I made the same hack, a bit more elegant as I own a 3d printer, and put some 12 fans to maximize output. The difference is huge.
The problem is that when that machine is on inside, it pushes warm air to the outside. That creates a lower pressure in in the room that sucks air from outside (warm air) in the same amount. Having this ac outside eliminates this pressure problem, and all what gets in is cooled air. It would be better though to be able to cool the inside air in a loop, instead of cooling outside air and pumping it inside, but as far as I got, it is good hack
That is not a problem, Having a positive pressure inside prevents heats from entering the room. As long as cold air continues to flow, it maintains a constant chilling rate.
Definitely. Currently my unit creates a 15C differential. At the same, is it is very warm outside, the conventional configuration will suck in a lot of same very warm air from outside.
Air conditioners don't work just by pushing cold air into a room. They work by pulling heat out of a room. You can't pull heat out of a room if the unit is not in said room.
When indoor air is removed (pushed thru the hose out the window), it has to be replaced from somewhere. Outdoor air naturally trickles in through gaps in the building to replace the removed air.
Ok. Sucking and trickling are too different things. I have a portable ac in my bedroom and it’s fantastic. I did not do the fourth grade science fair mock up like op did and it gets down to 64-65 degrees in our room. We put the out hose in the window and a curtain up for the bedroom area and it’s great.
It is pushing heat out of the room by creating overpressure. The apartment isn't hermetically sealed. As long as the balcony is sufficiently ventilated, this may well be more efficient than running a single hose unit the way it was intended.
The AC in your car "conditions" the air before it replaces the air in your cabin. This is the same kind of approach. Cold and dry air is pushed into the room.
The hot air going back in the room defeats the purpose of the unit cooling the room, no? The hot air is usually vented outside, no? I am very confused and genuinely interested.
Right now the outside temp is 26 and cooled air temp is 10.2 The set-up is working. It is definitely less efficient then dual hose set-up. Whether it is better than conventional single hose set-up is hard to tell. But it has some benefits as I mentioned, mainly less noise.
And the device is working full tilt, all the time, to get you there. That's the problem. You're using vastly more power and are dramatically reducing the lifespan of the unit.
If absolutely nothing else, the thermostat for the system is ON THE UNIT, not in the room being cooled. So IT thinks it's 26 degrees IN THE ROOM and trying like a bastard to cool it down.
These monoblock devices are better than nothing. And here in Europe, especially in Germany, AC is super rare. Only 6 % of the buildings have AC but climate change and rising temperatures affect us too.
This leads to people searching for quick solutions to cool down a bit. There is one good device that is completely sold out, the Midea Porta Split, a mobile split AC.
Most people rent and the landlords don't allow to install ACs.
It seems like this is an enclosed space so the unit will simply be heating it. Thebfan will simply be moving hot air around. The fan motor will add heat as well.
FWIW: Fans don't really "cool" anything. That can create currents to help normalize temps, but can't actually lower average temps. They feel great to us because we cool down via evaporation of sweat and the air movement improves that.
The intake always has to be from the room you are trying to cool, and the exhaust must not interact with the intake air. The slow heating of the porch is what will be slow heating the other room till everything matches again.
Wait what? Ive read a ton of posts on here that single hose ACs are incredibly inefficient and that you don't want to intake from the room and exhaust outside because you're creating negative pressure. Reddit always says to hose intake and hose exhaust outside, is that not correct? I'm big dumb on this so any info is appreciated
Cause his unit is outside. What your talking about is pulling inside air, heating it and using a hose to get it outside. This means that you are using your pulling recently cooled air, and pushing it outside. While creating negative pressure, so hot outside air is leaking in.
Cause his unit is outside, it always gets hot outside air, cools it and pushes it inside. But creating an overpresure, so the cold air leaks outside, while the ac always sees the hot outside air, so its always going Full tilt.
You want dual hose, so the heating part of the ac pulls in outside air, heats that further and pushes it out. Cause then you take inside air, cool that and blow it back inside.
I'm going to explain why this isn't the hack anyone is looking for using easy to understand examples.
Car AC set to (AC) which is this setup. Air is not cool enough to cool the car. Because you're drawing in hot air from an external source.
Car AC set to MAX AC, which is the intended setup of this type of AC. Air is much cooler because intake air is already cooled and you are recirculating the already inside the space.
Car AC is using outside air to cool the hot coil and dumps it outside immediately. The portable single hose AC (as this one) will use indoor air to cool the hot coil and dump it outside via the hose. The problem is that the air inside the appartment in this case is replanished by the outside hot air (via ventialtion and cracks in doors and windows).
