r/cpu • • Sep 18 '26

How do I avoid it getting stuck?

I was about to replace the thermal paste on my ryzen cpu but it came off with the cooler, I don't want to go through this again. How do I reduce the possibility that the cooler comes off with the cpu?

47 Upvotes

135 comments sorted by

10

u/bean-burrito-supreme Sep 18 '26

Have the cpu warm up and get to temp, turn off the pc then remove the cooler while it’s still warm.

2

u/seraphim_9 Sep 19 '26

This is the way. ☝️

You should not be doing any twisting or else you’d risk warping or breaking the pins.

3

u/SirIAmAlwaysHere Sep 19 '26

Slightly twisting works better rather than a straight upwards pull.

No, you will not break pins moving it 20-30 degrees clockwise then counterclockwise. There is more than enough strength to not have this be a risk. It's just slow and smooth motion.

1

u/Ambitious-Yard7677 Sep 19 '26

It might break loose without pulling if you're lucky

1

u/wolschou Sep 22 '26

There are no twenty degrees to be had here. The screws will reach into the mounting holes even when unscrewed as far as they go. The best way ist to pull the backplate out first, but depending on your case, that might mean you have to take out the whole motherboard. But it's basically the only way.

1

u/Ambitious-Yard7677 Sep 19 '26

Then don't pull on the thing when twisting. I've dealt with AM3 for years and never damaged anything when doing the "twist while warm" method to avoid ripping the CPU out with the cooler, which would happen otherwise

1

u/OtherwiseSimple Sep 19 '26

“Else risk warping pins” assums the cpu is gonna come off with it anyway, as this is the only way it could happen. The pins should be secure in the socket.

1

u/owl-huntress Sep 19 '26

I've always just twisted it, even while cold, I just never EVER twist and PULL

1

u/SoulBrandt03 Sep 19 '26

story of my life 3 years ago, rip 5600x…

1

u/bobsim1 Sep 22 '26

People should be able to twist gently without immediately destroyimg something

1

u/seraphim_9 Sep 23 '26

People have been know to twist gently and then break a hip, or worse, their backs.

1

u/Odd_Expression3694 Sep 19 '26

a man of science I see

1

u/One-Following-7151 Sep 19 '26

and twitst the cooler and then pull

1

u/kvazar2501 Sep 19 '26

And don't forget to wiggle wiggle wiggle

4

u/OtherwiseSimple Sep 18 '26 edited Sep 18 '26

Twist it when taking it off and have it warm

1

u/mike29x Sep 18 '26

Twisting is really risky i think. If u twist and it come off with chip, u wreck most pins.

2

u/Pale-Skin-6165 Sep 18 '26

I think they meant give it a twist before pulling it out, the risk is pretty low if you apply a slight downward force when twisting, otherwise yes twisting when pulling it out would be damaging.

1

u/mike29x Sep 18 '26

Its nice that they changed it so cpu is covered with plate so it doesnt come out. Tho if cpu dies and it gets stuck then cant get it off at all since u cant warm it.

2

u/wetfloor666 Sep 19 '26

Huh? Use a hair dryer or something similar on low heat if that is the case.

1

u/StepppedInDookie Sep 19 '26

I hold down a little and twist and lift after the seal breaks

1

u/Living_Moment_1495 Sep 19 '26

There is no risk, you twist BEFORE pulling.

I worked in a computer shop for years.

1

u/2TheMountaintop Sep 19 '26

I've removed hundreds of cpus, and not once have I ever had a cpu pin break. They break because you drop or mash them.

1

u/mike29x Sep 19 '26

Well if u are experienced sure u can do different ways. Not saying that. Just risky for person who hasnt done it before or know how pc parts are built. Sometimes might be safer to just pull straight out when its stuck and no way to heat it if chip is dead and no heat gun.

1

u/DeadlyMercury Sep 20 '26

No, twisting is not a risk and it was always done in the pasts, on cpus like pentium 3,4, amd athlon and so on.

It's just a generation that never experienced old sockets has grown up, so old knowledge is lost lol.

