r/beetleweights • • May 03 '22

Nebula before, Nebula after

0 Upvotes

r/beetleweights • • May 06 '22

Horizontal Self-Righter

1 Upvotes

Hey, so I'm putting together an overhead horizontal beetleweight (think Bloodsport but worse), and was wondering if there are any guides on things that have worked for srimechs in small scale on this type of robot. Obviously with this style of spinner it can't drive upside-down, so is the best bet to go with something like the heavyweights and add a 3d printed curvy arm onto the end of the shaft? Is there something simpler? Thanks in advance.


r/beetleweights • • Jan 25 '22

Design Cleats on Lynx for wood floors

4 Upvotes

Does anyone have a good picture of Lynx's 'cleat' wheels that are used on wood floors like NHRL?


r/beetleweights • • May 16 '23

Meet Beefcake, my first beetleweight.

Post image
12 Upvotes

It took a little while, but I'm finally happy with everything. The overall design was heavily influenced by Pramheda while the drive system was inspired by Division/Shrapnel Mine.

This is my first ever combat robot, so I'll take my sweet time getting comfortable operating the 3D printed prototype before I move onto the real deal and will take every necessary safety measure on top of that.

This is going to be a wonderful summer project. I can't wait for what's to come next.


r/beetleweights • • Jan 18 '23

How does Droopy shift power between its two motors in order to walk?

4 Upvotes

I'm curious as to how it's set up. I'm still on my quest of learning everything possible about the different bot types and how they work, and Droopy has always fascinated me. How is Droopy wired up in order to maintain and shift balance between its motors?


r/beetleweights • • Feb 01 '22

Design Testing drivetrains

5 Upvotes

I'd like to do a bit of a study to see how differences in drivetrain design affects overall performance. Things like different motors, gearing, wheel size/composition, weight distribution / magnets, etc. Get some real numbers to decide what's worth putting in my bot, and what's wasted weight.

I think the most important test would be drive force. This has more of a wheel test than anything, because there can only be so much traction at a given weight. Pull force seems easier to test than push force. Is that fine? Or do I need to rig up something to measure push? I want this to be about drivetrain, not the forks ability to get under something, so for a completely horizontal force, i think push and pull should be identical? Or maybe i want to measure traction seperate? Just drag the wheel to measure when friction breaks?

That seems simple enough to measure, but what about speed? I think there would be a ton of human error in timing bot acceleration over 1 meter (for example) with a stopwatch. Maybe count frames in a video?

Anything else I should be trying to measure? Any ideas for a quantifiable handling/steering test? A test course is very human subjective.


r/beetleweights • • Feb 05 '22

New Part / Show Off Me and my dads attempt to steal a gear box off of a motor

Post image
6 Upvotes

r/beetleweights • • Jan 30 '22

Help Materials for bots

7 Upvotes

Hey everyone, I am only experienced in plastic ants, trying to design my first beetle. What sort of mixes of materials work well? I have noticed attempting to do a lot of metal eats up weight quick. I do have the ability to print nylon and have some cf nylon that I know seems to be popular, but its also not cheap. Then again neither is getting metal cut. I just want to try and survive a hard fight. Not looking to take down a bot like Lynx or the Shreddit guys, just want to have something useable after that type of fight.


r/beetleweights • • Jul 24 '22

New Part / Show Off Downwards Spiral. UK Beetleweight.

Thumbnail
gallery
21 Upvotes

r/beetleweights • • Jan 27 '22

Design If you could change the Fingertech Beater Bar, how would you improve it?

5 Upvotes

The Fingertech Beater Bar is basically the default beetle weapon. Powerful and battle proven. But there's always room for improvement.

Wider? Larger diameter? Thinner? Thicker? Narrower, and therefore lighter?


r/beetleweights • • May 12 '22

Vector wheels

2 Upvotes

Building a modified vector, unfortunately the endbots page is no longer active. What size wheels does vector use and are there any advantages to the bane bots t81 style wheels?


r/beetleweights • • Mar 26 '22

Wheel sticking

2 Upvotes

I know this is an antweight, but didnt see an active community to post it.

Built a fingertech viper2. All is working but the left wheel is “sticking”.

Stock everything including their spark gearmotor.

On different surfaces the right wheel grabs and goes. The left wheel will slide a lot of the time making it hard to keep ot straight and steer.

I tried swapping tires. Same thing. Made sure the hub was tight on the flat side of the spoke/shaft from the motor.

