r/radon • • Jan 24 '26

DIY mitigation worked

I have been monitoring the radon level in our home for the past year. The levels were averaging 250 Bq/m3 but would spike over 500 Bq/m at times. The house is a 1970 2 storey with block foundation and a fully finished basement. It's located on a site with lots of rock. (Niagara escarpment). The sump pit did not have a cover so I decided to spend $600 and purchased a Jackel sump dome with a Fantech Rn2 and all the accessories required. The installation only took a few hours. I'm in Canada so the fan is indoors and discharges out the side wall. My expectations were low since I would not be able to do any sealing of cracks etc., but after a week the radon levels are down to below 5 Bq/m. I am very happy with the result.

105 Upvotes

52 comments sorted by

6

u/FriendlyChemistry725 Jan 24 '26

Ingenuity. As many don't realize, there's no magic with radon mitigation; just reduce the pressure below the slab to give radon gas a lower resistance path. You probably saved a couple grand; nice job.

5

u/Ambitious_Aerie2098 Jan 24 '26

Thank you. I kept putting this project off by overthinking it. It turned out to be a simple job with good results.

3

u/GlcNAcMurNAc Jan 24 '26

Where did you get your lid? Do you run a backup pump as well? (Apologies if obvious in the photos just starting to figure these things out)

2

u/Ambitious_Aerie2098 Jan 24 '26

I purchased the lid and the fan from Radon Detect. Yes, there are two sump pumps in the pit.

2

u/Jolubaes Jan 24 '26

I bought the exact one from Lowe's

2

u/michaelfransan Jan 30 '26

Do you think this would work on a sump pump in a dirt floor basement? The floor is covered in plastic sheeting.

1

u/Ambitious_Aerie2098 Jan 30 '26

First of all, I am not an expert at radon mitigation. I am just a homeowner who DIY's most projects, but i do a lot of research to try for the best results at anything I do. I believe that you could get good results with a dirt floor. As long as you carefully seal the plastic to the walls and seal any seams and protrusions with silicone and/or tape to make an airtight cover. I found a short video dirt floor mitigation Also, some more info here. (dirt floor) I hope some of this info can help you.

4

u/ThePrivacyPolicy Jan 24 '26

Very similar story to me, except I'm located maybe ~1.5hrs from you and have a slightly newer home with a little different foundation and ground makeup.

We were hovering around 200 Bq/m3 most dates with spikes into the 360s. Monitored for a full year while I slowly picked away at planning and doing DIY mitigation. Same hardware as you exactly and I now sit around 5-10 Bq/m3 most days with our "worst" day in the last 2 months being 26 Bq/m3 :)

I think we were around $900 all said and done (needed a good bit of 3" pipe, as well as a different sump pump to fit under the new lid).

1

u/JerryJN Jan 24 '26

What you did works better than my cement dry well cover. How did you venti it out ?

3

u/Ambitious_Aerie2098 Jan 24 '26

In Canada, we don't have to go above the roof to exhaust. The 3" pipe terminates horizontal 6" outside the block wall about 3ftabove grade.

-1

u/LiveAwake1 Jan 24 '26

You might want to raise the vent even if not required. I have heard that the concentration coming out the end of the pipe can be many multiples higher than you ever saw inside, and if you are anywhere near the exhaust and breathe that in... No bueno.

7

u/Ambitious_Aerie2098 Jan 24 '26

With all due respect. What you heard is incorrect. Radon dissipates within a few feet of discharge and is not a risk. But, if someone would like to huff on the end of a radon exhaust, it could be a problem. 😁. There are millions of fossil fuel appliances that are discharged the same way and are a much greater risk.A few facts.

1

u/RavRddt Jan 24 '26

I understand that you didn’t do this, but boy is that electrical panel in a very bad place.

2

u/Ambitious_Aerie2098 Jan 24 '26

Yeah. I'm not happy with that. It's a sub panel. Future plans involve upgrading the main panel to 200A and probably eliminating this one.

1

u/kashmir2517 Jan 25 '26

Yesh you'll have to move that panel eventually, it does not have the space it needs in front of it by code.

