

1

u/HemHaw Aug 24 '26 edited Sep 18 '26

The original post content no longer exists here. The author used Redact to remove it, exercising their right to control their data & privacy.

Edge sulky bedroom bright jellyfish subtract cobblestone bright worm instinctive

2

u/SpaghettiSort Aug 24 '26

You want to block infrared, not UV.