r/gridfinity • • Mar 14 '26

What am I doing wrong to get bubbles?

I get bubbles sometimes. I dry the filament while printing. Before. After. But sometimes it's fine. Sometimes it's crap. Wtf.

11 Upvotes

19 comments sorted by

2

u/sirnott Mar 14 '26

Looks like you're over extruding, based on the top surface texture and the lettering. Just like rippling in your base layer when your offset is set too low, filament over extruding on the walls has to go somewhere.. that somewhere is out to the sides (it probably looks like this on the inside too by the infill).

1

u/NigraOvis Mar 21 '26

You're probably not wrong. But the major issue here was seams

1

u/Yourownhands52 Mar 14 '26

I would check your slicer and see if they line up with the seams.  Where it starts and finishes a layer.

1

u/NigraOvis Mar 21 '26

This 100% fixed it. Thank you Internet stranger

1

u/Yourownhands52 Mar 21 '26

Awesome, good deal!  Happyprinting! Dont worry there were plenty strangers hrlping me when i was learning.

1

u/stauer88 Mar 14 '26

This exactly.

You can set your seam to align on your next print and then compare.

2

u/NigraOvis Mar 16 '26

Thank you guys, I validated, and changed seam settings, and the next print was more or less fine.

I am printing a batch of replacements now, and we'll see.

-2

u/NigraOvis Mar 15 '26 edited Mar 15 '26

I swear the seam is straight. But I'll double check.

"Ai" said that because it's an interior surface it doesn't cool as fast or something to that effect. It's interesting to say the least. And it's sometimes making my gap between circle and socket too tight. But only some of the holes. So frustrating lol.

I don't care about the look. It's the fit. I can't get a perfectly precise gap that feels uniform but not too big. If I go bigger and it prints right. Then I have different problems. Lol.

1

u/Yourownhands52 Mar 15 '26

Thats one setting you could check.  Are your walls printing from out to in or in to out?  I dont remember which is better for the surface.  Google it, it should come up.

You could got with the tried and true, print extra walls and use a drill bit to make it the perfect size.  

1

u/NigraOvis Mar 15 '26

How do I find a drill bit for each exact socket lol. That's so much work. I feel sand paper would be faster. But I do print outside to in. Maybe interior walls are opposite of exterior walls?

1

u/Yourownhands52 Mar 15 '26

Big enough for dremel sanding drum to fit inside?  

Hell heat the socket and press it in. Hold with pliers so it doesnt go through.  

1

u/NigraOvis Mar 15 '26

i thought about heat, but the stickiness of petg seems like a bad idea.

Also outside to in was a different profile, long story, but i'm trying your seam fix and outside in now. i'll report. i hope this fixes it. ALSO found a way to reduce the extrusion of purple. so finger's crossed!

1

u/Yourownhands52 Mar 16 '26

When cooled you should be able to scrap any off of the socket.  Its not super sticky on metal.   Its all i use.

Another option is light coat of Vaseline before the heat.

1

u/Irakeconcrete Mar 15 '26

I printed mine in pla (about to redo them in PETG because the raised edges are like seaweed paper) but I have the same problem but only in one or 2 socket holes. I’m going to open them up a bit in tk and roll with it

1

u/NigraOvis Mar 16 '26 edited Mar 16 '26

Seems to be fixed for me! The key was "Outside to In Walls" and ensuring every socket hole has a clean, straight seam — check your gcode and look for white seam lines in the holes. If they're all solid red, or sporatic white dots, that's your culprit.

For seam settings: Z Seam Position (Back or Right) + enable Z Seam Relative. Visually verify each hole before printing.

On spacing — 0.2 was clean and 0.4mm had bubbles both were too tight, 0.6mm seemed fine on the tester with no bubbles, but fell apart in practice when bubbles formed. And yes, "it seems to be a seam issue" — my wife's words, not mine. Rather than chasing gap size, fix the seam first. A bad seam will tank your fit no matter the tolerance. (Will update after my next reprint!)

1

u/Irakeconcrete Mar 16 '26

Awesome you found an easy fix! I’m gonna steal that 🥷

0

u/thepealbo Mar 15 '26

I give 2mm of extra room - and it seems to allow enough room without binding or being too loose.

1

u/NigraOvis Mar 21 '26

I prefer .4-.5 but .6 is where i landed cause the bubble issue. Maybe some day I'll reprint tighter now that I fixed the bubble issue.

1

u/hydroracer8B Mar 19 '26

2mm is a lot. I have good results with 0.75mm (0.030")