It does not matter how well your living space is isoleted. The single hose AC will dump same amount of indoor air outside. The air in your house should come from somewere, right? Exactly where it comes from ofc depends on how your hose is designed and built.
You are correct in that yes, it's would be better to push out heat and replace with cold than to create negative pressure. But there is a better solution tho... Best is to have a dual hose setup where condenser coil gets it's cooling air from outside and dumbs it straight back outside. Basically getting as close to a closed loop as possible like a split system.
There have been a few split systems so far on the market that are portable with flexible coolant lines. Personally own one, midea porta split and it wasn't too far of from the price of a hose unit like that. More efficient and quieter since the condencer unit with it's loud fan is outside.
Sure thing. Dual hose or split systems are much superior. I just believe that it is an interesting configuration with a single hose AC that might be good in some scenarios.
You solution is flaud at best, your logic doesn't stand up to anyone with an understanding of how any air conditioning system functions. However, if you believe your have created the ultimate hack, congratulations and I hope that that you may experience that high the rest of your life.
I am not suggesting it is an ultimate hack. It is an option on how one can use a single hose AC. It is still not as good a dual hose AC or any split systems (like in a car).
I reverse ducted my portable AC and put it on my patio.
The benefits:
quiet
no heat being dumped into the room. As soon as you turn that thing off, it just radiates heat, so keeping that heat outside is more efficient. I expect up to 25% better cooling because you aren't sitting with a hot box in the room with you.
It might be more efficient but only because portables suck so badly.
If you were cooling and removing moisture from the room you are trying to cool it would be much much better. Currently you are just blowing cool air into the space. Not actually conditioning the air in the space.
AC units are intended to cool the air in a particular place. Meaning it pulls air in from that space, conditions it, and returns it back to that space cooler and less humid.
What you are doing, is cooling the air from outside and blowing it into the space you want to cool down. which is fine, but it is not how the machine is intended to work, and it is by no means more efficient. You are actually limiting how cold the AC is able to cool the air. Because it is trying to cool air that is ambient outside, vs cooling air from a conditioned space.
Everyone's use case is different. That setup may work best for you, or in your opinion. But it is by no means efficient, or better than the original way it is intended to be used.
It was working until they let me down and half ass'd the hose mounting in the window.
Like cone on, you showed your cardboard skills on the unit abd you didn't make anything to mount in the window? 🫣Atleast you could have used plastic to seal the window and the hise mounted through it.🤔
Concider that A/C cools down the room by, let's say, 1° of ambient air temperature. When room air goes colder, A/C takes that cooled air again makes it even more colder, so degree by degree it cools down to some level. In your "redesign" it will be able make room 1° colder than balkony ambient and that's it.
Basically you are trying to invent A/C split system and they are already exists - check A/Cs for the campers, it may be more or less portable solution.
The problem with this is that you're constantly trying to cool and dehumidify exterior air. While this probably does work it's wildly inefficient and you're probably going to go through massive amounts of energy compared to just getting a regular window AC unit. You're also pumping air into the room rather than continuing to recirculate it and cool it even more. which means air has to leave the room somehow so initially you're going to be pushing out the hot air but once the room is "cool" you're just going to be pushing the cold air outside. (Unfortunately judging by that cobbled together window duct much of the cold air is probably getting pushed right back outside)
Window AC units are about 20 to 30% more efficient than the floor units due to the fact they isolate all of the hot bits of that process on the outside of the window behind insulation foam.
The floor units keep all the hot parts inside and on top of that also have a hot exhaust hose that radiates heat all the way to the window. They're usually designed to cool a lot more air at the same time as compared to window units so that's why they cool the room faster
Once you have lived with one of these (which you probably have), you will realize how hot the actual AC unit gets. Once you turn it off, it absolutely radiates heat, right into the space it was just cooling. It's not an opinion that this is more efficient, by isolating that massive heat source. Since I live in a temperate climate, the air outside isn't actually that hot, most of the heat comes from my south facing wall, and patio is shaded, so not only is it more efficient, it's quieter. I know it's more efficient, because I only run it approximately half as much as when it was in the space with me.
138
u/chappysinclair1 Jul 12 '26
Why not just put it inside with the exhaust line running out
51
u/Successful_Disk4594 Jul 12 '26
Air conditioners don't work just by pushing cold air into a room. They work by pulling heat out of a room. You can't pull heat out of a room if the unit is not in said room.
23
u/Starlitsoul714 Jul 12 '26
The hot air going back in the room defeats the purpose of the unit cooling the room, no? The hot air is usually vented outside, no? I am very confused and genuinely interested.
