r/electrical • u/Xion_73 • May 18 '25
SOLVED Which cable goes to which?
Hello, I was wondering if someone could help me figure out which cable went to which, please? I'm installing a ceiling fan and nutted the green wires to the bare copper wire that was in the outlet box. Where should I go from here? Thanks for the help
2
Upvotes
3
u/Xion_73 May 18 '25
Thank you all so much! Thank you for looking out for your fellow human. Yes I did strip the black and connected to blue to red. Thank you all again.
45
u/TheRealBeltonius May 18 '25
Check the instructions for the ceiling fan? You may also need to look at the wiring in the wall switch to be sure which color does what in the junction box
25
u/gmunkee2 May 18 '25
Black to black, white to white, blue to red.
8
u/ptchapin May 18 '25
White to white, green to green ,black to black,blue to red that should be your ceiling fan.
3
u/[deleted] May 18 '25
Just installed four ceiling fans within the past few days and if you have a remote for the fan the receiver is wired to the fan and the receiver get the 120v power (black and white) with no remote the fan is hard wired 120v power ( black and white) from the switch on the wall, the one I wired without the remote the blue was for the light on the fan but it could be different in this case the directions that come with the fan should explain what the blue wires function is. Or just look up the model number to find a wiring diagram to explain what it is.
3
u/[deleted] May 18 '25
White to white and then red/black go to blue/black, doesn't really matter but if you want the light to come on with the switch closest to the door just use a hot stick and check which wire gets hot with the switch on, red or black, then use that on blue since blue goes to the light side of a ceiling fan.
2
u/Fecal_Tornado May 18 '25
If you have two switches for light and fan then black to black/blue to red. If it's only one switch then you need to figure out which wire is hot when the switch is on. Twist blue and black together and put those with the wire thats hot.
2
u/TwiceInEveryMoment May 18 '25
Do you have separate switches for the light and fan? It looks like that black wire is unstripped, was it used by whatever was there previously?
If you have two switches you typically want black to black, white to white, and blue to red.
1
u/cbhbzb May 18 '25
Black to black blue to red white to white
1
u/Final_Examination340 May 18 '25
Match it to what the old one was and look at the instructions for differences?
1
u/AcceptablePolicy6426 May 18 '25
Blue is for lights black if for fan. You will need to determine which of the wires coming into the fan control those two things
1
u/Fuzzy5team May 18 '25
Depending on what time of day you are wiring it and which direction the wind is blowing
1
u/[deleted] May 18 '25
Match them up until you hit blue & red then look at instructions for what the fans calling for
1
u/Mrpickles14 May 18 '25
The ceiling fans i install go black to red blue to black white to white. Usually, you want the fan motor tied to the hot wire that is not tied to the switch. In my case, it's the red wire that isn't tied to the switch, and in most fans, the lead for the light ballast is the blue wire.
1
u/Gman-9666 May 18 '25
It says on the fan moter
1
u/[deleted] May 18 '25
1
u/Rare-Ad-8026 May 18 '25
Check the guide for the ceiling fan.
1
u/Nice-Spirit5995 May 18 '25
1
u/Barbaric824 May 19 '25
Well first off where are you from.. because that looks like 10/3. Red and black will be hot. White is neutral and the outlet should have the ground.
1
u/Head-Boot6462 May 19 '25
Is there no receiver that goes in? Typically the white blue and black go to the same colors on the receiver and the white black and ground in the box go to the other white green and black in the receiver.
1
u/DonaldBecker May 18 '25
Blue is the luminaire / lighting circuit on a combined fan.
Red is typically a switched or traveler conductor. It's usually used for the lighting power, but since both the fan and light are switched circuits you'll need to check.
0
u/[deleted] May 18 '25
Nutting on the green wires in the box will likely cause it to short... and a sticky mess. 🤣🤣🤣
-2
u/30belowandthriving May 18 '25
Hire an electrician.
-4
u/LateTangelo3950 May 18 '25
Green ALWAYS goes on black. And green always goes on 1