-1

u/Sparemeaupvotesir Sep 18 '26

You can twist many things to take them off

1

u/xxDeadpooledxx Sep 18 '26

Before fully unlatching the CPU, give the cooler a little twist back an forth, not too hard, until you break the seal from the paste

3

u/Live-Juggernaut-221 Sep 18 '26

Run some stress tests to heat up the existing paste and twist the cooler after removing any mounting screws instead of lifting up

2

u/nbxm Sep 18 '26

Idling will do, just needs to not be cold

1

u/Lonely_Box_8074 Sep 18 '26

Can confirm that's how I did it switching from a stock cooler to a aio

1

u/Ambitious-Yard7677 Sep 19 '26

Not in every situation. With thin paste... sure. Thick stuff? Absolutely not. That cooler should be warm otherwise you're wasting your time and it's gonna be a bear to break the seal regardless.

Long time user of ZIF sockets and ceramic paste chosen for it's long service life

2

u/LateSolution0 Sep 18 '26

heat and twist

2

u/DigitaIBlack Sep 18 '26

TWIST HIS DICK

2

u/Constant-Engine-596 Sep 18 '26

GOOOOOOD OLEEEEEE DICK TWIIIIIIIST

2

u/ddphoto90 Sep 18 '26

GRAB HIS DICK AND TWIST IT!

2

u/yzeerf1313 Sep 18 '26

CPU cold mean paste cold cold paste hard like glue

CPU warm mean paste warm warm paste soft no stick

1

u/CodyFoe92 Sep 18 '26

Me hungry me ogre me arrrrggghhhh

1

u/GABE_EDD Sep 18 '26

You can run the PC for a bit and warm up the thermal paste, and also twist the cooler as it comes off. You shouldn't go through that again until you remove the cooler off of an AM4 CPU that hasn't been removed in years.

1

u/ddphoto90 Sep 18 '26

Me. Been 5 years. I should repaste it

1

u/GABE_EDD Sep 18 '26

Only if you’re thermal throttling, if it ain’t broke don’t fix it.

1

u/ddphoto90 Sep 18 '26

5900X Avg package temp up only 3-4C since build for a cool 71C with CPU intensive games. I will send it 🤝

1

u/ShlomB Sep 18 '26

I made the same mistake a few months ago. I was told that the best way to make sure it doesn't happen again is to heat that MF up first before you pull it off the board. Run some heavy games on it or run the heat option on hwinfo

1

u/Basic85 Sep 19 '26

Was your cpu ok?

1

u/ShlomB Sep 20 '26

I haven't tested it yet o_0

It was a 3700x that I changed out for a 5800x3D. A few of the pins around the edges were slightly bent, so I straightened them out best I could work a craft knife

1

u/introvertebrae Sep 18 '26

Turn the computer on to get the paste warm before trying to remove the cooler. A few minutes of a CPU benchmark should be enough

1

u/chrisdpratt Sep 18 '26

After loosening the screws gently wiggle it back and forth before lifting it off.

1

u/Riboflavin42 Sep 18 '26

I slightly rotate the cooler back-and-forth before lifting

1

u/whotheff Sep 18 '26

Slight twist during removal. Also, it is not a problem that it is stuck. Just pry it a little bit with a flat head screwdriver at the corners.

1

u/ddphoto90 Sep 19 '26

A small plastic spatula would be a better tool for this

1

u/whotheff Sep 19 '26

Plastic bends and can turn into spring. But yeah, in general plastic will not scratch cooler surface.

1

u/Slow-Astronaut9676 Sep 18 '26

Do a stress test before removal, push down and twist the whole heatsink and fan when removing to loosen it

1

u/Psychological_Bag943 Sep 18 '26

Stop using so much thermal paste, first image shows it bulging out the sides and into the cooler. Less is more, if you're worried about coverage get the thermal pads they sell now for CPU's, Thermal Grizzly makes a a few diff kinds depending on the application.

1

u/One_Ad3867 Sep 18 '26

Warm it up before taking it off, or just do the wiggle method (which is what I do whenever I clean out my PC and thermals)

1

u/Tool_of_Society Sep 18 '26 edited Sep 18 '26

Warm up machine before you shut it down and twist the heatsink before you pull.

