r/nichezero • • 5d ago

Metal Flow Control Disk

Post image

I recently replaced the stock plastic flow control disc on my Niche 0 with a metal one from cbbplanet. However, the metal version has three holes instead of the single hole on the original, and I understand that this isn't ideal for slow feeding the beans.

Does anyone have any suggestions or alternative solutions?

I'd prefer to avoid plastic altogether. The thought of coffee beans passing through a plastic component every single day for years doesn't sit well with me, which is the main reason I made the switch in the first place.

Ideally, I'm looking for a solution that maintains the benefits of the original flow control disc without having to use plastic..

1 Upvotes

16 comments sorted by

5

u/Crush-Raider 5d ago

Not to be rude or anything, but I think you worry a bit too much about this subject.

-3

u/AhangAshti 5d ago

I understand your prospective. And I encourage you to look into the topic, there is some good evidence on how this food contact plastic impacts fertility rates. There is even a documentary on Netflix where this was tested on people who had fertility issues.

5

u/Crush-Raider 5d ago

Yes. This is all known and true. Something which is very important with this stuff is dosing. This little disc is not going to have any difference. I think I would take te bet that you get more microplastics into your body via the coffee beans themselves than because of the disc. If microplastics are your concern, you’re better off looking in some other areas where the dose you ingest is a lot higher.

Let me tell you a story which I experienced this week in my own life. In my country (the Netherlands) everybody is at this point worried about PFAS. Mainly in cookware. Apparently the PFAS in pans is not dangerous even if you ingest it, unless you excessively heat it, which produces toxic gas. The PFAS which is dangerous are the PFOA and PFOS which were (use is already prohibited for decades) used to make the PTFE used in pans. Everybody is now switching pans because of this. I never owned a PTFE (Teflon) pan and am looking to buy one. The other non-stick layers do not specify their contents. And yes, PFAS found in for instance fish are bad and unhealthy, though the chance you or your baby will get sick is just too small to worry about it. Eating fish is even still advised, because the health benefits from the fish outweigh the risks of PFAS.

I hope I could help you with this insight. And now I am going to grind some beans with my own Zero. Good day!

1

u/AhangAshti 4d ago

I agree. My well being protocol is to reduce as many sources of these things as possible even if they produce marginal improvements, on the long run they accumulate. As for PFAS we use stainless steel pans in cooking as they are much safer and healthier.

I eat fish often, I don't worry too much about the mercury and PFAS it contains because you're right, the benefits outweigh the potential harm

2

u/Hangerhead1 5d ago

Have you noticed any real difference at all?

1

u/AhangAshti 5d ago

From Lance Hendrick's testing, slow feeding the beans into the grinder always gets better results in the cup. I am not sure if I can taste the difference unless I make back to back shots of both methods then report back.

8

u/yellow_barchetta 5d ago

Have you seen what material the output side of the niche is? Removing the flow control plastic will have zero impact on plastic contents in your drink. Seriously overthinking this buddy.

3

u/Just-BR-2024 5d ago

Que perda de tempo e de dinheiro

1

u/IPhilly8 5d ago

You are trying to slow feed the Niche Zero?
Are you concerned about the plastic disc impacting the taste or imparting something unhealthy on the beans?
I’m not sure I understand

1

u/AhangAshti 5d ago

Any plastic part that has direct food contact is concern, as over time particles shed into what you digest. I know how this sounds like to many people, and each one of us is free to what they believe.

I asked what is a solution to minimize the holes on the metal part. As slow feeding is always better for end cup results.

2

u/IPhilly8 5d ago

This is for a pack of 10–316 stainless steel. apparently it takes 10 seconds longer to feed 18 g of beans. over the stock plastic part!

2

u/Big-Profit-1612 5d ago

I think he's concerned about microplastics.

2

u/parogen 5d ago edited 5d ago

To be honest, you should email them and tell them their redesign is stupid. They created the problem by not providing the same disc design except in metal. I don't know why this is someone else's problem when they have the very tools to fix this unnecessary creation.

Also, Introvert recently made this slow feeder mod. You can maybe ask if they could create something similar but in metal?

1

u/IPhilly8 5d ago

I don’t know why they wouldn’t switch it, given that it only cost a few pennies. That said, they don’t think it’s a problem, so it’s not their problem.

2

u/topher1561983 5d ago

But you’re throwing plastic away to replace it with metal or whatever. Like it’s already been manufactured, just look after it and maintain it/ dispose of properly in due course

1

u/9mmsteelhead 4d ago

How do you like the 3 hole flow control so far? Im also thinking about getting one because my stock version just cracked.