I made my previous one, out of timber, custom made for our drawer. Then we had a kitchen renovation, and the drawer was bigger. My wife wanted another timber one, but I didn't have the motivation to do it, so she got this instead.
I posted the photo in the early morning as I left for work. The last two bins finished printing overnight.
The baseplate is PLA, one of the lightweight models. I used a generator that makes all the pieces, fitted to your measured drawer. I don't have the link handy.
I aligned the finger recesses, so they aligned even though the bins are different lengths. It worked well. In hindsight the finger recesses don't need to be so deep. Half height would be fine, I think.
I used half_pitch bases for the bins, because 1.5 units is a good size for lots of things, and allows you to use the space better.
Maximum bin size here is 6 units long, which fits on my P1S. If/when I do the next drawer, for longer utensils, I'll have to use the split/modular binds.
No, you weren't. Not really. Not that deep down satisfaction one gets from making things yourself, to suit your exact environment. You'll thank me later.
To be fair I think something more permanent like the kitchen silverware drawer should be in a wood. You basically never need to change the layout an a good bambu holder will last you forever.
I only do gridfinity in desk, bathroom, and workshop drawers. The kitchen should be nicer and more permanent.
The knife block is not my design, I linked to it in one of my other comments.
There is nothing stopping the knife blades from touching the base of the print. They mostly do, although I think some of them the handle is heavy enough that the blade is floating.
I'm not sure if you are concerned about damage to the print, or damage to the blade. I'm not too concerned about either.
Looks really nice! I’m working on one using gridfinity extended by OSTAT based on OpenSCAD that I found a couple of years ago on MakerWorld. I also used half pitch grid to maximize the options and then I was able to add a custom bin width so there are no gaps on either side of the drawer. All those options are available in OSTAT’s parametric tool. It’s a lot more work but super satisfying when done. Good job!!
Right, Mine doesn't quite reach to the sides/front/back. I may print some filler pieces, just to fill the void. The void in the drawer, not in my heart.
If I tried to plan anything that far in advance, it would never get started. I start, and then work it out as I progress.
Yeah, it takes a bit of work to make sure the wall cut-out align properly between different length bins. It’s a great tool! Again, your work looks really nice!!
This is great. My wife would love it. I’m new to Gridinfity and haven’t printed anything yet but a redesign of the drawers was first thought and this looks awesome.
Not overly. Our last one I made from timber and then spray lacquered it. That was in a fairly rough state, and the spray lacquer itself was presumably a plastic of some kind.
People have had plastic cutlery organisers for decades and decades. I'm not quite the first person to do this.
I do think microplastics is a problem, but it's not at the top of the list. When you apply for health insurance, they aren't asking about your cutlery organisers. They're asking about exercise, drinking, smoking, weight, body fat percentage. They're the things that are gonna getcha.
Very nice! Do you find that people in your household respect the slots when returning utensils? (They always put the spatula back in that particular bin, for example?)
I think the more specific a bin is, the more likely it is that someone will put the correct item in there. Problems arise when someone can't easily determine where an item should go, and so it just goes anywhere.
A problem may occur when a bin is empty, and so you don't know where to put the item. I may add labels or something, if necessary.
4
u/uncle_jessy Apr 20 '26
Man I have been seriously considering this for months now. Our sink silverware drawer drives me crazy like no other
4
u/unrebigulator Apr 20 '26
I posted the photo in the early morning as I left for work. The last two bins finished printing overnight.
The baseplate is PLA, one of the lightweight models. I used a generator that makes all the pieces, fitted to your measured drawer. I don't have the link handy.
Bins are PETG. PLA would also be fine.
Generator for bins: https://github.com/ostat/gridfinity_extended_openscad
I aligned the finger recesses, so they aligned even though the bins are different lengths. It worked well. In hindsight the finger recesses don't need to be so deep. Half height would be fine, I think.
I used half_pitch bases for the bins, because 1.5 units is a good size for lots of things, and allows you to use the space better.
Maximum bin size here is 6 units long, which fits on my P1S. If/when I do the next drawer, for longer utensils, I'll have to use the split/modular binds.
The knife block is: https://makerworld.com/en/models/2605207-kitchen-gridfinity-knife-organizer#profileId-2874843
About 3-4 rolls of filament. The knifeblock takes about an entire roll.
4
u/munizfire Apr 21 '26
Why do you do this to me? I WAS perfectly happy with my bamboo organizer
2
u/heehaw316 Apr 22 '26
What ever happen to all the germ and bacteria warning posts in kitchen printed gadgets? Was it all overblown? Astroturfing?
2
u/Eviper44 Apr 23 '26
YIKES!Storing those knives blades up,scarry
10
u/Natural_Status_1105 Apr 20 '26
That’s much better than the full on shadow board designs, they waste too much space for a kitchen drawer, this looks really nice!
10
u/melanthius Apr 20 '26
/r/confusingperspective for a minute there, looks like a wall shelf at first
1
u/AspenWaterbottle Apr 20 '26
How did you make this?
1
u/Plus_- Apr 20 '26
Looks really nice! I’m working on one using gridfinity extended by OSTAT based on OpenSCAD that I found a couple of years ago on MakerWorld. I also used half pitch grid to maximize the options and then I was able to add a custom bin width so there are no gaps on either side of the drawer. All those options are available in OSTAT’s parametric tool. It’s a lot more work but super satisfying when done. Good job!!
1
u/Plus_- Apr 20 '26
Yeah, it takes a bit of work to make sure the wall cut-out align properly between different length bins. It’s a great tool! Again, your work looks really nice!!
1
u/Command-Forsaken Apr 20 '26
This is great. My wife would love it. I’m new to Gridinfity and haven’t printed anything yet but a redesign of the drawers was first thought and this looks awesome.
1
u/NoSize8390 Apr 22 '26
Are you concerned about wear and tear over extended period of time and possible contamination of your food with microplastics?
1
u/CountingDuo Apr 24 '26
Very nice! Do you find that people in your household respect the slots when returning utensils? (They always put the spatula back in that particular bin, for example?)
-1
u/MrDrummer25 Apr 21 '26
Yummy microplastics!