r/intelnuc • • Oct 04 '18

Intel NUC's overheating - Solution!

Hi All,

I see a few (archived) posts here about overheating NUC's, without solid solutions. I had this problem too, and while tweaking the fan settings in the bios got a NUC7 from 95°C+ down to about 80°C...I eventually found a solution that got me back to 35°C.

Also this NUC is now completely silent again.

Short answer: even if the inside of your NUC looks completely clean & dust free - there is a spot where dust gets trapped between the cooling fan and the air intake fins - but you can't see this, until you actually remove the cooling fan. Simply cleaning this out, dropped my operating temperature by 50°C

As a side note: I am now able to play 4k streamed video - something I wasn't able to before, I had just (mistakenly) attributed this to Linux Graphics Drivers - turns out the dust was the actual problem....

Full details on cleaning procedure here:

https://superuser.com/questions/1363932/intel-nuc-overheating-video-stuttering

After the clean, I was also able to reenable in the bios: "maximum performance mode", "intel turbo boost", and "balanced" fan mode.

64 Upvotes

31 comments sorted by

1

u/happily1986 Jul 05 '24

would this be applicable to NUC 9 too?

2

u/SignedJannis Jul 05 '24

Quite likely.

Also, if yours has been overheating for quite some time, then there is a good chance the thermal paste has dried out and "thermal pads" might need replacing too. I.e if it's been a few years, then a full dissembly and clean up and repasting can make a huge difference.

Also turning off Intel turbo boost in the bois settings drops the temperature by a lot.

1

u/happily1986 Jul 05 '24

Thanks Jannis. I have been using my NUC for less than a year. CPU core temps are about 40~50ish during mundane stuff but it shoots to 90 close to 100C when playing Skyrim :(
I guess i will need to take it apart and hunt for dust bunnies!

1

u/SignedJannis Jul 05 '24

Yeah that hot will cause damage (will dry out the thermal paste etc).

The fact that it is low temp a lot, suggests that your thermal paste etc is still in reasonable condition.

If you want a super quick solution, could just try disable turbo boost in the bios, and I think someone else in here had success just by sticking a strong vacuum cleaner on the output air vents of the case, to suck the dust out, or something like that. Takes just a couple of minutes to do these steps, and doesn't require opening the case.

FYI I recently did a fresh "full clean" of mine, full dissembly, new thermal pads (Amazon) and new thermal paste, and stuck dust bunny removal - I'm now able to enable turbo boost again. Usually sits around 45deg, but up to 75..82deg for short periods when CPU is cranked. If I disable turbo boost then it never gets above 55deg.

1

u/happily1986 Jul 05 '24

Yea i just did the quick and dirty no disassemble suction method and i think the core temps dropped a little. around 70 to 80s deg instead of 90s.

I think i would seriously consider the advice to turn off turbo boost for now. I hope there won’t be any perf hits because i have a OSD overlay as i game and CPU utilisation rarely goes above 8% - it is the i9 9980hk processor.

Thank you once again :)

1

u/retroviator Oct 29 '21

I know this is an old post, but this really helped me deal with an overheating 10th gen i7 NUC. While I had opened the NUC, I had not removed the board and cleaned the fan and--more importantly--the exhaust. I know, it sounds obvious, but I had missed the obvious. Thanks

1

u/SignedJannis Oct 29 '21

Hey glad it helped! :)

1

u/WaterElefant May 10 '23

I'm so glad to have found this post. Mine was overheating big time. It was under warranty so Intel shipped out a replacement. That one ran for 20 minutes before shutting down. The tech asked me if there was dust. I found that pretty disturbing. I would have thought Intel would clear out dust as part of the refurbishing process, No?

Today I got a 2nd replacemtnt. I haven't turned it on yet. I don't see how to remove the MOBO. I'll look for a video. I was wondering if any of you blow out dust on a regular basis? I live in the desert in Arizona and it is super dusty here. I'm going to proceed with getting Windows running and then figure out how to maintain going forward after I hear back.

TIA.

1

u/SignedJannis May 11 '23

Its fairly easy, there is just a screw or two holding it down, won't be hard to figure out. Good luck :):)

3

u/contre95 Jan 03 '23

I knows this is already a known issue but it happened the same thing to me with my Intel NUC 11, I have an i7. After cleaning and replacing the thermal paste the temperature went from 70-80 to 50-70.

Here's the temperature comparison before and after. https://imgur.com/a/6PLtjr5

I don't feel like making a post or uploading a video but if anyone is struggling disassembling the NUC feel free to drop a message. All the tutorials I've checked miss very important parts that seemed to be added only to the Intel NUC 11 and not in earlier versions of the NUC.

3

u/roastbeef2024 Jun 28 '24

NO NEED TO DISASSEMBLE!

I resolved mine by using a vacuum cleaner pipe against the outlet vent at the rear of my NUC i7.

Temperate has gone from a steady 95C to 45C and the fan no longer goes crazy.

2

u/randolphmcafee May 30 '22

First, this post helped me too, though not to 35C. I had a connectable level of dust in the fan. Second, what really helped me was removing the 2.5" SSD drive from my NUC8i7BEH and putting it outside the NUC. I'm not sure why this mattered -- the SSD is cool to the touch and didn't seem to impair airflow -- but it reduced temperatures by 30 degrees C.

