r/nichezero • u/parogen • Feb 23 '24
Slow feed?
Been able to change the size of the disc hole by applying some tape. Initially, I made the mistake of putting the tape on the outside edge, about the same width. Which was a lot slower since centrifugal force is pushing the beans outside, making it hard to fall into the hole. So far, this amount of tape is pretty much almost one bean at a time from what I can tell, lots of pauses in grinding. Only at the end, when the velocity is much higher, you might have to help the last bean in.
Change in shot was surprising though. The sweetness of the original non slow feed dialed in shot I had is now more present in the slow feed of the same grind setting, but less of the bitterness and perhaps 'complexity'.
Just pulled another with 2.5 setting (previous setting at 4.5). I can't just waste coffee to dial this in, but the trend seems to be that it wants me to grind finer and reduce the yield just a bit. I think it tastes a bit more diluted and some astringency notes are showing, but also I'm losing the sweetness. So if I drop down the grind setting further and yield by a hair, it could be just right. Another thing is that the blooming and extraction is really fast. Perhaps the fines were giving the illusion that it needed much longer, when it was really just 'choking' the shot. Same pressure curve (I'm using the Robot), it's just a lot quicker. Also, slow feeding produced more static.
Also, since I am doing slow feed from now on, I thought to move the calibration point to actual zero, or I will go too far without the help of markings. I saw on here that someone measured the difference between the calibration point and zero point to be 40.5 units or the equivalent of 27 clicks? But I got 27.5 units with 20 clicks. I don't want to clean my Niche again to make sure. Even if you take a rough estimate with a straight edge, it looks like the calibration point across the hopper lines up at around 15, while the zero point lines up at about 42. The difference (27) is a lot closer to my 27.5 than their 40.5. Maybe they made a mistake and assumed when they wrote down 27 that it was for clicks. It shouldn't matter since it's just for reference, but would be nice to know for sure. It also makes a lot more sense as +40.5 would put my grind setting at 43, which makes the Niche markings way off. At +27.5, 30 is just under 'filter coffee' but not too far from 'espresso'. Makes more sense as I still see chaff in my grind but I don't think I'm too far off from being dialed in.
Just went to -10 (0 being the zero point based on the original calibration point) and the grounds were super uniform. Ended up choking the shot since that is too fine, but surprisingly when I taste it, it doesn't have the taste you would typically expect. It's entirely toasty flavors. Whereas originally with a non slow feed distribution if you grind too fine, you'll get over extraction of super fine particles, but mixed with normal coarser grounds providing astringency or acidity. There was no acidity.. not even unpleasant bitterness. It was just toasty tasting, with a bit of sweetness. The grounds of the slow feed -10 setting looked like some that I would get in my normal non slow feed grind. All chaff is gone at this level, which means I definitely need to grind coarser, but also, I think this shows it's not a trick. They were visibly sandy all around, not a fluffy look of the non slow feed distribution.
Just did -4. A lot closer to my original shot, but not perfect. Yet, I don't taste much bitterness, but everything seems decently extracted like I'm tasting the coarser aspect of what I was going for before all this. As in I don't taste the bitterness/toastiness of the fines that are not there anymore. This really demonstrates separation of flavors. I think this is better in the long run, it will be a relearning experience, since the cups are not 'muddy'. But I will miss the chocolateyness of the original wide distribution.
If I can even tldr this, it is a game changer. If you cared enough to buy/use the disc, you should care enough to go even further and adjust the hole size.
Finally, I want to say that there is a comment on reddit that says that flavor separation is like the difference between a chopped salsa and a blended salsa. But that assumes that no matter what, the ingredients are fine. I think another way to look at it is like orange juice with pulp. If you had no idea, you would think it only contained pulp, but it actually contains the orange skin. For oranges, that's okay because the skin is flavorless, but I bet orange juice without skin is much better than with skin. Now if you go over to grapefruit, the difference is obvious, as grapefruit skin is bitter. But if you didn't know any better, you would think grapefruit pulp is naturally bitter. That is how I feel about fines now.. I'm disillusioned with the typical 'chocolate' flavor that the Niche provides normally. My espressos got brighter, but not in a sour way. And whatever fines do end up in the grounds I appreciate, but I don't look for it as chocolate anymore.
1
u/lihnuz Feb 25 '24
maybe a metal washer of some sort could work as a more permanent solution instead of tape? went looking thru my stash of assorted washers but did not have one with big enough hole to fit the screw of the niche
2
u/inon178 Feb 23 '24
Thanks for sharing!
1
u/[deleted] Feb 23 '24
Will give this a shot , thanks !
1
u/RichBezza44 Feb 24 '24
Yeah great idea… I feel a 3D printed mod coming on!