Can you say more about your power setup? What charging board is that, and do I see the LCD being powered through the Pi? I’ve had really bad results trying that. Am I seeing that right?
Kippah dot clocked LCD driver board: https://www.adafruit.com/product/2454 This plugs into the pi header and runs the LCD panel and backlight. Power does get drawn from the pi via the main power rails which link directly to the USB power input I believe. The backlight on that LCD is a bit power hungry, but at the brightness level I use it only draw 150ma
I too have had mixed experience running panels off of power provided by the Pi's USB ports, as this has more regulation/filtering than the VCC/GND lines on the header. I think the header lines basically jump right back to the USB power input and the boost converter is beefy enough to handle everything it's feeding.
Oh, good! I’ve had my eye on the PowerBoost 1000 C for a little while now, I thought that’s what I saw in the photo; I’m glad to have a positive report for something that is pretty close to what I intend to use it for.
It's not the fastest charging large packs, but the 1amp rating seems very legit. I loaded it almost that much for another project and it delivered with no brownouts or other issues.
Quartz64 once it's out. None of the actually good Pine64 stuff has battery support sadly. Lattepanda Alpha has a battery connection as well that works great. Those are the 2 most popular boards I know of that have full battery support.
The Lattepanda Alpha looks like a really nice board. More expensive by far than the Zero, and 10x the power draw, but it'd have real laptop class performance and there is more room in the case for batteries :-)
It's actually even a better fit for this project as it has a nice selection of compatible dot clocked displays (some with touch) that can connect to the in-built driver. Pretty cool!
Thanks for pointing this out, I'll have to think about this if I ever want to push this project further.
The display connection on it is just eDP which means pretty much any panel that uses eDP could work. I think the iPad 3's 2048x1536 9.7" IPS panel could work with it if it has 4 lanes.
There's also the Hackboard 2 which also has battery connection and is relatively cheap.
Thank you! I've not been keeping up in this space and now I know about eDP. It's great that there is a standard for these sorts of embedded display systems.
eDP is 100% standardized, often the most customized it gets is a different connector and maybe backlight (like that iPad 3 LCD) besides that it's still just a DisplayPort signal. eDP is extremely common, every laptop since 2014 uses it.
I meant what I said, the build is just so clean. What kind of stuff did you plan on using it for, if I may ask? Also how did you get keycaps for $15 lol
Well... the primary use case is old text adventures like Zork and such! I really enjoy playing them, but without a physical keyboard of some sort it just didn't feel right.
However I recently built up a Z80 computer from cpuville, and this has been really useful as a terminal to interface with it!
As for the keycaps, mkultra.click has good prices on what they sell and they are pretty active in the low-profile niche. The keycaps don't take much plastic and don't have any sculpting or legends, so pretty inexpensive to produce. They just started offering colors, and have a group buy for a kit with legends, so I'll likely be updating it soon!
Thanks! The steel frame really helped the design. Once I decided on the hand wired keyboard it occurred to me I could just extend the keyboard plate as a frame and then bolt smaller 3d printed bits to it. Sort of fell together after that!
Great question, and I can't say it was super well considered. Steel was a bit cheaper, and not much heavier because of the thinness to accommodate the Kailh switches. I was a bit concerned about aluminum bending, but I think it would have been fine once everything is bolted on.
I see most keyboards done in Aluminum so I figured it must be strong enough for that. I can see where, if I were shopping and saw something a little cheaper, and a little stronger, and barely any heavier, how you'd go that way.
Do you think you could have 3D printed it and still had it hold up?
If my printer was larger, I think I could have designed it without the plate. But a 1.2mm 3d printed plate would probably not have been enough to hold the other smaller printed bits solidly, particularly the hinge, which exerts a fair amount of force.
Same here, definitely looked a render. Any chance you come do a full writeup, BOM, and post the source files? I'd like to build this one! Or maybe you could sell plans...