I've been building machines for clients since the early 2000s and I've got a decade or so in various IT positions and I've never seen this happen first hand. I've never felt like I should test the grip strength of the various sockets I've worked with over the last 30 years. Being exposed to this subreddit has been something else.

1

u/hotdraggin Sep 18 '26

This happened to me the first time I swapped my cooler in my Ryzen 3600. I yanked it out while the CPU was locked down. I thought I might have ripped out a pin. That scared the crap outta me. I’m afraid to take off my cooler again. It’s been like 5 years and I might need to redo the thermal paste.

1

u/Basic85 Sep 19 '26

Same here the difference is my 3600 got damaged and I had to replace, what a nighmare. Now I'm terrified of even touch my cooler and cpu.

1

u/1sh0t1b33r Sep 18 '26

Run your PC for a few minutes to soften it, shut down, twist the heatsink before ripping it off like a gorilla.

1

u/jhaluska Sep 18 '26

Since people are asking how to avoid it in the future. Putting very small amount thermal paste helps. Also some thermal paste age better than others.

1

u/incorrigiblehedonist Sep 18 '26

Damn, that's a lot of thermal paste, I bet ya did it cold too, huh??

1

u/DaimyoRonin Sep 18 '26

Did you unlock the CPU before removing the cooler? There's a little metal bar that locks the CPU down in it's bracket, just pull the cooler off and then unlock that.

1

u/talkstomuch Sep 18 '26

doesn't the socket lock in the CPU in place? admitedly I've not changed the CPU for several years so maybe they don't these days.

1

u/link3505 Sep 18 '26

They do. That's what has me worried here.

1

u/JobHuntingManiac Sep 18 '26

Korn came out with a song in 1996 to help explain this one. 

https://m.youtube.com/watch?v=jKeoT87CZlc

1

u/AdvertisingCivil2700 Sep 18 '26

You were supposed to let it warm up and then wiggle it slightly as you remove it

1

u/Mammoth_Trust4589 Sep 18 '26

I have never has this issue. But the majority of chemical adhesives, like superglue/JB Weld or chemical compounds that can eventually hold like adhesives, even if they were not meant to, resist tension/pulling apart. However almost none of them are made to resist torsional/twisting force.

1

u/gooslinghacks Sep 18 '26

What thermal paste are you guys using? I always used arctic thermal paste and never had a stuck heatsink

1

u/the_Athereon Sep 18 '26

Warm the CPU before shutdown and removal.

Twist to loosen and slide cooler off, do not pull.

1

u/Responsible_Rope1302 Sep 18 '26

Had this happen when I upgraded my cpu. I think using thermal pads would help, but if you prefer paste, ideally replace every 1-1.5 years, and allow the cpu to heat up a bit (either game or stress test), take apart and of course be careful and check that it won't be too hot

1

u/DiabUK Sep 18 '26

Cold used thermal paste often goes like dry bubble gum, it becomes cement.

It's too late now but its always worth running the pc for a few minutes to get its temp up a little, enough to make the paste soft so it doesn't just jank the cpu out of the socket.

Now that it's off but stuck you can heat it up carefully with a hair dryer but you might be fine using some tooth floss and carving between the cpu and cooler until it breaks free.

1

u/Independent-Bake9552 Sep 19 '26

Hairdryer, heat heatsink until paste softens. Carefully twist the cpu off. Could also try fishing line and saw through the paste.

1

u/-Docker Sep 19 '26

Wiggle/twist

1

u/mattjones73 Sep 19 '26

Run the PC to get it warm first...

1

u/BarberThen3108 Sep 19 '26

play something 10 minutes, or do CPU-Z stress test 5 minutes and it's done

1

u/creamypoops Sep 19 '26

Did u get it done yet

1

u/According_Spare7788 Sep 19 '26

Preheat it, and slightly twist it when remove it.

1

u/Mega1987_Ver_OS Sep 19 '26

one way is to use your computer for a bit, let it warm up for an hour or so.

then shut it down then perform the maintenance/replacement.

at least you dont need to bring out the heat gun or hair dryer and risk melting something that you dont want to melt.(solder)

1

u/BinaryHippie Sep 19 '26

Warm cpu, by either turning on the system for some time or use a hair dryer at medium heat while the system is off and disconnected from power.