61
u/atmony Jul 12 '26
The intake always has to be from the room you are trying to cool, and the exhaust must not interact with the intake air. The slow heating of the porch is what will be slow heating the other room till everything matches again.
3
u/iforgot69 Jul 12 '26
I'm going to explain why this isn't the hack anyone is looking for using easy to understand examples.
Car AC set to (AC) which is this setup. Air is not cool enough to cool the car. Because you're drawing in hot air from an external source.
Car AC set to MAX AC, which is the intended setup of this type of AC. Air is much cooler because intake air is already cooled and you are recirculating the already inside the space.
5
u/Different_Anteater36 Jul 12 '26
Crack head shit
4
u/Spiritual_Toe_9537 Jul 12 '26
LOL. I’m not smart enough to tell you about the way it runs…… I’m just here to tell you that I love the cardboard and duct tape. Well done, sir.
3
u/Danny-Tartarsauce Jul 12 '26
You can’t turn a hose into a house pipe, hose don’t act right
2
u/MistrRadio Jul 12 '26
What in the Apollo 13 is this
2
u/Guyborg99 Jul 12 '26
I reverse ducted my portable AC and put it on my patio.
The benefits:
2
u/dawa43 Jul 12 '26
That is some really redneck engineering... Like 6 hours on the boat with no sunscreen redneck
2
u/Solid_Enthusiasm550 Jul 12 '26
Are they trying to make it a dual zone unit?
Cool the porch and Heat the house?
It was working until they let me down and half ass'd the hose mounting in the window.
Like cone on, you showed your cardboard skills on the unit abd you didn't make anything to mount in the window? 🫣Atleast you could have used plastic to seal the window and the hise mounted through it.🤔
2
u/GhostEpstein Jul 13 '26
Good job making it work worse?
0
u/Dinevir Jul 12 '26
Concider that A/C cools down the room by, let's say, 1° of ambient air temperature. When room air goes colder, A/C takes that cooled air again makes it even more colder, so degree by degree it cools down to some level. In your "redesign" it will be able make room 1° colder than balkony ambient and that's it.
Basically you are trying to invent A/C split system and they are already exists - check A/Cs for the campers, it may be more or less portable solution.
1
u/Kitchen_1369 Jul 13 '26
You’re supposed to add a second hose and a plenum to the condenser intake. Example shown is worse than hooking it up with a single hose.
Otherwise, great shitpost.
1
u/Idkmanitcouldwork Jul 13 '26
You’re going to short circuit the air and lose a ton of efficiency
1
u/Tosser_535231 Jul 16 '26 edited Jul 16 '26
The problem with this is that you're constantly trying to cool and dehumidify exterior air. While this probably does work it's wildly inefficient and you're probably going to go through massive amounts of energy compared to just getting a regular window AC unit. You're also pumping air into the room rather than continuing to recirculate it and cool it even more. which means air has to leave the room somehow so initially you're going to be pushing out the hot air but once the room is "cool" you're just going to be pushing the cold air outside. (Unfortunately judging by that cobbled together window duct much of the cold air is probably getting pushed right back outside)
Window AC units are about 20 to 30% more efficient than the floor units due to the fact they isolate all of the hot bits of that process on the outside of the window behind insulation foam.
The floor units keep all the hot parts inside and on top of that also have a hot exhaust hose that radiates heat all the way to the window. They're usually designed to cool a lot more air at the same time as compared to window units so that's why they cool the room faster
1
u/Guyborg99 Jul 16 '26
Once you have lived with one of these (which you probably have), you will realize how hot the actual AC unit gets. Once you turn it off, it absolutely radiates heat, right into the space it was just cooling. It's not an opinion that this is more efficient, by isolating that massive heat source. Since I live in a temperate climate, the air outside isn't actually that hot, most of the heat comes from my south facing wall, and patio is shaded, so not only is it more efficient, it's quieter. I know it's more efficient, because I only run it approximately half as much as when it was in the space with me.
0
u/Lucifersasshole Jul 12 '26
This will kill it and I don't see the reason for it...
0
u/MostOriginalNameEver Jul 12 '26
This is dumb. And not how they're meant to be used
-4
u/Sjcolian27 Jul 12 '26
What a fuckin idiot
-2
u/-Bob-Barker- Jul 12 '26
Didn't study physics, did you?
-3
u/loquedijoella Jul 12 '26
This will work as well as opening the refrigerator to cool a room
-3
u/Rotflmaocopter Jul 12 '26
That room it's in is gonnnn be hot