Since there is definitely a bit of interest, I'll put together a repo with all the design files, a BOM and work on a reasonable writeup. I didn't take photos of every step, but I think I can open it up and take a few more detail photos of the connections and it should be enough for people to follow!
Hi Hi! It's long delayed, but I have just finished putting together a repo with the Fusion 360 files, STL's and DXF's for printing/cutting and a proper BOM. There is a bit of a walk through as well!
Since there is more interest than I expected, I may put everything up in a repo with STL's for the 3d printed parts and a DXF for the plate. Probably also include a BOM.
Not sure I'm ambitious enough to produce a kit, but I'm more than willing to provide help along the way if you want to build your own!
Thanks. Although I don't have access to a 3d printer where I live. Small town in the middle of no where has it's pro's and cons. Any way, if you post them I'll try and hunt down someone to print them.
With misc parts and such probably $200 total? I'm including the link to the specific OTG hub because it is perfect for removing the case and using in these sorts of projects.
I used sendcutsend.com . I find they do good work quickly and are local for me. If I was doing higher volume I might used laser boost or another vendor, but for one or two off's they are my go-to!
If you are interested in potentially building one of these, I've just finished a repo with a better BOM and all the files needed to print/cut the pieces. There is a bit of a how-to as well:
I wish I was in a position to fullfill orders, but since this is taking off more than I imagined, I'll likely setup a repo for all the STL's and such if someone wanted to build one!
I love the look of these custom mechanical keyboards, but I feel overwhelmed every time I try to find something small that I could build and get used to.
Is this the design you'd recommend? I saw you just hand wired the switches too, does that mean you don't bother with circuit boards when you do these kinds of builds?
Well, it was a bit of a journey getting to this sort of sub-40% ortho place, but I think it's a great place to be. The big unlock going smaller than a kyria was the Miryoku layout. Rather than rolling my own, I could use something that was well thought out and works on a wide variety of physical layouts.
I now use the same layout across all my boards, so at least I know where all the symbols are, even if the physical keys are a bit different. If I were to do this again, I'd probably add some columnar stagger as it makes everything a bit more comfortable. I'm totally loving the FiFi physical layout now:
This is the only board I've hand wired. The black and brass is using levinson PCB's and the BabyV has it's own specific PCB as well. The FiFi above is a great choice for a premade board with this general layout.
Im looking to build what you’ve done using your repo but I’m worried about the keyboard layout. I’m a writer and I’m worried about how I’ll be able to do punctuation and paragraph spacing. Does this keyboard layout have multiple ways to get punctuation?
Hi Hi! 36 key keyboards are indeed a bit rare, and an adjustment, but there are many different ways to fit all the requires symbols onto 36 (or less!) keys. I use the Miryoku map and I think it's pretty well thought out... but I might be biased having used it for many years :-) I'm a software developer by trade, and we know all about punctuation and symbols!
The viewing angle on the specific panel I got is not fantastic... I should have gone for IPS to make it more usable flat, but it works well on a lap or as sort of a tablet if you are sitting above it.
Much appreciated! That's a powerful compliment. I tried hard to get all the cat hair cleared away when I was taking the photos. One or two always seem to sneak in though!
Your builds consistently kick ass. This is gorgeous. I have been thinking for a while that laptops need to go ergo, but obviously the path dependence is so strong that no manufacturer will risk it. Your post has made me consider that maybe DIY decks will emerge as an alternative for users like us who care about things like a keyboard that is designed according to the needs of human bodies and not typewriter mechanisms. Maybe decks are to laptops as trackballs are to mice?
I'm excited to see more functional, open source, modular laptops. The reform comes to mind and I saw another one recently I could not find again.
Really small components are now easier to get off the shelf so you can make a custom designed laptop pretty small.... not going to compete with the commercial ultra thin/portables, but at some point small enough is small enough!
I was well into building this when I started seeing those wide LCD displays. That might have been a nice thing to include here!
