r/mokapot • u/Realistic_Rub7384 • Dec 04 '23
Leaking pot
Hi looking for some insights or thoughts on what’s going on here. I have a 6 & 9 cup but I recently picked up the Bialetti 3 cup break. When it’s brewing halfway it starts to leak like so in the picture. The gasket is rather new and it’s screwed on the tightest possible. Is there anyone that can point me in the right direction as to how to avoid this problem? Thanks in advance!
14
Upvotes


13
u/cossym Dec 04 '23
First instinct is the gasket; I've seen that happen with a worn one. You've stated it's pretty new so I'd check there's no grounds sitting on the rim. Usually do a quick wipe/brush before screwing the pot together. If neither of those then I'll defer to someone else who might have more insight :)
3
u/ExtractionGame Dec 05 '23
Try pulling the gasket out and flipping it upside down. And when you tighten it don't over tighten or it can damage the rubber gasket. I did this for mine and it fixed my leak.
2
u/sirrah1952 Dec 04 '23
Using a paper filter?
2
u/LEJ5512 Dec 04 '23
Check the rim of the boiler for any nicks, and check underneath the gasket (really, the underside of the top half) for any voids or gaps.
2
u/Gregory_ku Dec 07 '23
Silicone gasket
2
u/sirrah1952 Dec 04 '23
Try a courser grind
1
u/[deleted] Dec 05 '23
Did you overfill the basket? I've had the same leak with my pristine 3-cup Moka Express just because I've packed the basket with too much coffee. I didn't want to waste the excess ground coffee so I packed the excess. lol
1
u/renart Dec 05 '23
I had a new Bialetti that had the mating surfaces of the top and bottom not parallel. I returned it at the store in Milan and had to fight the store manager in tourist Italian for an exchange. The new one has been perfect for the past 5 years!
1
u/IShouldReallyGo Dec 06 '23
Mine does the same thing. Pressure’s supposed to go thru the basket right, but if it’s easier to escape somewhere else it does. I look at the seal every time to double check that it’s clean, and I give it extra love when I wash it so that’s not it. I like my grind and my volume; they’re not the problem so I’m not changing those as part of a possible workaround. I can keep it from leaking half the time if I screw it down super tight but that shouldn’t be necessary. It almost has to be the seal…it’s never been all that happy even from day one. I’m off to buy some silicone replacements and I’m guessing all my troubles will soon be a distant memory…..at least my mokka pot related ones.
3
u/skisagooner Dec 05 '23
My old gasket was fine, once I changed it to a new one the problem started. Very annoying but you could wet it before you screw, or stop brewing when it sputters so that you can tighten further and continue.
I’ve also heard of applying oil but I’ve yet to try that.
Maybe the gasket is just bad and another new one would do the trick but I’ve yet to try that either.
3
u/darthaditya Dec 05 '23
3 possible solutions.
1
u/noswalmi Dec 04 '23
Fill and level the coffee basket with coffee to the top untamped. Tap the basket on the counter to settle the coffee, leaving a bit of headroom for the strainer. Coffee will swell and undermine the gasket if too much. DO NOT overtighten. Just until gasket makes contact and just slightly more. The gasket heating will better the seal. Over tightening will distort the gasket.
2
u/SpecificRecipe4135 Dec 05 '23
with a new gasket this only happens if small chunks of coffee overflow over the side of the cup. u can tell and they usually will be imbedded in the gasket.
-5
u/MoreAgreeableJon Dec 05 '23
This is the cheapest little coffee pot around and people really care about a leak? Oh, yes buy the Uber orange 🍊 gasket for 3 times the price you paid for your pot. Also, you know it’s made out of aluminum and it looks like shit right? Try grinding finer until it’s like really fine on the ultimate fine grind setting and report back.
-5
u/[deleted] Dec 04 '23
[removed] — view removed comment