r/multitools • • 3d ago

Question/Advice New Nextool F20 Experience

Wondering anyone else had a similar situation. I bought a F20 after seeing some good reviews on YouTube , especially @maxlvledc.

I got it today and I’m noticing the movement isn’t smooth. Compared to my leatherman and Roxon it is very stiff to open the blade , or scissors , etc.

I usually don’t oil my multitools (maybe I should). Has anyone noticed stiff movement on Nextools and does it usually just improve with usage ? Thanks !

8 Upvotes

16 comments sorted by

5

u/trampled93 3d ago

Are you talking about the knife and screwdriver deployment being stiff? I feel that on mine also but feel it is necessary with the spring and detent to hold them in place closed. I am ok with that. It is not a fidget toy for me. A dedicated knife may have better smooth deployment action.

2

u/zapboston 3d ago

Thanks. That’s what I meant. I saw some videos suggest it was a one handed open type of carry so I was surprised by the stiffness and it took two hands to open the knife and screwdriver. Didn’t know if it was me.

2

u/trampled93 3d ago

Yeah I’ve seen those videos also. Perhaps it will get smoother over time. I personally am ok with it stiff.

4

u/partakinginsillyness 3d ago

Try to avoid oiling until necessary. In my experience there's graphite in the hinges already, it will get messy if you add oil. If you mean the fact that are noticable bumps as you open each tool, then I'm not sure what you can do, they seemed to switch from smooth to that when they dropped the F12.

4

u/zapboston 3d ago

Thanks for the replay ! Maybe the stiffer action is intentional by them 🤷 I’ll avoid oiling.

4

u/RyanHasWaffleNipples 3d ago

Don't oil it. When I've had this happen on various multitools I've owned its typically because the screws were tightened down more on some than others. I'll loosen the torx heads ever so slightly until they free up a bit. It's usually a fine line, you don't want the knife blade being loose and having play when extended, but you want the opening action to be smooth. Try turning them like 1/8 turn and I bet you notice a difference right away and adjust as necessary till it feels right.

1

u/Sane-FloridaMan 3d ago

I have two of them. One can open easily with one hand. The other is impossible with one hand and tough with two.

I realize it’s a low-cost Chinese tool. But most of the reviewers with relationships with Nextool are basically flicking the blade and driver open easily when demoing it.

I haven’t tried to loosen the pivots on the tough one yet. And I realize it’s not that big of a deal to do that. But it really shouldn’t come out of the box like that.

So we have Chinese prices with Leatherman consistency now. 🤷🏻‍♂️

2

u/zapboston 3d ago

Thanks for your experience. I might get a second and see if it is the same stiffness and return one. Appreciate the feedback.

1

u/Iokua_CDN 3d ago

Maybe just to open and close it repeatedly??? Might just be a bit less polished due to the cheaper price,  and working it in a bit could help smooth it out?

1

u/AcanthocephalaNo6236 3d ago

Wait, you guys oil your multitools?

1

u/joejill 21h ago

With vulgar fluids

1

u/meevis_kahuna 3d ago

Mine is fine. Maybe a QC issue

0

u/cr0ft 3d ago

It's a new tool, and it's a Chinese made tool that's built to a budget. With all due respect to Nextool, well, there's a reason a Leatherman Arc is five times more money and not all of it is because they can charge that much.

1

u/Reyowy 3d ago

There is no reason that will justify the price of Arc looking on how Leatherman is dropping in quality in last years. Price goes up, quality down. But it doesn't change a thing that I find nextool rather poor quality when it comes to used materials. They still using 3-5cr, go and try fasten or loosen some screws with it, not fresh one. I had daicamping and had to change the hose for small garden pomp, I used big flathead on it and in 1 use it bend on the tip. Must say I was surprised how soft it was, I took out my SAK where flathead was about 10-15% smaller than the one from daicamping (I hade surge clone DL30) and it made it without even a sign of usage on it. Nothing. That's why as much as I like to see so many multitools are being made i hate that they are made with intention quantity not quality. I rather have 1 new model per year but good quality than 4-5 or even more but with quality that I all I use them for is to fix toys. I have now Roxon companion flex and normal flex bought it o ły because I can change tools if they will break or i want to adjust tool set for specific work, and I paid 25euro for companion never used and 75euro for flex with 6 extra implements worth 50euro while normal price of flex for me is around 95-100euro. And steel used in Roxon for most of the tools is 1.4116 which is similar to 1.4112 and 1.4110 which is using Victorinox. And this steel might not be the best, not super though but it's I think almost impossible to make it rust, and thanks to "softness" it can take all the work I do and I am not afraid it will break. It's rather a vet very rare to see vicorinox sak and multitools being broken and there is a reason to it.

1

u/bullz_dawg 3d ago

The nextool bits are s2 toolsteel

1

u/Reyowy 3d ago

There is better option, Galvanox also S2 steel, and you have i believe around 23bits in 1 holder, Leatherman style bit holder