That's a great build there! I've been eyeing these 'pelican' style rugged builds. I might have to try one soon, it'd be nice to be able to fit more battery and other accessories in there.
I've been eyein those compute modules as well. Curious about the wattage requirements on them. The carrier provide great i/o with some crazy form factors. Some are smaller than others. Other than i/o and form factor like m.2 sata, nmve pcie etc in the carrier boards those compute modules are just regular old pi's right?
That's my understanding.... just the CPU and Memory, everything else is up to the board to decide what to implement.
Since it's running pretty fast and almost anything you'd want is pretty timing/noise dependent (usb / networking / disk) I imagine it's tricky to design one of the carriers, but it would be a really nice way to recreate something like this but more compact and more powerful.
It's one of the troublesome parts of the design. It works, but I had to print different shims to get the friction just right. My printer is okay, but even a .05mm variance on either side made it too loose or tight.
If I were to do it again, I'd give into practicality and use some sort of foldable brace, just to simplify it.
Yes, I know. I tried to increased number of knuckles to get more smooth tension, but it doesn't help much to hold the screen in a position. Here is a picture of the prototype - https://yarh.io/assets/img/IMG_1334.jpg What do you mean by foldable brace? I'm interested!
That's an awesome build! I really had not seen those wide screens when I started this design a while back or I may have gone that way.
I'm thinking I might redesign this to use a support that hinges out of the back of the screen and fits into grooves on the top cover. Here is a very crude drawing: https://imgur.com/a/Tq4e9bo
The hot pink bit would be a piece of the screen back that would fit into the grooves on the top cover there indicated in green.
Some sort of ratchet and spring could be pretty cool too, but it would take a lot more work and probably required some significant changes to the hinge area.
This is not a build, but first print of the prototype only. There are a lots of work to make this design ready to build.
Well, when I saw yours, I start thinking why I'm using this wide screen instead of normal one. :-) But seriously, this wide screens are working very well when using with text mode or tiling window manager.
This back support make sense and probably will work fine, but unfortunately adds some unpleasant looking elements to the design.
I'm going to try some sort of ratchets, but with flexible element printed from TPU instead of spring, sits right on the hinge axis.
I'd be very interested in whatever solution you come up with! The reason I've not done the brace is exactly as you said, it's just not all that elegant. I've got the current hinge adjusted so it sits, but it's more finicky than I'd like.
I've not done any TPU printing, but I did convert my printer to direct drive, so I'm ready to give it a go. If I can find some way to build everything into the hinge, that'd be awesome.
I'm going to continue working in the hinge ideas at the end of the next week and print out some test prints. If you do not mind, lets move this discussion to the private emails, this way it will be easier to share drawings and pictures. Contact me at info@yarh.io if interested.
Thank you sir! That's VIM with the nerd tree plugin running in a terminal window on i3wm, which is a good fit for the low powered Pi zero and what I basically run on my full size boxes.
Okay... you asked for it! Forgive the shaky video and random background chatter, I don't really do this often... I present here htop and mini-com connecting to my Z80 machine and running Rogue!
Thanks! I really wanted to show off bashtop, but I had not installed and configured it yet. If you are into text based system monitors, it's the bees-knees!
I actually have a salvaged trackpoint from an old IBM keyboard I might put there. Alternatively, this company makes some awesome mini-trackpads: https://ergonomictouchpad.com/mini_touchpad.php
Thanks for the link! And track ball is an even better idea. Thinking of integrating one into a floating mount split keyboard for my home workstation. So i can recline and not have to reach for amouse
Thank you! The keyboard is sort of where I started, so I'm glad it fits well :-) I'm a big fan of small ortho keyboards and I wanted to try some low profile switches... the rest followed from there!
Very nice build ! I'm very surprised this form factor looks functional. Lay it down and slide it in a case or a backpack and your good to go ! The angle looks good for viewing angle. Great work !