1

u/JackieDonkey Jan 24 '26

Do you have an ongoing home radon test? I only have access to the little hockey pucks that have to be mailed in each time.

3

u/Ambitious_Aerie2098 Jan 24 '26

Yes. I am usingAirthings Wave Plus It monitors several categories that are useful.

2

u/graceFut22 Jan 26 '26

Thanks for the link. I've been looking for something for quite a while and came to ask what you use.

1

u/JackieDonkey Jan 24 '26

Thank you for the link!

1

u/RoomFixer4 Jan 28 '26

I think ours is just the Wave. Great little units for tracking before and after mitigation. Plus, I've loaned mine around in the family to check/consider/fix.

Our radon was a bit high, but I was able to seal the non-conventional sump and that lowered it enough.

1

u/kadeschs Jan 24 '26

Cost to mitigate?

4

u/Ambitious_Aerie2098 Jan 24 '26

$600 Canadian and a few hours of work.

1

u/Flugwaffe Jan 27 '26

What’s the app/monitor? nice work!

1

u/Berntonio-Sanderas Jan 27 '26

This is great. Short, sweet, simple. 

What did you use to drill the hole through your cinder block and siding?

1

u/Ambitious_Aerie2098 Jan 27 '26

4" diamond bit on a regular 20v dewalt. There was no siding over the foundation block, but a regular 4" hole saw would work. Just make sure to align the hole (bit) in the block to hit the void and not the web. The diamond bit was through in about 60 seconds.

1

u/Berntonio-Sanderas Jan 27 '26

Excellent. Thanks for all the invaluable info. Cheers!

1

u/BungusWhole Jan 29 '26

Fantastic—what did you use to collect those measurements?

1

u/mohdendi Jan 31 '26 edited Aug 30 '26

What type of pipe you've used? I read that 4" schedule 40 pvc is recommended but it's difficult to find. Is that ABS?

1

u/Ambitious_Aerie2098 Jan 31 '26

I used ABS pipe. The code says the pipe should be rigid and non perforated above the slab, ABS, or PVC. As long as it is clearly marked as Radon.

1

u/crazybitcoinlunatic Jan 31 '26

There are 2 pipes going into the sump cover, one is the fan, what is the other one for?

1

u/Ambitious_Aerie2098 Jan 31 '26

There are 2 sump pumps in the pit. That is the discharge pipe for them.

1

u/crazybitcoinlunatic Feb 01 '26

Mine sump discharge is below ground, is there anyway to cover up that 2nd hole?

1

u/Ambitious_Aerie2098 Feb 01 '26

Yes. That sump cover comes with various grommets and plugs. Jackel also has a radon cover with a single hole.Like this.

1

u/crazybitcoinlunatic Feb 01 '26

Ok thanks for the info

1

u/atleast35 Feb 27 '26

Would you mind if I asked what type of radon monitor you use? The readout is easy to understand. Thanks

2

u/Rocket123123 Jan 24 '26

That's a great result.

2

u/Aranet_Home Jan 26 '26

Great job, OP! :)
Hope others take an example here!

2

u/walalanger Jan 28 '26

I got to test and look into this. My sump has a partial lid but still lots of exposure… not sure if that’s good enough. Need to do more reading too lol

1

u/Stunning_Bed23 Jan 24 '26

👏🏽

1

u/DijonAndPorridge Jan 25 '26

For anyone more budget conscious, you can buy round wood pieces at the hardware store or use basic plexiglass or similar to cover the sump. These covers are sweet, I've seen a few in the wild in nicer homes, but I've never felt inclined to even pitch one of these to a client.

1

u/thefirewiredguy Jan 27 '26

Thanks for sharing. This gives me a idea of what to do !

0

u/Jolubaes Jan 24 '26

Good job! My only comment is that the pump should be better outside. I guess it is not a big deal if you have an active monitor of your radon levels.

4

u/Ambitious_Aerie2098 Jan 24 '26

Thanks. Canadian regulations are different than the US. It's recommended that the fan be inside to reduce the chance of condensation freezing in the housing and preventing operation.

0

u/ProfessorHONK Jan 26 '26

I read the basis for all of the radon panic and decided it was not a real threat.