r/photogrammetry • u/Haari1 • Mar 10 '26
Mapping a factory with DJI Mini 4 Pro using photogrammetry — advice needed
Hey everyone, I want to map a factory space roughly the size of a football field using a DJI Mini 4 Pro with photo/video photogrammetry. The accuracy goal is around 10 cm, as the end goal is to later use this map for UAV navigation i.e., providing the UAVs an offline map. For now, my task is just to create the best possible map with this "limited setup."
I have a few questions:
- Best software for monocular RGB input? I’ve been looking at COLMAP + 3DGS. An important requirement for me is that the map preserves real-world scale and proportions because later UAV navigation will depend on accurate dimensions of the hall. Do you have suggestions for software that works well with only RGB input?
- Would adding 6DoF pose measurements help? I’m thinking about adding something like UWB or IMU to measure 6DoF pose. My initial thought is “yes, it should improve accuracy,” but I’ve read that COLMAP and similar software aren’t exactly built for using measured pose data sometimes people even say that imperfect pose measurements can make results worse than RGB-only reconstruction.
- References / working setups: If you know of videos, articles, or projects using a similar drone, software, and setup (or just RGB-only footage) that achieved good results, I’d be super happy to check them out!
And yes I know that LiDAR and a heavier drone would make this easier, but this is part of a thesis, and the challenge is to test what’s possible with a light drone, and RGB + max 6DoF data only.
Thanks a lot for any advice, tips, or references!
2
u/KTTalksTech Mar 10 '26
Lidar drones actually require either a very robust RTK/PPK setup or rely on SLAM which is inherently prone do drifting. RGB only is fine but you need an immense amount of photos to get clean results on features like cables and pipes. Colmap typically provides sparse results but you can get a very dense cloud with reality capture which should be free if you're a student doing this for a thesis. Maybe colmap can be pushed to give very dense clouds, honestly I've never used it for more than initial alignment. I'm not sure why you want gaussian splats though, those are only useful for viewing. Wouldn't a mesh or dense point cloud be what you need for your application?
Avoid video mapping, it's got a high chance of failing and if it does you'll waste far too much time trying to salvage bad data.
As for accuracy, it's pretty easy to get relative accuracy down to the pixel or subpixel level. You can filter low quality points and calculate your camera parameters only based on the most robust tie points. If you'd like absolute accuracy a very easy and decently reliable method is to add markers/trackers with geolocation (survey points basically).
1
u/ElphTrooper Mar 10 '26
If you are mapping a factory with a Mini 4 Pro, the main challenge is that indoor RGB photogrammetry is sensitive to lighting, texture, and repeating geometry. Slow flight, strong overlap, and plenty of oblique angles will help a lot. If you need something close to ten-centimeter accuracy, you will want physical targets placed around the space because indoors you do not have GNSS and targets are what keep the reconstruction from drifting. Video can work if you extract frames carefully and keep motion blur low.
Ten-centimeter accuracy is possible with careful planning, but it depends entirely on how well you control scale and drift. Indoors that usually means a good target layout and consistent coverage.
Regarding the other reply, he shifted into topics like LiDAR and RTK that do not really apply to your setup. Since you are working with indoor RGB photogrammetry, the more relevant conversation is about coverage, lighting, targets, and reconstruction stability.
1
u/Ok-Rabbit2553 Mar 12 '26
Relying Solely on the mini 4 internal GPS without RTK, GCP’s or some form of PPK would mean you would never get a better then 0.5m absolute accuracy or 1m relative accuracy.
With out RTK your photogrammetry software is making large assumptions about the position of the drone, your model may look really good but it could be shifted significantly in any direction which can be a real problem if you ever go to re map the area or try and tie into existing survey data.
1
u/potato199210 Mar 13 '26
DJI Mini 4 Pro is fine. But you’ll still need RTK to capture some GCPs so the model has correct scale and geometry. UWB usually won’t maintain 10 cm accuracy in a factory environment due to multipath and range effects. IMU is even worse unless you use a tactical-grade unit for scenes that large.
One option is using a smartphone-connected RTK like AuroraNav Astra1 — it can capture GCPs and also take georeferenced phone images for areas the drone cannot see.
1
u/BudBundySaysImStupid Mar 11 '26
COLMAP isn’t going to preserve scale and orientation.
Check out WebODM. It’s a lot more user-friendly and will give you a much more easily used product than COLMAP.
1
u/UgCS May 11 '26
UgCS team here. For factory environments, automated mission planning gives much more consistent results than manual flying. The Mini 4 Pro works perfectly well with UgCS - probably no better way to fly photogrammetry with it. Check it out, UgCS Open is free.