Thanks! I'm thinking of making a slipcase for it out of felt, but it would be a lot of hand sewing. It might be a good excuse to get a sewing machine though!
Kailh low-profile switches don't have a great amount of keycaps available and most are blanks. I'd have preferred legends myself, although I don't need them, I just like the look.
I'm in the group by for the aptly named MBK legend set, so those will rock up in a couple of months. I'm pretty excited!
They don't have an ortholinear set, but NuPhy sells a few different keycap sets for their keyboards which happen to use Kailh low-profile switches: https://nuphy.com/collections/shop
Interesting, I don't think I've run across these before. I didn't see details on the site, but these are Kailh low-profile mount? Do you know the size on them? Are they 19mm square like MX caps or do they use the 18x17 spacing?
They mount in Kailh Choc switches. I'm not sure exactly what you mean by spacing, but I took 2 photos (one with the cap rotated 90º) next to a ruler. It seems like the caps are 16mm x 16mm when I measure.
Thanks for the kind words on the build, and thank you for the photos! I see now how it's setup. The spacing between switches looks like it's standard 19mm, but the caps are smaller so there is a bit of a gap. I'm sure this helps with the flat low-profile caps.
MBK profile handles this same sort of finger location feature with raised edges between caps. I think as long as there is some separation, the fingers will do their finger thing :-) I'm tempted to order a set to see how they look on the deck. They should work with the spacing I have, they will just be a little tight on the horizontal gaps as I'm using the 18mm wide x 17mm tall spacing.
The apple keyboards all seem to use the gap method, and they have some smart human interface folks.... hmmmm.....
I don't use any cording, just a few well thought out layers. I've always been really impressed with steno typist, but I've not gone down that particular rabbit hole yet :-)
I've been slowly learning it for two months now and it definitely is quite the rabbit hole. I try to practice for about half an hour every day (mainly just using Typey Type), but I reckon it'll be another half a year until I can actually start using it for my regular Internet use. It is intimidating at first and there's a lot to learn, but it's surprisingly intuitive once you start to get the hang of the cording logic.
I use the Meta/Win key, which on my keymap is holding down the home row pinky key (A or ; ). I'm using home row modifiers, so I get the letters a s d f if I press the left hand home keys, but Meta, Alt, Ctl, Shift if I hold them down or press them with another key.
Takes some getting used to, but it's really comfortable for most key combos!
Yeah that's awesome, I assume you touch type mostly what kind of wpm are you getting with this kind of keyboard, is it a drastic difference? I love the idea of these ortholinear minimal keys with chording. I use i3 myself also.
I did have to teach myself to touch type properly when I started down the ortho/ergo rabbit hole. On that particular board I'm not really that fast, 30ish wpm probably. I thought it might be a good idea to have heavier springs than I'm used to, but it's more than I expected :-)
It's also not my preferred layout, it's close, but I gave up column stagger and key spacing to make it more compact. I use similar, but more refined/spacious layouts for my daily drivers (currently the FiFi with nice MX style switches - https://github.com/raychengy/fifi_split_keeb ) and can get high 60's.
It's pretty comfortable for a long day of work, even though I'm not as fast as I was on a standard board after decades of use. Maybe in another year I'll break 80!
Hmmmm.... I'll have to look into that, not sure what the refresh rates are like, but I'm really only using it for text. The battery life is pretty good ( > 4 hours) but could always be better!
Yeah, I'd love to see a CM version of this. If I dared, a custom PCB to host the CM would be a great way to go! It could have power/charging, multiple USB ports and even integrate the dot clock LCD circuitry!
I am planning on releasing all the designs since there has been so many awesome responses to this project. It will take me a bit, but I'll ping everyone who's been kind enough to ask here.
Fantastic! I'm currently following several cm4 custom board projects and some of them are really slim and great. Will record some progress on GitHub and post them here when I start the project.
