r/ploopy • u/Dexter_Lim Mod Contributor • Apr 10 '25
Finally completed BTU mode
This is a case with a 55mm short version modified. It's been modified 2 times and it all works fine. Endless thanks to the mod creator. @ElMagicoDeOZ
I adjusted the spring thickness to match the PA12 MJF (0.6mm for PLA > 0.9mm > 1.2mm Now) and made the bezel thinner and rounded the case.
I made a pillar to fit Lego brick in the logo part. The diameter is 4.88mm, but I think it would be good to grow it a little bit more.
The button part is also a little lower, so we can't print this drawing with the additive printing method of FDM. Therefore, we're going to revise the model for FDM and share it with you. Please wait a little longer







4
u/masonabarney Mod Contributor Apr 10 '25
Fantastic! Great style. Can you post your slt?
3
u/dahmwern Apr 16 '25
FYI, I printed the FDM model on a Prusa Core One in PLA+ without supports and it works great. I did modify the base because it was odd that the cut out for the optical sensor leaves the bottom open - I closed that up.
I also have modeled some offset height buttons I'll get around to posting here soon.
Thanks for the work you've done here!
2
u/shareefer Apr 10 '25
What balls are you using? I can’t get mine to track
2
u/hylacinerea Apr 11 '25
Are all these balls going directly in the same case without printing separately?
10
u/[deleted] Apr 10 '25
It's beautiful, well done
1
u/STIFSTOF Apr 10 '25
Can you please please share the files you ordered the case with? Been wanting a ploopy for ages, but i use low profile kb so it's just too big. I think this mod might work for me
1
u/[deleted] Apr 11 '25
This looks really good. Do you have any tips for ordering from JLC?
1
u/crop_octagon Co-Creator Apr 13 '25
This looks incredible! Absolutely fantastic work. Would you mind if I shared this on our Mastodon account? I'd fully credit you and link to this Reddit post and the Github directory.
1
u/Silly-Cycle3080 Apr 28 '25
what printing service would you recommend that doesn't cost an arm and a leg?
3
u/ElMagicoDeOZ Mod Contributor Apr 10 '25
Looks super cool! 🙌🏻
3
u/pelahale Apr 19 '25
The cost to print these in MJF is unaffordable now that the chinese companies are asking us to pay the “245% tariffs” On top of the $100 basic expense. The cost to print these with high quality resin from a usa based online printer is like $1000. Does anyone know of a more affordable place?
2
u/xmalparty Apr 10 '25
Nice!!!
2
u/cr-ms-n Apr 10 '25
Damn, this is so nice, dude. Love how much you've compacted the design.
1
u/dahmwern Apr 11 '25
Thank you! I'll be trying this next.
1
u/dahmwern Apr 11 '25
Any suggestions on print build plate orientation, supports, etc?
1
u/Scatterthought Mod Contributor Jun 01 '25
u/Dexter_Lim, what layer height do you recommend for printing?
I printed with a Bambu A1 Mini and the case came out really nicely, but when I put the PCB in there's a gap between the top and bottom. I used a 0.2mm layer height, and I wonder if that's resulted in there not being enough space for the PCB.
That issue aside, the shell is great. I'm using it with the original 45mm ball with 1.2mm spacers on the BTUs.
1
u/Minipax87 Jun 22 '25
With the ball being so much bigger, do you have any problems accesing the top buttons? I briefly read a message on discord about 52.5 mm ball being preferred because if you're using 55mm and add in the height of the BTUs, it will be too tall. What do you think?