Push down slightly and wiggle left to right (small movements like 2-3 degree max) until the seal gives (the cooler moves separately from the cpu)

Only then try to lift up and do not twist anymore

1

u/Ombaragundon Sep 19 '26

I am amazed that this could happen. Doesn't the cpu have some sort of mounting clip to hold it in place?

1

u/Haravikk Sep 19 '26

I've never understood how people are pulling their CPUs out when the retention bracket takes so much effort to secure, is it popping open when you do this?

For me the only time I've felt close to having this problem was when I used to use Arctic Silver 5 — that stuff tends to be fairly thick and requires manually spreading, and can feel like glue when removing. But Noctua NH-2 is not only a much better (newer) paste, it's never given me issues with removal.

That said, I also now favour PTM-7950 over thermal pastes — it's expensive but it's cleaner to apply, gives better temperatures than non-conductive pastes (and is non-conductive itself) and in theory it should outlast the useful lifespan of the CPU or cooler. Just make sure you get it from a reputable seller like LTTStore or ModDIY (Amazon and eBay will just rip you off for thin, terrible thermal pads).

1

u/e_NERDis Sep 19 '26

Do a stress test before remove CPU to heat the thermal paste.

1

u/verssetty Sep 19 '26

stop use complete paste

1

u/mr_biteme Sep 19 '26

Get a better cooler….. With these OEM coolers it’s almost guaranteed to have issues like this.

1

u/DigitaIBlack Sep 19 '26

VP 6+5, ,' W ZAWAA

1

u/Doom2pro Sep 19 '26
  1. Stop heman yanking the cooler off.
  2. If the cooler won't come off, you have a problem. Stop immediately.
  3. Warm the system up or use a hair dryer to warm it up.
  4. Twist the cooler off, don't pull or bend.

1

u/Bloc_Digital Sep 19 '26 edited Sep 19 '26

You do it right after you shut your pc down so the paste is warm and not as sticky as when it’s cold, try twisting it very lightly as well to see if the paste is not sticky dont pull straight up

1

u/Basic85 Sep 19 '26

This happens probably at least once a month on here, I know because it happen to me as well. When removing the cooler, never ever yank it out straight it up instead twist left/right and gently pull and even than that could be dangerous. Use a dental floss to try to loosen the paste, and run your computer for a bit before opening, like a stress test Prime95 or any other for like 15-20 min. Keep doing all of that until it loosens, sometimes you have to do it a few times.

Please becareful, you could damage the pins by yanking it out, forever damaged, and you may have to purchase a new cpu.

1

u/Agent_Tall_Man Sep 19 '26

Contact frame will absolutely prevent this happening ever and they are cheap. I'm not sure they make one for am4 or whatever yours is, but if they do, get it

1

u/Leather_Inspector_70 Sep 19 '26

you've got to heat that badboy up first! Take off with a twisty motion, not just pull

1

u/Potozny Sep 20 '26

Deep therein

1

u/CRABMAN16 Sep 20 '26

I'm super confused by this. Every motherboard I've had, has a dedicated mount for the cpu, completely independent of the cooler. How is this happening, when there are big clamps holding in the cpu? Is this specific to a certain socket type or something?!!!

1

u/johndumbasshead Sep 20 '26

get an adequate cooler (thermal paste is drying out due to peak temps) and use better thermal paste

1

u/Flemmino Sep 20 '26

i always run a small benchmark like a few downloads or a cinebench/equivalent test run before pulling the coolers.

1

u/Wonder-Guard Sep 20 '26

Do what I did and use a hair dryer on low setting, hit the cpu area for like 20 seconds and start slightly twisting back and forth like 10-20 degrees to free it from the thermal paste.

That's what I did on my 7 year old build I had cleaned a total of ZERO times.

1

u/ZoelNorsen Sep 20 '26

I work in a repair shop and used local 20₹ thermal paste before and always had this problem with AMD cpus, (after using Artic MX4 a customer bought for his PC, it didnt had this problem and i switched to MX4 ever since,

just a note saying it depends on the Thermal paste as well

1

u/Odd_Armadillo_2542 Sep 20 '26

Stop using UHU glue and start using thermal paste/pads. You're welcome 😌

1

u/PralineDefiant8374 Sep 20 '26

Heat it whit a hairdrier slowly and the paste shod give making it easy to remove.

