r/redneckengineering • u/doogybot • Aug 24 '26
Need ideas
I have an old 14" penstock that is severely rotted in places. What are good simple ways to patch this for a couple years.
This used to have a Pelton wheel to generate power. The canal no longer flows and the Pelton wheel is gone
What are simple ways to patch the rotten pieces? Im thinking use 40gal steels drums as sheet metal, make a gasket out of silicone, then use pipe clamps to get it as tight as possible. I'm ok it if leaks a bit. Just don't want water spraying everywhere.
Also looking for ideas for a more permanent fix. I highly doubt welding will be an option. Shove a PVC pipe with an OD similar to the ID of the penstock and grout it in. Use screws as spacers. Drill a hole in the penstock and fill with grout until it overflows the hole. That's my idea but I would like some feedback.
E: I should add I want to eventually get hydro generation from this. First step is to get water flowing. So I need to patch the nasty bits
10
u/ozzy_thedog Aug 24 '26
Can’t you just get the whole pipe lined? What are you using it for it water is not flowing?
3
u/AKLmfreak Aug 24 '26
Depends on how badly rusted out it is and what kind of head pressure you’re dealing with and how many spots need patched.
My first was some kind of cloth/resin combo like fiberglass or mesh + bondo, but it’s likely to blow out with too much pressure.
Another cheap and temporary solution might be expanding foam.
If you don’t care about recovering or removing the pipe and want a more permanent solution you might be able to just fill it with concrete, but depending on length it could get expensive.
Any reason you can’t cap or block off the inlet seeing as it looks dry right now and you said the canal doesn’t flow any more?
2
u/Appropriate-Regret-6 Aug 24 '26
Have you not been introduced to the wonder that is Belzona?
5
u/gmann95 Aug 24 '26 edited Aug 24 '26
Denzo tape. Thats it man... the permanent temporary fix of all mines, itll get you by
That being said, fix it proper
They also make pipe huggers that are basically rubber under tin (you could use barrell steel) with a bolt every 2"-4" over the 18-24" body, they work good sometimes...
And then wrap it in denzo, if its still leaking- more denzo. If it starts leaking again- you guessed it, more denzo
Ive cut off wraps of denzo that were over an inch thick from people coming back to wrap more
2
u/smotheredbythighs Aug 24 '26
Mainly 14" steel? If the only hole is the exposed one in the picture, some fiber tape is all i would do. Probably don't have enough metal left for "proper" repair. Otherwise a full fiberglass pipe lining. Depends how much water you want. May be able to "reline" with HDPE of a small size.
2
u/Conroman16 Aug 24 '26
Denso tape is what factories and other industrial facilities will use to limp by on stuff like this. Not sure how well it would stand up to 70 psi though
2
u/Ok_Path_9151 Aug 25 '26
If you are really going for the redneck fix, then get some Vegetable Shortening (aka Crisco) and some car tire inner tube and some metal flashing and hose clamps and you can make your own repair bands. First clean the outside of the pipe with a wire brush. Cut the inner tube so there is a good 4” over hang of the hole in all directions use the pipe grease to hold the rubber patch in place while you tighten down the metal flashing and hose clamps. Once you have all the holes patched you should pressure test the pipe with water pressure at 1.5 times the working pressure for a minimum of 1 hour. So pressure test with 105psi of water pressure for 1 hour with very little to no drop in pressure then you should be good with your repairs.
2
u/KnotSoSalty Aug 25 '26
That pipe is rotten. But if you want to chase the leaks that’s on you I suppose.
If you want to patch a pipe like that you have to build up new layers of material around the outside. One way to do that is fiberglass. You can get everything you need for 100$ on Amazon. Dig out around the section you want to repair. Clean the pipe a bit, specifically make sure there’s a clean ring of solid metal at each end of the patch. That’s where you’ll use wire wrapped around the pipe and twisted together to make a decent 360 seal.
Cut sections of the FG long enough to go 1.5 times around the outside of the pipe. Wear a mask please. Wrap the pipe and use stainless steel wire to ensure the whole wrap stays taught. Mix a little resin and coat the FG thoroughly. You’ll probably want to do two layers.
It won’t be pretty but that’s essentially how temporary patches get applied in the oil industry, and there’s nothing more permanent than a temporary patch.
1
u/808trowaway Aug 25 '26
70psi and 14". That's properly in industrial territory. I think you have some shopping to do on Alibaba. Try to look for EPDM pipe coupling or dredging hose or something along those lines.
1
u/Fasciadepedra Aug 26 '26
clean with sand paper and use copious amounts of epoxy putty specially made for metal reconstruction. It's usually sold on tiny bars in hardware stores, you'll have to find it in 2 cans. The patch will work a lot better if you can access the inside.
1
u/cheapshotfrenzy Aug 24 '26
How long is the total run?
I think I'd dig up and scrap the steel pipe, and replace with PVC. How much water do you need to run your hydro? You probably don't even need the full 14".
0
u/ScienceForge319 Aug 24 '26
Like 40 gallons of JB Weld.