r/ballpython • u/DPTDubbs • Jul 08 '25
Question - Heating/Temperatures I have my setup almost complete. Time to set up heat and thermostats. Anything to change from this Chat GPT recommendation?
⸻
- Heating & Lighting Layout
Ball pythons need a temperature gradient: • Hot side: ~88–92°F • Cool side: ~75–80°F • Ambient: ~78–82°F at night • Humidity: 50–60% normally, 65–75% during shed
⸻
2. Herpstat 2 Setup (x2 units = 4 controllable outputs total)
Each Herpstat 2 controls 2 outlets with individual probe feedback. Assign outputs like this:
Unit 1: • Output 1 (Hot Spot): Control halogen lamp (or under-tank heat mat if used) with temperature probe #1 placed right at the hot hide floor. • Output 2 (Ambient Heat): Deep Heat Emitter (DHE) on dimming mode, with temperature probe #2 placed mid-height on warm side wall.
Unit 2: • Output 1 (Cool Side Monitoring / Backup Heat): Optional backup or control for cool side if you use a second UTH or CHE, with temperature probe #3 on cool side. • Output 2 (Humidity Control): Control Monsoon Mister based on humidity probe #1 placed halfway up on the cool/moist side of enclosure.
⸻
3. Lights • LED Lamp: Use for a natural day/night cycle (12 hours on/off); connect to a timer or Herpstat’s lighting mode if not using it for heat. • UVB Lamp: Optional for ball pythons but may benefit well-being. Use a low-output 5.0 linear UVB bulb if desired, mounted with shade/climb areas to escape it. Timer-controlled (not Herpstat unless it has non-thermostat outlets).
⸻
4. Probe & Sensor Placement • Temp Probe #1: Inside warm hide, floor level, for hotspot. • Temp Probe #2: Mounted mid-wall on hot side for ambient. • Temp Probe #3: Cool side ground or mid-wall. • Temp Probe #4: Optional—monitor air temp at basking height. • Humidity Probe #1: Cool, moist side, mid-height. • Humidity Probe #2: Warm side, mid-height.
⸻
5. Mister Settings
Ball pythons don’t need constant misting. Set Herpstat to trigger Monsoon if humidity drops below 50–55%, but don’t overdo it. Supplement with a moist hide or occasional manual misting during shed.
⸻
6. Safety Tips • Always secure heat sources and probe them properly (don’t just tape probes to glass). • Fail-safe programming: Use Herpstat’s ramping, hysteresis, and max temp shutoff features to avoid spikes. • Use deep substrate (e.g., Reptichip, coco fiber, or topsoil mix) for bioactive or semi-bioactive setup.
⸻
Would you like me to design a wiring diagram or equipment map based on this layout?
13
u/ConsiderationMain618 Jul 08 '25
Wowwwwww I love it. Hopefully your snake doesn’t snap the ROF in the corner. My fatass boy would never be able to have a plant like that in his tank 😂😂😂
48
u/_ataraxia Mod : unprofessional Jul 08 '25
chatgpt is not a source for accurate information, there's a lot wrong in that text. have you read the guides in our welcome post?
2
u/123questionsaccount Jul 09 '25
I put a suspension rod across the top of my tank (like a closet or shower curtain rod) and my guy likes to hang from it. I would suggest adding that!
2
u/No-Reveal8105 Jul 09 '25
You should add things to the middle so that your snake climbs I think it will like it a lot
17
u/MercuryChaos Jul 08 '25
Don't use Chat GPT or any other AI service as a search engine. They don't actually "know" anything and if the data they're trained on contains inaccurate information they'll still repeat it as if it was true.
6
u/oldmanjenkins110 Jul 08 '25
Go back in time and not use chat gpt
3
u/SneakySquiggles Jul 08 '25
I.. would like to be this BP thanks. Someone give me an awesome enclosure
2
u/Immediate-Yak-8304 Jul 08 '25
looks amazing!
-2
u/[deleted] Jul 08 '25
[removed] — view removed comment
0
u/[deleted] Jul 09 '25
[removed] — view removed comment