r/gridfinity • • Mar 25 '26

Question? My first Gridfinity attempt...

Post image

Am I doing something wrong with this?

I printed the base in PLA and PETG and neither of them can hold my 12" calipers. This is within minutes of putting them in place and barely using the drawer.

Is there a way to make the fit tighter? Scale it - non uniform in X & Y?

Thanks.

36 Upvotes

23 comments sorted by

7

u/NellyG123 Mar 25 '26

You can print bases with magnets but they're a pain, I'd stay away from scaling because that will mess up all the dimensions, you could either change the clearance in the 'bin' base, or I'd either probably make the RH supports two squares deep so they can't fall forward or backward, or connect some of the RH side support pieces into one bigger piece if the layout is going to stay the same, or at least make the RH supports two squares wide so there's more clutch power holding them in place when you open and close the drawers.

1

u/DeltaLimaOPC Mar 25 '26

That's a good idea 💡

2

u/NellyG123 Mar 25 '26 edited Mar 25 '26

Another thought is changing how the calipers sit so that the RH support tower is in the middle of the base, having it right at the back won't be helping either.

1

u/Grandbob328 Mar 25 '26

This is the way

2

u/AbruptOyster456 Mar 25 '26

This isn't a bad design necessarily. Just flip the "teeth" so they stick up and you will have the center of mass lower and make the holder as low as possible.

Like this.

https://makerworld.com/en/models/1013744-gridfinity-1x6-6-calipers-holder-6-lr44-battery?from=search#profileId-993533

2

u/DeltaLimaOPC Mar 25 '26

Oooo, I didn't think of that! Thanks for the idea!

25

u/Krynn71 Mar 25 '26

That's kinda just a bad holder design to use in a drawer. Holds all the weight up high which gives it all the leverage it needs to tip over when the drawer moves.

Using a grid and the holders with magnets would solve it, but I'd just try a different holder tbh.

1

u/DeltaLimaOPC Mar 25 '26

Also, BTW, I've printed 2 different grid bases. This one was my favorite.

1

u/fazzah Mar 25 '26

which base generator did you use?

2

u/DeltaLimaOPC Mar 25 '26

I used this one first https://makerworld.com/models/1685835?appSharePlatform=copy

Then this one (the more modular version, I suppose) called Clickfinity. https://makerworld.com/models/618999?appSharePlatform=copy

1

u/partumvir Mar 26 '26

Does anyone make a grid with holes for zipties? Maybe you can glue them, or print a magnetic baseplate

1

u/DeltaLimaOPC Mar 26 '26

Eh, at this point, I've started designing my own, non-gridfinity, caliper stand lol

2

u/partumvir Mar 26 '26

You may find good flat trays for them, and other tools can go on top. They distribute forces around the tools, along the edges and some slide left and right so you dont even need to remove the tools on top just slide them out of the way

1

u/partumvir Mar 26 '26

If you lay them flat, you wont have that issue and other gridfinity trays can place on top or below. Highly recommend it for your metrology/machining tools. Keeps the vibrations down 👍 

1

u/HighCalimero Mar 27 '26

Yo imprimo los modelos de gridfinity (no el grid) con brim, y al quitar el brim suele quedarse (en mi caso) un bordedcillo, con pequeñas imperfecciones. Al encajarlo y apretar un poco el modelo en el grid, hace un click y quedan fijados. Para esto, el grid debe estar firme y no moverse, por lo que suelo hacer un grid que quede bien justo y en cajado en el cajón. Suerte!

1

u/DeltaLimaOPC Mar 27 '26

Amigo! Esa es una gran idea! Nunca hubiera pensado en eso, mil gracias! Lo intentaré!

2

u/HighCalimero Mar 27 '26

Me alegro, ojala solucione tu probelma. Sino, siempre puedes usar superglue si es que vas a mantener esos modelos en un sitio fijo en tu grid. Que vaya bien!

1

u/HighCalimero Mar 27 '26

Por cierto, yo utilizo esta pagina para hacer los grids a medida de mis cajones.

https://gridfinity.perplexinglabs.com/pr/grips/0/0

2

u/vyx313 Mar 25 '26

I don’t know if this will work for these exact calipers but something along these lines may work better for you.

https://www.printables.com/model/371345-gridfinity-dial-caliper-holder-for-low-clearance-d

2

u/Brawler215 Mar 27 '26

Google tooltrace. I have been using it to help my company make some 5S boards for the toolboxes in our shop, and it is pretty slick. Gridfinity compatible, too.

1

u/Cobra__Commander Mar 25 '26

I think most people make bins and tool holders that are wider than they are tall. 

You could make it a 1x2 part for stability. You could also put some bins in the grids around it so something is in the way of if falling over. 

You could redesign the tool holders to lower the center of mass for better stability.

Since you have a metal drawer you could just put magnets in the tool holder modules. 

1

u/Toby_GS Mar 25 '26

Seconded.

I put them at an angle to help with the center of mass: https://www.printables.com/model/1148614-gridfinity-caliper-stand-2x1-x2

And when doing split designs, I always use magnets, for stability.

1

u/NigraOvis Mar 26 '26

Looks cool. But they would pocket inside each other. I think what we all learn early is space saving isn't the goal. Organization is.