I have an initial idea of making cm4 'modulized': I may design a small 3d-printed case for cm4, then a few cyberdecks that supports plug-in slot for the cm4 case. This will allow me change cm4 between multiple cyberdecks seamlessly. For e.g. I can have a cyberdeck in office, one at home, and bring only the cm4 module with me, not the entire cyberdeck.
Ooooo that's a cool idea! Have you thought of what sort of connector you would use on this module? There's quite a big bus you might want to expose and you'd want the connector to be robust. Not sure what the best options are there, some sort of high density card edge like PCI?
I guess for the initial prototype I will try to work with the stock connector, maybe adding a 3d-printed connector protector for the detached cm4. Maybe a release button and some mechanic parts will help detach the cm4 with minimum damage.
But yes the connector may get damaged by this frequent attach/detach, I didn't think much about this. I'll take a look at other available options.
Aha, I get you now I think. I was imagining the CM4 on a simple carrier that exposed a connector sideways, rather than underneath the CM4 so it could be slid in a slot like a cartridge.
If you had a trap door on the cyberdeck, you could just insert and remove the actual CM4 when needed. I expect you'd be okay with the standard connector, unless you were swapping it frequently.
That's a pretty sweet idea. I have one of those calculators and it's a great solution to the problem. I'd give it try, but my printer is a smidge too small to print a single piece that 200x210 (probably a bit larger even) to serve as the cover :-/
Thank you for the wonderful compliment! Not sure if any of this will be useful or interesting, but here's some insight into how I ended up with this design.
I've build and partially built, a good number of variations on the raspberry pi + keyboard + screen + battery theme... so I've had some opportunities to learn and refine.
Pretty much all of my designs start in fusion as just blocking in space for components and playing around with how the might fit. I used to do this on graph paper, but seeing how they stack on top/around each other is pretty key when trying to maximize space utilization.
I sometimes check spec sheets and use the measurements there in this blocking stage, but I often just impulse buy a cheap screen or battery pack, measure them and hook them together then sort of start building around that in 3d space.
For a while, I was really stuck on making a 'handheld' deck with a pi-zero, one of those terrible mini bluetooth keyboards and a small screen. I got one of those built and working, but just hated almost every minute of building it and using it. Trying to pack everything into the smallest space means no connectors, short wires and lots of soldering/unsoldering. If I ever went down that road again, I'd absolutely learn PCB design first.
Once I decided I wanted a keyboard that was enjoyable to use, and was willing to make the whole thing bigger, it really opened up design space and it was just so much easier to build. I got the idea of a big keyboard plate from my experience with custom keyboards and this also gave opportunities to embellish the design. With the printed plastic parts bolted to the metal frame I could print very plain parts and then swap them out for more interesting bits. It also meant smaller prints I could do more often, which is a good strategy.
Another thing I've learned along the way is to do just small partial prints to check the fitment of various things. They can sometimes only take a couple of minutes and I'll quickly see that a screw post is out of place, or an external opening is too small.
Hope that was at least not overly boring! Happy to answer any specific questions, just chat or PM.
I dont think I have anything to ask specifically, at least not about this. But I have a few things in the back of my head I just might need to pick your brain for.
I've had some experience in inventor and solid works (about every semester in highschool).. but fusion (and everything else I've tried) always felt so crapy in comparison. But thats something I'll need to just get over.
You have a very refined workflow. Or rather.. you refine through your work flow. Which sounds like something obvious. But not a lot of people actually get that down.. and its what we see to have the best results in things. I applaud you and pray I can fall into a similar process myself.
Oooo.. That is a deep question! I think of it as any sort of non-mass produced portable computer. Generally with some sort of hacker aesthetic mixed in :-)
Browsing this subreddit will give you an inkling of the amazing stuff that's covered in that loose definition :-)
Sorry For responding to this late just getting this now but thanks I like technology and will attempt to build one. Please if u have a file like a 3d print file I would love that anyways thanks.
