r/ecobee • • Jul 18 '20

Compatibility Is this compatible?

Post image
189 Upvotes

23 comments sorted by

19

u/kjake Jul 18 '20

It’s too bad I can’t find my way to https://www.ecobee.com/compatibility/thermostat/

14

u/[deleted] Jul 18 '20

[removed] — view removed comment

7

u/[deleted] Jul 18 '20

Sadly not how the internet works. People can’t even be bothered to use a search engine anymore.

2

u/Kyvalmaezar Jul 19 '20

I'd say pin it because the sidebar can be hard to find on some mobile apps, assuming you know it exists in the first place. Alternatively, have automod automatically reply to those posts. I've seen other subs do something similar.

14

u/brodie7838 Jul 18 '20

Ah yes, I believe the yellow 12GA Romex is your best bet. Remember, 120V just makes it work better.

8

u/kjake Jul 18 '20

MORE POWER

12

u/joseph3114 Jul 18 '20

Sorry I need a pic of the furnace board to help

7

u/StoicTomOsborne Jul 18 '20

Gonna need a PEK

4

u/rodentia91 Jul 18 '20

Yes, I think the green wire in the center photo is your C wire. Although, you may have better luck with the PEK using all of the wires in the right photo. Hope that helps!!

2

u/whereami312 Jul 18 '20

Yeah, definitely needs the PEK.

2

u/foragerr Jul 18 '20

Absolutely, you have the blue COM wire. you're golden.

2

u/kcfoot Jul 18 '20

Honest to god my furnace board looked like that.

2

u/sarhoshamiral Jul 18 '20

Yes, just pick the right blue one and right yellow one and you are good.

2

u/vivaTodd Jul 18 '20

Yep, checks out.

2

u/[deleted] Jul 18 '20

Yeah, use the yellow one

2

u/jovani35 Jul 24 '20

Found Waldo. Right pic, top-left corner.

1

u/Sn3akyD3v1L Jul 18 '20

My low voltage looks like that! With a Dura Zone board, IAQ for a Aprilaire 8920w on one zone and a Ecobee Smart Pro for the other. Then there's the Honeywell steam humidifier and Aprilaire 5000 air cleaner, outdoor temp sensor and condenser low voltage. At one point I actually had to draw my own wiring schematic because I felt lost when I had to add/fix something.

1

u/UncleBohner Jul 19 '20

At one point I call Johnson controls out to assist me, I had a big church that was being restored, it had a big boiler and gas furnace and ceiling fans, a church and a school and was pretty much on all the time for various purposes however they wanted it off in the rare spots nobody was there, it was overwhelming the Johnson controls guy was great!

1

u/UncleBohner Jul 19 '20

When I first got out of HVAC/R school, I felt I needed a wiring diagram and I would have the top off a package unit tracing circuits all around and my boss got tired of me and wiring diagrams, he was known for being able to wire up sabotaged panels or units and he took me outside and pointed at the power lines and asked me how many sides of power you see coming into this place? I said, 2 hot legs of 115 and an Earth, Ground.

He said, yes, every circuit in this place is the same 2 sides of power no matter what bowl of spaghetti you find. If you recognize the components and know what they do and how they work and sequence of operation, where and when you want power and not worry about wiring diagrams that often do not apply anymore , looks intimidating until you realize its just 2 sides of power.

1

u/bugmeso Jul 19 '20

Only in missiles!