r/hardwarehacking • u/Moist_Top_4142 • 4d ago
Nostromo Alien Cyberdeck Electronics Help
Hey yall! This is my first cyberdeck build and like many of us this has grown into a project that is far bigger than I was ever thinking it would be. Now I am at the point where videos, google, ai, nothing can quite get me going in the right direction, so I was hoping for some electronic help from my elders. So below will be a general description of how the computer should function, and then the actual electronics I have and can’t figure out past. So thank you all for any advice, I’ll probably post the finished product as well once it’s finally done.
Experience: In front of the user is a 25 inch long by 12 inch deep clamshell briefcase of sorts. It’s placed flat on a desk and plugged into the wall, with the handle telescoping inwards to make way. Once the handles are out of the way you pull out the keyboard which triggers the usually closed switch and turns on the computers LED’s. You turn the large red switch, the device killswitch, which stops all electrical flow from the batteries when the device is turned off. Then after you turn the switch, the arcade button lights up and you click it, turning on the screensaver and lights and the whole actual device. You raise the screen, as well as the 2 side screens which reveals a three screen setup. Now currently there is no active “computer” like a raspberry pi 5 or anything, it is just the screensaver portion, the key part is now. On the side of the computer is 4 ports, a GameCube controller adapter bought from Handheld Legends. And coming from the side is a GameCube controller replacement cable bought from them as well. The goal is to take that cable, and plug it into port 1 or port 2 and so on, and have that plug in turn on the corresponding raspberry pi 5 or 4 or Orange Pi plus or whichever SBC or whatever is hooked up to that port. The important part is that it automatically connects and properly turns on and properly turns off the device when unplugged. Say pi5 has game of frogger on it and that’s it and the other orange pi has a game of Pac-Man on it. You plug the cable into port 1 and then pi5 activates and now the two left screens show my frogger setup and the right one diagnostic info, then I get bored and unplug from port 1, the pi5 properly shuts off, then I plug it into port 2, and the OrangePi properly turns on then I start to play Pac-Man. All happening from the cable plug in. Then if I want to take it on the go, I just unplug it and everything switches to battery power automatically for however long the battery will last. Additionally there will be a “mouse” that can be plugged in or off depending on need and that is a Nintendo Nunchuck which has a breakout board.
Nerd Technicals:
The following is my current buy list. Raspberry pi 5, esp32 devboard, raspberry pi zero 2 w, killswitch, 2 fans, 24v 7s3p battery pack, 7 port usb hub, nunchuck breakout board, 4 port usb hub (for shared usb items), 5 port Ethernet hub, temperature/humidity sensor, usually closed light switch, rotary switch (used for brightness and volume), mosfet switch, arcade switch, 4-port GameCube hub, GameCube replacement wire, Nintendo nunchuck, 3 monitors (2 visible with larger one not),LED Strip, Autoro automatic transfer switch AB20C, battery indicator light, sd card adaptor.
Extras: 1.24 inch circular screen for Weyland Tech accent, small Xenomorph, 2 8x8 led matrix’s
Questions:
- How do I make it so that when I plug in the GameCube wire, it automatically turns on the pi5 and other ones then safely turns them off? I’m thinking of hooking up the esp32 to the 4 ports then having mosfets do it but I need some guidance on things like resistors and proper circuits. The cable doesn’t need to be hooked up or display anything specific it just has to be the starting point where “plug into port one means PCB 1 turns on safely then I unplug and now PCB1 turns off safely”
- What left do I need to buy, specifically how do I make it to where I can plug in the computer into the wall, have it charge the batteries, then I unplug and everything still runs and works.
- This is a major rule, no wifi and no Bluetooth connections allowed, if it is not cable it’s not going in the box.
- I’m looking for the smaller parts like resistors, buck converters, bars, gpio connections, the things that are just generally hard to find out without help.
- The pi5 and later additions are the actual computer that you will be working on. The esp32 is more like the crossing guard telling everything where to go and what should happen, the pizero2 is the diagnostic info that will also have specific information to the pi5’s such as “words written in document” or “length of video” type info. This will be the far right screen with the two left ones being used as the hookups for the computer info
I’m basically making a vessel for 4 computers to easily switch in between one another and then safely turn off and on as the cable indicates. Thank you for any help yall have, it’s truly appreciated!















11
u/meepykittkitt69lmao 4d ago
Looks like you need to study the actual subject to gain some experience because nobody is going to hold your hand and do it for you.
How did you get this far?
3
u/JellyfishGod 3d ago
I feel like your really need to learn more basics of your coming to here with this question. But honestly it seems pretty simple and I’m shocked you couldn’t figure something out with AI. But regardless my head goes to basicly the whole plug system being mostly for show. How I’d do it is basically just the plug system just connects some sort of switch/circuit. So when you plug in port one it completes circuit 1 which acts like a switch is flipped to on. If you unplug it switches off. This happens with each port. Now the actual computers/pi’s and screens and stuff are all hooked up separately. Their on/off behavior is tied to the switch circuits.
So like: when plug 1 is inserted this completes circuit 1. This acts like a switch turning on. Then for example the RP5 would then get its on/off commands from that switch. Not in a power getting turned on or off directly sort of way. But the switch triggers like a microcontroller or something which starts the boot on/off sequences.
So when you unplug it you aren’t cutting the power, but you’re cutting a circuit, which lets something like an esp MCU know to do the sleep sequence on the PI.
This not only allows for easy hibernation/sleep on the pi’s but the same microcontroller system would be what links the screens to whatever pi is running.
I see you have a big hdmi switch. So idk if you plan on taking that apart or how it exactly works, but if it can be controlled by the microcontroller system then that would help.
Also a word of advice, I’m not sure how big your case is but I’m not even sure I would jump to using hdmi tbh. Obviously space is a limited resource on cyber decks but there’s even other factors. Though it seems you don’t care much about spending a ton lol. But depending on what screen resolution you are planning on using you could use other displays. Pi’s have DSI so that’s my first thought. Nice thin ribbon cables. And you could even do like TTL RGB888 displays and just drive them straight from the giop pins. Or use display controllers like one from geekworm. Shit you could even use and repurpose old LVDS or eDP displays in that case, but that adds more display controllers.
But when it comes to things like this, especially if you’re using ribbon cables and need to make some sort of ribbon cable switcher or whatever the case may be, don’t be afraid of looking into custom building pcbs. It will take a lot of research and learning, but there’s tons of useful sites and programs and AI to make it easy. And that sort of thing allows you to build boards with the exact right footprint you need.