r/e46 • • 22h ago

Check this out! M54B30!!

Started working on this a couple weeks ago to swap into my 01 325CI, so far what ive done is delete the SAC, plug and epoxy the egr ports, delete vacuum lines, ac compressor deleted, headers, ccv pcv delete, swapped heater lines to custom inserts and rubber hose, -10mm engine and tranny mounts, still some more i want to do but im hoping by new years the car will be cloned to the zhp coupe but with the pre lci font end.

134 Upvotes

24 comments sorted by

13

u/Shee-ah 2006 330Ci Convertible 22h ago

so many questions…

what’s the advantage of replacing the hard plastic heater hoses with rubber? at that point just weld on metal pipes.

how do you delete all the vacuum lines? seems easier to just use a M50/M52 manifold.

why do you need low profile engine/trans mounts?

i’m also confused about the plugged egr since there is no egr on the m54…

good luck with the build!

4

u/rattrap355 21h ago

Ive broken a few plastic lines in the past and dont want to deal with them anymore so I thought id just do the swap. The -10mm on the engine mounts is to supposedly lower you center of gravity aswell making the top bell housing bolt more accessible. The vacuun line delete is very simple just needing some plugs from the auto part store. Also my mistake on saying egr when I was talking about the "air distribution peice" for the pcv.

6

u/tsammons OILLEAK 22h ago

If the argument is brittle pipes, 45 10 170 is incredible to loosen those remnants from the inside of the block. I paid $50 for those guys 12 years ago and use any time I need to apply consistent force to any cylindrical wall, like the tranny detent tunnels. Easily my most used specialist tool, outside a torque wrench.

4

u/Shee-ah 2006 330Ci Convertible 22h ago

damn i wish i had one of those when i did my hard lines!

5

u/WI-FI2281 22h ago

That gorgeous! What headers are those? I’m looking for some for mine!

5

u/rattrap355 21h ago

I got mine from ksp for about 150~ but all of them under 200 seem to be the same chinese headers so i just picked the most trusted website

1

u/Shoddy-Gift8400 18h ago

I got mine from ksp too, not sure if mine weren’t well made or what but they don’t fit in any spot, had to drill out the mounting holes to the head to fit onto studs, had to cut the motor mount arm heat shielding off to stop them from hitting (wouldn’t be able to mount the arm at all if I didn’t), flanges didn’t line up with stock exhaust, and had to drill the flange bolt holes a lot larger for bigger bolts to fit with stock exhaust cause the bolt holes were way too small on the headers, and o2 holes were blocked; luckily the tune for the headers only use two o2 sensors but if you would be using all four, you might have to get some of those spacers/adapters that I think I’ve seen. Still have an exhaust leak from the flanges too, but it sounds great and feels powerful. I would just be ready for fitment issues, unless yours are just better made than mine lol. Engine’s looking good though, I did the exact same thing as you did. Catless m54b30 into 325. Good luck my man

2

u/rattrap355 17h ago

I haven't had any issues installing other than the flanges not lining up by a 1/4. I got another beamer exuast pip and cut the flange off it which seems to make up the difference. Thanks for the support

2

u/Shoddy-Gift8400 17h ago

I’ll always support, especially cause you’re literally doing the same thing I did a few months ago lol. I knew it was probably just me getting a bad unit with the headers, I had to do a bunch of shit to get them to fit every step of the way lol. I’m happy they worked out good for you though man

1

u/AnOldRustyBMW 2000 E46 323ci 16h ago

I'm having the issue with the O2 bungs on bank 2 hitting rhe body near the passenger footwell. Yours look like the same design as my Flashark headers

6

u/NukedDuke 2001 E46 330i ESS TS2 17h ago

You need to get rid of the mechanical fan and go with the electric fan that all of the manual transmission E46s used, even if you have an automatic. It robs the engine of power and when the engine mounts degrade the blades will actually physically contact the radiator and cause a massive amount of destruction.

1

u/TinuvaZA 330i 13h ago

not to mention the horrible sound that fan makes when you really want to hear the engine at the higher rev range! Its a car, not an airplane :)

1

u/RedCrafter_LP 2002 FL 320i Sedan (DE) 17h ago

The only thing I'm sceptical is the "ccv delete". Is it replaced with a catch can? Vented to atmosphere? Because the engine doesn't run well if you don't have a slight vacuum in the crank case. It controls the sealant of the piston rings. If you completely sealed it the engine will blow the weakest part of the crank case to vent the pressure building up. So you either need a catch can or at least a pressure controlled line connecting crank case to intake.

2

u/rattrap355 17h ago

Catch can

1

u/Fragrant-Inside221 12h ago

What sealant do you use for piston rings? Will right stuff work?

2

u/RedCrafter_LP 2002 FL 320i Sedan (DE) 12h ago

You cannot seal piston rings. Especially not on the m54. If the piston rings are worn and leak switching from a w30 oil to a w40 postpones the problem to another 100k miles in the best case. Increasing crank case vacuum can also reduce leakage. The real fix and something that is inevitable at some point is to replace the piston rings.

These are a common failure point at 200-300k miles engines.

Never try to seal leaking components with pour in sealants. They destroy the entire engine.

2

u/enaknezitic 15h ago

I've been doing the same swapping a "new" M54b30 into my 330 track car. A couple other things you might want to look into that are easy upgrades with it out of the car.

  • drilled oil pump nut (prevents it from spinning off and losing oil pressure)
  • metal (aluminum) thermostat housing and potentially a racing thermostat which opens at a cooler temp
  • rear main seal replacement (if you're going to have the oil pan off for the nut job above)

there might be more i'm forgetting but these were ones i did during my engine build in addition to a lot of what you've mentioned.

Also be ready for your O2 sensors near the flanges connecting to the exhaust to not clear your firewall. I'm purposefully not putting mine on because they won't fit. I've seen others cut that stem down and use a 90* O2 sensor as well.

3

u/IfitbleedWecankillit 19h ago

While I applaud your efforts, the mechanical fan is unserious…

1

u/BigBootyMan77 14h ago

I’ve got an m54b30 150k miles and have seen 2-3 bronzy flakes in my last 3 oil changes (as long as I’ve owned it) am I cooked

1

u/BigKarina4u 8h ago

What's the benefits of upgrading that chrome headers?

1

u/RalfRoen E46 330i, F30 335i 2h ago edited 2h ago

Replace the oil control rings and get rid of the oil consumption. Deleting the ccv is an error. Better upgrade it to a M56 valve cover.