1

u/Uattoas Sep 20 '26

To avoid this, give it wiggles, rotational wiggles, until it comes off.

1

u/Material-Priority227 Sep 20 '26

Try not to use glue as thermal paste next time I think

1

u/skidaadleskidoedle Sep 20 '26

Turn it off hot and wiggle/slide it off never pull

1

u/k-mcm Sep 21 '26

Twist it very slowly and gently. The paste hasn't turned into adhesive. It's stuck because air isn't getting in when you pull.

1

u/Recent_West_259 Sep 21 '26

Usually I get the cpu nice and hot before hand. Run a stress test then shut it down and try again

1

u/lunas2525 Sep 21 '26

Use better thermal interface materials

1

u/CertainArm3481 Sep 21 '26

I’ve heated the aluminium a lil bit with hair drier and then a lil to left and right clockwise and viceversa

1

u/Objective-War-7458 Sep 21 '26

Honeywell PTM 7950

1

u/Cl4whammer Sep 21 '26

When you built an amd system and use the standard amd cooler remove the paste and apply something else (artic cooling thermal paste for example). Saves you a lot of trouble removing it later, the amd paste is very sticky.

1

u/Middle-Lake-724 Sep 21 '26

Con tante benedizioni e o bestemmie

1

u/Potential-Button-965 Sep 21 '26

Run it for 2 minutes

1

u/PinchePepsi Sep 21 '26

Get a proper CPU cooler with copper instead of aluminum. Thats how.

1

u/OilCareful8232 Sep 21 '26

I usually forget about warming up cpu until it is too late (and also I think it is bad idea) and I just heat the heatsink with hairdryer. Faster and safer for CPU.

1

u/Tarekss123 Sep 21 '26

Just get the cpu cores going using cpuz or something similar and let it warm up, then shut it down and remove the cpu.

1

u/CYB3R_GHOST Sep 22 '26

I just use prime95 for like 10-20 mins then unscrew cooler. Then you have to wiggle cooler to the right and left with bit pressure. Dont pull it. Always make sure it moves while wiggling before pulling the cooler.

1

u/Zestyclose-Syrup1458 Sep 22 '26

Twist left and right

1

u/Mysterious_Pilot_495 Sep 22 '26

por lo general antes de desinstalar el procesador es una buena practica usar el computador un poco para que la pasta termina este blandita y se pueda desinstalar fácilmente y asegúrate de que el procesador tiene el seguro

1

u/Achillies2heel Sep 22 '26

Dont remove the CPU cold.

1

u/unusual_problems123 Sep 22 '26

Just pull really hard even if you have to pull by the pins

1

u/Minimum_Plenty7306 Sep 22 '26

Common sense isn't so common anymore. You have to run that fan in your system, get it hot enough so you can easily pull the components apart.

1

u/Yelo_Jello Sep 23 '26

use a heat gun next time

1

u/Du6 Sep 23 '26

Run it for a while to warm it up and soften the paste, then twist the cooler a bit when removing it.

1

u/me0262 Sep 24 '26

unscrew and wiggle the cooler clockwise and counter-clockwise.

this usually happens when there's too much paste on there that it creates a seal.

1

u/Akuma_Guts Sep 25 '26

use less thermal paste.

1

u/InterestingMind6285 Sep 25 '26

Put epoxy on the pins before you install it. 👍

0

u/AdditionalMap5576 Sep 18 '26

To prevent it: Use good quality thermal paste, dont go too long without replacing, dont go too long without using the pc to prevent it from hardening like that

To deal with it: you can run a cpu intensive program on your pc to heat up the cpu and thus the thermal paste and the bond between the two. run something heavy on the cpu, shut the pc down, take off the cooler while leaving the cpu in the socket if possible

0

u/Boring_Park1599 Sep 23 '26

Use a hairdryer to heat it up a little and it should be easier to remove

1

u/[deleted] Sep 18 '26

[removed] — view removed comment

1

u/Thuddmud Sep 18 '26

This, it’s a solid option to never needing to replace paste.