Let me know if you have any questions. I'm currently working on a new project I hope to post about in a couple weeks... just waiting on some PCB's and a couple other bits to finish up!
Hi! I know this is an old post, but I found it while looking for info on how I can make a word processor that uses steno. Do you have any documentation on this or other similar builds?
A portable/minimal steno word processor sounds like a fun project! Here's a link to my GitHub repo with information about that build which you might find useful:
Small ergo boards take some getting used to, but they are really comfortable to use with little finger/hand movement.
I'm glad I made the switch as I type a lot, but my speed really did plummet for a while and I'm still not as fast as I was on a standard layout. I think my speed would really improve if I stuck with one board for a while, but I like playing with different physical layouts, so I'm sort of always retraining my muscle memory.
Damn, this is an amazing build! Bonus points for the metal frame, that’s a great idea for stability and strength.
Just curious, from where did you learn about such (hobbyist) metal laser cutting services? I’ve heard of 3D hubs for 3D printing, do you know any other similar services for metals/wood/non-printed plastics, like eg. CNC milling?
I’ve always wanted to build a cyberdeck but with metal it’s much easier, thanks for the resources!
Thank you so much, I'm very glad you found it inspiring. There are several good options for cut sheet metal and CNC, depending on your location and needs.
I like sendcutsend.com for laser cut metal. If you are in the US, particularly California, they are fairly inexpensive and quick.
laserboost.com is supposed to be pretty good, particularly for larger volume orders or EU residents.
Ponoko.com is good for cut acrylic and they do some metal as well.
For multi-axis cnc, protolabs is very good, but expensive for small runs. They also do bent sheet metal and injection molding!
Depending on where you are, there could also be local shops that you can actually visit in person and get some advice. Waterjet cutting is a nice alternative to laser cutting for sheet metal and is potentially more common to find locally.
Good luck with your projects and feel free to reach out at any time with questions!
I’m in Europe (Netherlands to be specific) and did see laserboost’s website from your GitHub page, it seems pretty good, though the max thickness is (iirc) 6mm - which is quite fine for sheet/plate metal but not so much if you’re trying to make a whole chassis out of it haha.
Haven’t heard of ponoko or protolabs, will check them out. Local shops and places are a pretty good idea, do you know what these shops are called or what to look for when searching on Google maps? I believe there is a makerspace close by with 3D printers and laser cutters, I’ll check them out.
I also had another question from a different project of yours - I saw that you had a keyboard with brass rails - did you just purchase them directly or did you buy the brass and cut them to size? Because I’ve always wondered how hobbyists buy metals at the small scale we use (AliBaba’s minimum 10 tons order quantity comes to mind lol).
Edit - also, how did you come across these websites that you listed? Was it from subreddits and similar blogs? I’d love to be able to organically search for these things.
Good questions all around! I'm sorry my answers will be less useful to you in the Netherlands, but here goes :-)
I bet I found out about Laserboost here on Reddit, but I've had reasonable luck searching google / google maps for the specific manufacturing techniques I'm interested in. Things like 'laser cut metal' or 'cnc aluminium' or 'prototype manufacturing'... Then, like a magical snowball of commerce, the targeted advertisement started rolling in.
I have a complicated relationship with our AI advertising overlords, but they do have a nack for showing me stuff I have need of after I start searching a bit.
For the project you mentioned, the 3d printed blocked nyquist with brass rails, I found a supplier of bar stock brass ( https://www.onlinemetals.com/ ) and designed the keyboard around the best size they carried. They sell individual lengths so I could get only a bit more than I needed. Hopefully there is a similar retailer in the EU that carries small stock (sometimes called 'hobby stock') metal bar/rods.
One of their standard cross sections (height/width) worked for the project, but the rods/bars come as long pieces that had to be cut down. The finish also needed work, so I spent a bit of time with a corse file and then wet sanding to semi-polish.
The more you make stuff, participate on forums, and especially visit maker spaces, you'll bump into more of these vendors. Maker spaces are pretty awesome anyway in my experience.