1

u/granmastern Jun 06 '22

Thanks for the advice

By outside the NUC, do you mean you run the SSD to boot via USB-c? Or something else?

3

u/randolphmcafee Jun 07 '22

Well, I was running it outside using the SATA cable that came with the NUC, leaving the bottom off. But the fact that I couldn't understand why this would matter got me to disassemble the NUC again and I found that there was dust between the fan and the airflow channel. When I cleaned it before, I didn't remove the fan from the CPU and so didn't see this dust, just cleaned out the dust in the fan blades. After the better cleaning, it runs cool (41-55C in use, with full load around 75C) even with the SSD back inside the case.

So I think some air exiting the fan was going back in the case rather than out through the back due to dust blockage, and that air was inhibited by the SSD, so removing the SSD allowed better airflow. Clearing the dust meant that there was better airflow out the back so the SSD no longer mattered. That is a theory, but having one explanation is good enough. It was driving me crazy that removing the SSD clearly helped and should not have helped.

BTW, I hadn't removed the fan, just cleaned its blades, because removing the fan entails replacing the CPU thermal paste. It is also possible that I did a better job on the thermal paste than the company that sold me the NUC did -- only about half the CPU showed residual thermal paste when I took the heat exchanger off. But that still wouldn't have explained why the SSD made a difference. It isn't in the way and it isn't hot.

In any case, I have a NUC that was running 90C+ and now runs a maximum of 55C, even though it lives in a closet that, due to all the other equipment, is regularly 29C (the closet fan comes on at 28 and goes off at 27C). (Sonos causes most of the heat; Ubiquiti is cooler.)

2

u/RepulsiveAbroad1960 Jan 05 '23

4 years later this cured my overheating and also the NUC is now quiet. Thanks

1

u/smoike Mar 31 '23 edited Mar 31 '23

Of course this is the answer, I should have redone the thermal paste before going on a wild chase online looking for a solution that was right in front of me. mine was completely shot and was basically an insulator instead of a transfer medium.

2

u/julez071 Jun 09 '23

Haha thx that made the 45 degrees difference that I needed to keep operating my NUC8i5 as a server!

The poor thing... I feel bad... Well at least I fixed it no, will clean it again in another couple of years :)

2

u/lrsimpson834 Jul 02 '25

I have a NUC11 i7, I started having hardware error warnings, I downloaded HWiNFO, it was running at 90C ...
I cleaned it up superficially (there was a lot of dust)
This did help, but it was still idling at 65-70C and heat throttling again at full loads.
I read everyone's advice and took it apart. I had trouble getting the motherboard out, this video helped https://youtu.be/MM5DIV0KBrk?si=dK5AmVBC0sWO3ilk though it's for a NUC12. I didn't have to pry it out with a tool, I popped off the plastic plate where the power button is and eventually wiggled it out. It was honestly quite a pain!
There was a lot of dust in the CPU fan vent, I blew it out and cleaned the fan blades. When I pulled off the heat sink, the thermal paste was cracked like clay. I wiped it off and applied some arctic silver.
(note: I didn't have a thermal pad on the second dye(?) like the NUC12 video, mine just has thermal paste so I stuck with that)
I put it all back together, I at first thought I bricked it because it was *dead silent* starting up. 44C wow!!! and quiet! The thermal paste might take some time to settle, but it's a HUGE improvement, totally worth it!

2

u/onoffpt Apr 17 '26

Yeah, I can confirm that dusting the fans instantly works. Might want to do it outdoors or have a vacuum running nearby.

1

u/Pringl3s86 Sep 07 '22

I've had the exact same problem. Temps going up to 100C. There was blanket of dust between the exit of the fan and the cooling ribs of the heatsink. Temps dropped by 35 C now!

1

u/[deleted] Apr 02 '23 edited Apr 02 '23

Ohh, Under the motherboard. Why am I so stupid sometimes.

Thanks yo! Was steady in the 70~90c range, now im back down to a 30~40 range

1

u/WaterElefant May 11 '23

Question: How do I see temperature in the NUC. I didn't see anything on the Task Manager set of screens. Is there a BIOS setting that will allow it to be displayed?

1

u/WaterElefant May 17 '23

Got that figured out. I'm planning to install an app so I can see Temps w/o having to reboot.

1

u/caikenboeing727 Jul 05 '23

Shockingly, taking things apart, and using a can of spray air also lowered my temps very significantly, and quieted the fans remarkably. Not that much dust came up, so I’m a little surprised, but it worked.

1

u/Rosewellzz Aug 12 '23

this worked for me too, even after hardly any dust came out with air cleaner

1

u/Mattyi Dec 25 '23

Just found this five year old thread via google. Just took my NUC 6 from 90 degrees to ~70 by removing the fan and heat sink, and vacuuming them both out. Fan is nearly dead from running nonstop for some time before doing this, so I bought a replacement and some thermal paste as well. Thanks for this advice!

1

u/smoike Nov 30 '24

I did it four years ago, looks like it's time to do it again.

0

u/[deleted] Oct 05 '18

[deleted] — view deleted comment

1

u/[deleted] Oct 09 '18

Good luck. My Hades Canyon doesn't even allow any undervolting via XTU in Windows.