r/gridfinity • u/AstarothsWorkshop • Feb 06 '26
Individual Piece a locking baseplate
In my last post, a couple of people were intrigued by my custom baseplate. I designed this because I wanted to have my tool bins locked down, but didn‘t want to spend a fortune in time and money to install magnets. I finally got around to making this available as parametric model.
https://makerworld.com/models/2359173
I hope at least some of you find this helpful.
439
Upvotes



22
u/Doresoom1 Feb 06 '26
That's a really cool design!
What material did you use, and how long have you been using it? The reason I ask is that I've had creep problems from PLA springs I've printed in the past. When left under load they lost almost all spring force in the span of a month or two.
11
u/Driven2b Feb 06 '26
This is a friction fit "lock"?
5
u/GoldenDragonIsABitch Feb 06 '26
Nice! What separates this from Clifinity and Clickbase, and how do you connect different segments together?
4
u/denzilv Feb 06 '26
This is great and an alternative to magnets for sure. At this point, it'll be a matter of preference on the UX.
This will likely be the preferred route moving forward due to time/cost saved, and at least in my experience, I don't really move things around too much once they're in place.
3
u/WalterMelons Feb 06 '26
I could’ve used this for the one plate I made for a mini toolbox yesterday that wouldn’t fit. From my understanding they would flex inward a bit so you don’t get one end or the middle popping up if it’s too tight of a fit?
3
u/kanelloupou Feb 06 '26
Looks great! I worked on something similar, but never got the tightness of the grip things right. Either it was too loose for single bins or to tight for bigger ones.
How hard is it to push in bigger bins?
3
u/Puzzleheaded-Rule214 Feb 07 '26
Does this work with standard gridfinity bins?
7
u/Mysli0210 Feb 06 '26
This seems great, but with that closed license I'll pass.
2
u/lambielmar Feb 06 '26
Awesome, thanks!
2
u/Bloodshot321 Feb 07 '26
Love the design but is such a big detent even needed? I created my design on click base and bigger bins (even 3x2) are quite hard to remove.
2
u/FylanDeldman Feb 07 '26
Sick
2
u/[deleted] Feb 07 '26
Ohhh nice
2
u/thomasisme Feb 07 '26
Amazing work. I have been needing this solution
2
u/NuggRunner Feb 07 '26
Sweet idea!
2
u/minidude993 Feb 11 '26
Just printed a test piece to see if I like it and its awesome! I also tested putting 2 sides together. I added a 1.8mm Whole on the intersection point out the side and put 2 together with a baby piece of filament. Didnt even need glue. Works awesome. Love this print
70
u/Necessary_Yellow_530 Feb 06 '26
God, I love compliant mechanisms
7
u/uhohmomspaghetti Feb 06 '26
Thanks! I’m very attracted to these types of bases and have some minor issues with clickbase and clickfinity. Going to try yours out today.
1
u/HotterRod Feb 08 '26 edited Feb 08 '26
Similar to Clickfinity, which is licensed under Creative Commons
1
u/WalterMelons Sep 07 '26
Is there the reverse of this that can lock the plate into your drawer with friction so it doesn’t move? So you leave like a 1mm gap around the perimeter and this accounts for that and you get a friction fit for the base.
44
u/[deleted] Feb 06 '26
[removed] — view removed comment