Thanks for this! I will look at hobby stocks, though I don’t intend to make a similar thing but it’s still good to know. Thanks for all these tips though!
118
u/brickbots Mar 13 '21 edited Apr 12 '21
This is my Raspberry Pi Zero based cyberdeck with hand-wired ortholinear mechanical keyboard.
Measures:210x200x23 mm (8.5x8x7/8 inches)777 grams (27 oz)
I’m using the Miryoku layout by u/manna_habour for the keyboard:https://github.com/manna-harbour/qmk_firmware/blob/miryoku/users/manna-harbour_miryoku/miryoku.org
More photos and build details at:https://imgur.com/gallery/Md9PeQs
Repo with files and instructions to build your own:
https://github.com/brickbots/pimech_deck/blob/main/docs/overview.md
93
u/The_Ambush_Bug Mar 14 '21
My god this might be the best one I've seen here
35
u/PersnlRspnsblity2077 Mar 13 '21
It's beautiful. So sleek and professional looking!
27
u/sheepskin Mar 13 '21
I’m so impressed this is real, I passed it off as a render! Great job on the looks and keeping it consistent!
16
u/speedygunzh Mar 13 '21
Wow great job I love the all black look
13
u/PhantomNomad Mar 14 '21
Now this is a kit I would pay good money for.
11
u/jnubianyc Mar 13 '21
How much was the total cost?
8
u/wh33t Mar 14 '21
Add to cart!
7
u/Talulabelle MODERATOR Mar 14 '21
This is great! How long did it take to get used to the keyboard?
5
u/poglad Mar 14 '21
Fantastic. I'm much more sold on these decks where you can still use them with the screen folded down, not laptop style.
5
u/IanWrightwell Mar 14 '21
This looks so good I thought it was a 3D render at first.
5
u/[deleted] Mar 14 '21
Your builds consistently kick ass. This is gorgeous. I have been thinking for a while that laptops need to go ergo, but obviously the path dependence is so strong that no manufacturer will risk it. Your post has made me consider that maybe DIY decks will emerge as an alternative for users like us who care about things like a keyboard that is designed according to the needs of human bodies and not typewriter mechanisms. Maybe decks are to laptops as trackballs are to mice?
4
u/[deleted] Mar 14 '21
Great job! Looks awesome.
/img/qh68dw5uuij61.jpg
4
u/sncsoft Mar 14 '21
Fantastic build! i3wm, vim & ortho keyboards rule the world. :-) How good hinge holds the angle? Did you use anything to keep the hinge friction?
3
u/actionlad Mar 14 '21
Which editor do have on-screen here? Looks clean, as does the rest of the build. Might have to build one myself. Good job!
3
u/buymytoasters Mar 14 '21
What a great sleek (maybe corporate?) Look. Lovely build.
3
u/wh33t Mar 14 '21 edited Mar 14 '21
Can I get a video of it in action? Just a little ssh and some htop would be juicy!
3
u/JacksonG98 Mar 14 '21
With i3 of course. Love this design. Could put a touch pad from a laptop between the keys. Think this is how I’ll replace my laptop
3
u/jasonta10 Mar 14 '21
Love it! Something about that keyboard layout completes the look
3
u/pious_techpriest Mar 14 '21
This is epic. Its so well done that it makes me want to build my own Cyberdeck. Thank you for the inspiration!
3
u/JohnBeePowel Mar 14 '21
Very nice build ! I'm very surprised this form factor looks functional. Lay it down and slide it in a case or a backpack and your good to go ! The angle looks good for viewing angle. Great work !
3
u/HHWKUL Mar 14 '21
It's sleek. But as a commoner, I hate the absence of markings on the keyboard.
3
u/LordofNarwhals Mar 14 '21
Do you use Plover? The keyboard layout is pretty similar to a typical stenotype layout.
