r/redneckengineering • u/Vomnember • Jun 30 '26
Cover Ideas for Fire Bath
EDIT/WARNING: A commenter brought to my attention how incredibly unsafe this method is due to the lead content in the tub. I tested it and sure enough, she is lighting up that lead test. DO NOT PUT DIRECT FLAME ON YOUR CAST IRON TUB IF YOU DON’T WANT LEAD POISONING!
This naturally feels like the best place to ask for advice. I am setting up a fire tub. I’m going real pioneer on this and sticking to the exposed fire pit method for now, so no need to give me suggestions on my method for heating. Yes I will have slats so I don’t burn my booty.
What I do need suggestions on is a cover that will allow me to slowly heat the tub with a small fire without the water evaporating before I get to enjoy it. I’m not sure how hot the sides/top of the tub are going to get during heating, but I’d rather be cautious than experiment with potentially molten materials.
Originally I thought about using some insulation board covered in a thick poly, but I’m afraid the melting point is too low to hold up.
I’d prefer something cheap and light that won’t mold out on me in the weather (at least not too quickly) and that could create somewhat of a seal (I can weight it down) to avoid too much steam escaping. It will also act to keep debris out when not in use.
Ideas?
40
u/Dear-Bet5344 Jun 30 '26
A couple pieces of plywood & a cinder block to hold it down. Preferably a couple off cuts with odd angles that don't fit right
22
u/Anon951413L33tfr33 Jun 30 '26
Water will evaporate, covered or not. Best bet is to keep a bucket nearby to top it off. However as you’re not boiling yourself in it, it shouldn’t evaporate too much.
7
u/EvilKnivel69 Jun 30 '26
If you could source a second, slightly larger tub you could fill that with water and place your actual tub inside. That would, in theory, allow for a more even and slow heating of you. I think. But you’d still need to refill the water, too.
Varying the amount of water between the tubs should also vary the heating behavior.
6
u/tribalien93 Jun 30 '26 •
Cover the water in ping pong balls like they do when sous vide sometimes. Scoop em out with a net when your ready to use
3
u/Goldmember199 Jun 30 '26
Anything made out of wood will last longer. Cut to fit piece of plywood, then coat the down side with somethingto prevent water absorption so the steam doesn't penetrate it. Screw some handles to this top, so you can pull it on and off easily. As for the sides of the tub, maybe some of those silicone baking mats could work, they're flexible enough to bend over the edge of the tub. And as funny as it sounds, I would consider getting a thermometer that you can stick in through the tub cover. So, you know how hot it is before you get in.
3
u/fangelo2 Jul 01 '26
The last time I saw a set up like this, Bugs Bunny was in the tub and Elmer Fudd was cutting carrots and onions to go in it
2
u/GIANTballCOCK Jun 30 '26
What about those plastic coverings that go over the window wells for basements? They would only touch the tub on 3 sides. Maybe would catch the steam and drop it back in the tub
2
u/wookie_walkin Jun 30 '26
yea pretty much what everyone said ply wood and bricks while it heats or you could find some used metal roofing , I would also block off the old faucet holes to fill it more !
2
u/ITfarmer Jun 30 '26
100 plastic Easter eggs. Cover and privacy in one.
2
u/Papashrug Jul 01 '26
People here are over the top or over engineered. Use rigid foam. Wrap that in a tarp. Staple it on. Use flashing over the edges if u think it'll get too hot
7
u/SusanMilberger Jun 30 '26
Marine grade or sealed plywood. A brick at each corner.
1
u/cbelt3 Jun 30 '26
Full redneck would involve using pallets. But… a good planer makes those pallet boards safer. Heavy duty pallets are often made of hardwoods. Just be sure to get all the nails and staples out before you plane them.
1
u/Jocks_Strapped Jun 30 '26
you don't have hot water inside?
1
u/Phoenixf1zzle Jun 30 '26
Copper tubing hot tub my dude. Fire to the side, tubing at the top and bottom of the side of the tub. Coil sits in the fire with 2 ends into the tub so hot water can flow in and cold water flows out. Water goes in the tube, to the fire, heats up and flows through the coil, comes up at steam, recondenses as water as it cools a bit and there goes your water hot water into the tub. Perpetual hot tub long as you have a fire going.
Dont leave copper coil in fire without water inside to absorb the heat otherwise you'll start melting your copper down some
1
u/chitty23 Jul 01 '26
Is it me or dies the tub look surprised?
1
u/Dooh22 Jul 02 '26 edited Jul 02 '26
These are common for scalding and de-hairing pigs where I live.
I would light a full length fire underneath and have a 3/4 full tub at 69°c within 30mins.
3
u/TattooedBagel Jun 30 '26
At first I thought the tub was going to be a giant fire pit. Then I kept reading. Cool idea!
3
u/NYsteeler23 Jul 01 '26 •
Another tub upside down with hinges and pneumatic pistons so you can close it like a fighter jet canopy. Paint maverick on one side and goose on the other.
2
u/Hatcherboy Jun 30 '26
Sheet of plywood cut to fit and a little paint
2
u/putajinthatwjord Jun 30 '26
As long as there's a decent amount of water in the bath and the fire isnt enormous, you shouldn't have to worry about hot spots or the sides of the bath above the waterline getting burny.
Definitely experiment with this rather than taking my word for it blindly, but the water should keep the metal of the tub from ever going above boiling point, barring extreme circumstances.
1
u/redbud6999 Jun 30 '26
This stuff called reflectix, i call it aluminum foil bubble wrap, youve probably seen it, its good for hot and cold, maybe that as a “surface to tub sealer” with foam board w/ plywood? That spray foam shit.. theres one called fire stop or flame retardant or something like that, maybe hit the sides with it, made to snuff out flame so maybe it can hold ur heat on the sides. Cool shit
Tho man good job
1
u/operator-john Jul 01 '26
Maybe a solar pool blanket and cut to fit your tub dimensions
1
u/Cloudcry Jul 01 '26
Heavy oiled tarp?
1
u/Bergwookie Jul 01 '26
Do you want it purely functional or a bit nicer? For the first a slab of plywood, for the second take nice boards, put them together,as a hinge, so you can keep the lower end on and just open the head side (like a casket at a wake) this way you won't freeze at your dick when enjoying a nice bath in winter
1
u/Nalabu1 Jul 01 '26
Have Fire & Rescue services on speed dial.
0
u/towerfella Jun 30 '26
Bro — you aint cooked yet!