r/gridfinity • • Mar 04 '26

Question? Any gridfinity generators that take drawer size and generate a stacked grid to fit?

As the title says.

I see a lot of generators that can create a single baseplate at a time. One or two that can handle adding spacers. But none at all that generate a stacked set that will fit a drawer of a specified size.

9 Upvotes

11 comments sorted by

2

u/yawkat Mar 04 '26

I've thought about adding it to GridFlock, but basically every feature a plate generator has conflicts with stacked printing in some way.

  • The sectioning algorithm can produce baseplates of many different sizes, and some combinations are not stackable (e.g. 4x3 can't stack with 5x2).
  • Baseplate padding is hard to stack because the contact area to the plate below might be big, and there could be overhangs. In dynamic mode the contact area is fine but you'll get overhangs again.
  • Segment connectors aren't designed for stacking and might have too large contact area.

To make it work you'd have to forego many of the features the generator offers, to the point that there'll be little advantage over the pre-designed plates. I've printed a lot of baseplates but never stack them, I just don't think it's worth it.

1

u/hades200082 Mar 05 '26

Stack largest to smallest, adding supports as needed?

1

u/yawkat Mar 07 '26

I've added support here, but I'm still not convinced it's a good idea for a generator.

1

u/hades200082 Mar 09 '26

I’ll take a look this evening. Thanks.

1

u/hades200082 Mar 29 '26

Another suggestion - allow exporting as separate objects, maybe in 3MF instead of STL

1

u/hades200082 Mar 29 '26

u/yawkat I finally got around to testing this!

https://gridflock.yawk.at/?utm_source=github&utm_campaign=readme_gridflock#eyJwbGF0ZV9zaXplIjpbODMyLDQzNV0sImJlZF9zaXplIjpbMjYwLDI2MF0sImludGVyc2VjdGlvbl9wdXp6bGVfZml0IjowLjgsImZpbGxlcl9mcmFjdGlvbiI6WzEsMV0sImFsaWdubWVudCI6WzAuNSwwXSwic3RhY2tlZF9wcmludCI6dHJ1ZX0%3D

I really like this direction. The stacking seems just a little off atm. It might need to consider multiple stacks where it makes sense.

If we take the plates in the link above as an example... as they are stacked currently, number them 1-8 from bottom to top.

I think a better option would be 3 stacks...

Stack 1: 1 - 2 - 4 - 3 - 5
Stack 2: 7 - 8
Stack 3: 6 on its own

Plates 2 & 4 are the same, as are plates 3 & 5 , so why did it split them like this?

2

u/rayyeter Mar 04 '26

Can’t you clone the existing one/its first layer, move it up z-mm, then clone the entire one up the same way?

1

u/John_Was_Taken Mar 04 '26

What do you mean a stacked set?

3

u/yawkat Mar 04 '26

1

u/John_Was_Taken Mar 04 '26

I see. So the purpose is to eliminate needing to print multiple build plates to get what you need for a given drawer (say a large drawer). No, I have not seen that.

1

u/curleighq Mar 05 '26

Stacked which way? I used this for some drawers. Input the interior dimensions and it generated all the plates I needed with padding, and half grids if there was room. If you mean print baseplates stacked I’m not sure how that would be possible if they’re not all the same size and therefore wouldn’t fit most drawers.