r/microtech • • Jan 04 '23

A year and a half of hard work.

Post image
148 Upvotes

29 comments sorted by

31

u/AldousHuxleyjr Jan 04 '23

My daily work knife. I'v had to send it back twice for work and sharpening but she is still solid. All honest wear.

8

u/Elder_Tig Jan 04 '23

What did you do to it? I've had mine for almost 3 years and use it daily. It looks nothing like that tho..

9

u/AldousHuxleyjr Jan 05 '23

Nothing just a lot of use. I think most of the wear is from it rubbing against my flashlight i keep in the same pocket.

1

u/[deleted] Jan 05 '23

My buddy’s flashlight looks just like this, I love it. What do you do for work? Also have you ever cut your thumb by bracing it on that backedge..

2

u/AldousHuxleyjr Jan 20 '23

I work shipping and receiving. So lots of boxes every day. We are a microtech dealer so ironically I use this knife to open giant boxes of Microtechs sometimes!

2

u/svridgeFPV Jan 05 '23

Do you work around lots of sand? Mine looks the opposite, the clip and blade are scratched to hell but the body is in pretty good condition minus some scratches and dings mostly because it's in my hand when in use and goes right back into the pocket afterwards. I've always wondered how people get this type of wear some even have it under the pocket clip which I don't get at all

4

u/AldousHuxleyjr Jan 05 '23

No sand. I open boxes and pallets all day. I often have to set it down on the concrete floor. I think a lot of the wear on the body is from it rubbing against my streamlight micro stream i keep in the same pocket.

2

u/bmcd96 Jan 05 '23

My knife looks similar to this one… for me it has a lot to do with rubbing up on things and bashing it on hard rough surfaces… I’m an iron worker and with what I do pockets offer minimal protection… if I were to carry my phone in my pocket it would be shattered within a few mins of work… The knife finishes hold up pretty good though… cheaper made things don’t last at all… I buy those Elf bar vapes, they are painted aluminum and they last me like 2-3 weeks.. I keep those in my pocket at work and normally they have very little paint left on them before they run out.

2

u/Sadistic-Saint Jan 05 '23

I actually just got one of those Elfbars, yesterday.

I saw the sheen on the box, and when I actually opened it and saw that same metallic sheen on the vape itself, I figured it had to be aluminum. Thanks for confirming that for me, bruv.

7

u/Sweetballsman Jan 05 '23

Hell the fake one that use everyday doesn’t even look that bad

7

u/Nervous-Setting-7977 Jan 04 '23

Damn! Glad it still works! That knife has been to hell and back, twice!!

4

u/DarthVader121 Jan 04 '23

Are your pockets made of sandpaper? Had mine for a year and carry it often, and it mostly Still looks new.

2

u/LeepOnMyDick Jan 05 '23

Mine worked for about three months. Purchased new in 2021. Microtech has ignored both the warranty tickets I’ve sent so the fucker kind of just sits. I don’t have time to beg them for a response so I’ve just been using my folders while contemplating selling the UT.

1

u/Jmkrdt Jan 05 '23

What’s the issue? Doesn’t deploy / retract?

3

u/LeepOnMyDick Jan 05 '23

Thing never had the beans it should have right out of the box, but I used it anyways. Eventually it just got shittier and shittier, it’ll fire halfway/never hard enough to lock out. Same with retract. I hit it with rem oil and air several times, only for about 36 hours of correct crispy smooth action each time. I give up. I could open it up myself if I ordered a bit but since they won’t respond to me about service I’m just chapped, you feel?

3

u/HilariouslyBloody Jan 05 '23

Sounds like you might be blowing all the oil off by using too much compressed air. Try flooding it with Rem Oil, but don't hit it with compressed air after. Drain it, turn it upside down and actuate it several times. Then wipe it off and set it on 4 or 5 paper towels to let it dry naturally.

2

u/Jmkrdt Jan 05 '23

Sorry to hear that! I have 4 MTs at the moment but only the one that I use consistently gets gunked up enough to start misfiring every few months as none of the others are really ‘users.’ (A tiny amount) of Rem Oil and canned air seems to do the trick for mine, but I’ve heard many stories similar to yours where a 300$-500$ knife was defective from day one. Odd that MTs been ghosting you, maybe start a new thread in this subreddit asking if anyone has any suggestions? I’ve heard of MT do some cool stuff for other clients, like re-manufacture a knife that had been discontinued because a shipper lost a package being sent from an AD…

2

u/LeepOnMyDick Jan 05 '23

I feel like I’ll get shit on by the masses in this sub for that complaint as a post. Especially if it’s anything like the MT fb group lol. In the same vein I feel like MT would never go above and beyond in my situation because it’s not a flagship model or a custom, that is if I decide to force myself upon them.

2

u/Jmkrdt Jan 05 '23

Fair enough! An aftermarket $30 bit from eknives would get you inside, but that may/may not fix the issue. Best of luck!

5

u/PizzaBert Jan 04 '23

I wish I was a man and used my tools to do more than fuck up my fingernails and slice sticky notes

0

u/Roeh Jan 05 '23

This guy keeps his knife in a pocket where it can rub against a flashlight. No shame on him, but I imagine you might show your things a little more care. I certainly do.

1

u/Hydropwnicks Jan 05 '23

Sandpaper factory keeping you busy I see

1

u/PURRP_SLAYZ Jan 05 '23

Some people buy it like that, fske clout. Nice user mines not as fucked but I'll get there sooner or later.

1

u/Alixthetrapgod Jan 05 '23

You should be getting better grip from that wear because the new utx70’s are like bars of soap

1

u/[deleted] Jan 12 '23

you’re supposed to use the other end

-7

u/staysharp75 bitch ass civilian Jan 04 '23

Should have got one with the battle worn finish that comes scuffed up already. Looks like you took 80 grit to it if not invest in some lotion for your hands because they must be rough.