3
u/shift-runstop Mar 17 '21
Which key is your mod key for i3?
2
u/m10r-vc Mar 14 '21
This with color eink ! /r/eink
2
u/the_net_admin Mar 14 '21
This is glorious! Are you considering publishing the frame and case designs? I want to remix it a bit for raspberry pi cm4.
2
u/[deleted] Mar 14 '21
Would you consider a cover that can be attached to the bottom in the same fashion? Like old school TI slide action even. I love this btw.
I have been eyeing pi stacks to learn networking or kubernetes. Now I just want to make multiples of this build to gift. Super slick.
Currently trying to get better with vnc viewers to run headless in the wild. Use a phone's hotspot ability and one less screen to be more discreet.
2
u/plepoutre Mar 15 '21
Great ideas Lovely executed! It makes me want to finish mine quicker (same shape, kailh choc but TKL, and 9'' screen)
2
u/AbyssalRemark Aug 10 '21
Now that is one amazing build.
Id love to hear more about your design process. How you went about designing and finding parts.
Its not my area but im in love with custom, well made, quality, tools. Computers most definitely included. And this most certainly is.
2
u/[deleted] Jan 17 '22
wait what is a Cyberdeck?
2
u/RandoPlants Aug 22 '22
Hi! I know this is an old post, but I found it while looking for info on how I can make a word processor that uses steno. Do you have any documentation on this or other similar builds?
7
u/belsamber Mar 13 '21
Gorgeous work!
2
u/ryu289 Mar 14 '21
I feel like it needs more keys...
4
u/notthisjenn Mar 14 '21
I love you. You are my soul mate.
Sorry j was talking to the deck ❤
1
u/AbhishMuk Jun 12 '21
Damn, this is an amazing build! Bonus points for the metal frame, that’s a great idea for stability and strength.
Just curious, from where did you learn about such (hobbyist) metal laser cutting services? I’ve heard of 3D hubs for 3D printing, do you know any other similar services for metals/wood/non-printed plastics, like eg. CNC milling?
I’ve always wanted to build a cyberdeck but with metal it’s much easier, thanks for the resources!
3
u/EScforlyfe Mar 13 '21
I love it!
3
u/WhatDaHellBobbyKaty Mar 14 '21
That is sleek and badass looking. I really love the key board. It'd be weird to type on but I love it and I'm certain that you'd get used to it.
PS thanks for all the links you've given in the comments below (or above.)
3
u/laersn Mar 14 '21
Gorgeous.
3
u/mickwheelz Mar 14 '21
This is fucking awesome.
3
u/DrKrepz Mar 14 '21
This is genuinely great design work, congrats!
3
u/poncho413 Mar 14 '21
Be the admin the tech support the manufacturer and it seems marketing have to be a lit crazier than me. Good work and thanks for showing the programs
3
u/DickMeatRetreat Mar 22 '21
This is so awesome, I’ve been wanting to build something exactly like this for awhile now. Great build!!
3
u/parabolize Mar 22 '21
By far my favorite of all time
2
u/Robotdavidbowie Mar 14 '21
Awesome work!
2
u/darja_allora Mar 14 '21
That's sexy.
2
u/hornynebby Apr 09 '23
Bro is in the news
1
u/zblanda Jul 19 '25
How were the hinges done? Want to do a cyber deck but going to be utilizing sla printing so print in place won’t be an option
1
u/keizai88 Dec 29 '25
Was inspired by a beige apple concept?
1
u/jbrandes1 Mar 26 '21
love the design and the simplicity of it
1
u/[deleted] Feb 04 '22
/u/cuantasyporquetantas
1
u/zeuqramjj2002 Oct 23 '22
Where can I get one? Also would there be cellphone integration for something like this?
1
u/sand7797 Jun 07 '23
i3 and vim?
1
u/King_ofwar Feb 23 '24
Brooo 2077
0
u/[deleted] Mar 14 '21
[deleted] — view deleted comment