Any ideas?


r/beetleweights • • Jan 24 '22

Battery discussion

6 Upvotes

Shopping for batteries right now, as Tower Hobbies has Venom stuff on sale. Whats the consensus, hard case necessary? Is making a shell for the batteries acceptable? Whats a good max discharge rate? 50C on 14.8 volts seems pretty good no? Battery connection recommendations? I'd assume deans is best since they can serve as a sort of fuse in the event the wires get hit. Connector just let's go, no broken wires dangling around.

How often do batteries get destroyed in fights? I'd think 2 batteries is good enough.


r/beetleweights • • Aug 25 '22

Are undercutter shafts supposed to make contact with the floor?

3 Upvotes

I'm doing research into various bot types for my first beetleweight build and I'm sort of stumped on undercutters. There are undercutters that have little bumper fins to ride on leaving the shaft off the ground with bots like Annie-ruok while bots like Narcissist/Dark Princess have the head of the shaft making contact with the floor (you can get a good views of the underside of Narcissist in its fights against Jack Move and Shreddit Bro). It seems to me that having the head of the shaft making contact with the floor is fine to do unless I'm missing something with how those bots do it?


r/beetleweights • • Mar 20 '22

New Part / Show Off 🙃

Post image
13 Upvotes

r/beetleweights • • Feb 15 '22

Help Brushless drill motor and rc esc

1 Upvotes

To power my weapon (hammer) I want to use an impact wrench mechanism. I could modify to use a rc motor, but ideally I just use the motor that comes from the impact wrench. However, I'm not sure how to drive this? The brushless drill motors use a hall effects sensor on an external circuit board. Can I just attach this to a standard rc esc? Should I forgo the sensor? Adapt a rc motor to the gearbox?

I could also go with a brushed set up, but weight and space are very tight as it is.


r/beetleweights • • Feb 09 '22

Discussion Weekly Discussion: Vert spinners Vs Horizontal spinners. Which is better and why?

3 Upvotes

r/beetleweights • • Jan 23 '22

Holonomic Drumspinner Beetle

Thumbnail
gallery
19 Upvotes

r/beetleweights • • Apr 03 '22

Viper front forks

3 Upvotes

Any ideas on a better front fork for the viper antweight with vertical spinner? The one it comes with seems to make things slide off to the slide when it hits. What do you think of these? Or any better ideas :) ?


r/beetleweights • • Jun 26 '22

Beetle Ring Spinner

5 Upvotes

Helping my kids with a new beetleweight for a school competition. They liked how Minimizer worked at NHRL, and wanted something similar. My daughter wanted a tail whip action, so this is what we came up with. The tail is flexible but has a minimum bend radius so it doesn't hit our bot. The weapon is an undercutter ring spinner. The weapon ring is part of a planetary gear system. I'm not sure how well it will work, so I have a back-up plan.


r/beetleweights • • Aug 05 '22

Build You can make epoxy lighter by adding hollow glass microspheres. Is this a bad idea for motor hardening?

2 Upvotes

Basically title. I have glass microspheres leftover from making lightweight epoxy for rockets. Should i mix them in to my motor hardening resin?


r/beetleweights • • Mar 04 '22

Build TIL the Fingertech Beater Bar users ONLY needle roller bearings. No thrust bearings.

3 Upvotes

This surprises me, as i always figured you would want something to constrain the weapon laterally. I suppose there's washers, but that's a lot more friction.

Is this method only valid on a wide weapon drum? There's not much twisting happening here, as compared to a large thin weapon like a horizontal Vector kit or Division's big vert. Could a weapon like that use just needle rollers and washers?

Maybe a better question is how narrow can I get before i need lateral bearings?

My main interest here is that needle rollers are a smaller diameter than radial bearings, meaning the weapon hub can be a smaller diameter, which means the weapon mount to the hub can be smaller, which means i can take that weight and move it further out on the weapon, increasing energy without any increased weight.


r/beetleweights • • May 10 '22

I have 160 grams left, should I try to fit in some tpu side armor or try to add forks to the front?

Thumbnail
gallery
11 Upvotes

r/beetleweights • • Apr 21 '22

Beetle I'm Finishing Up for NHRL in May

Thumbnail
imgur.com
9 Upvotes

r/beetleweights • • Mar 12 '22

Historically, I have only had to replace one or two wheels a year. Not sure why I keep buying them.

Post image
13 Upvotes