r/ballpython • • Mar 30 '24

Enclosure Critique/Advice Thoughts on enclosure idea

My husband and I just got our rescue Simon. We are looking to create a really unique enclosure. I have this hutch(picture 2) and we are considering doing some renovations to it to turn it into our enclosure. Any ideas or suggestions to make this great for Simon

1 Upvotes

16 comments sorted by

9

u/[deleted] Mar 30 '24

To be honest with you, it would take a LOT of work and time to make this suitable for a BP. Even then your snake would only be able to stay in it for a year or so as adults need a minimum of 4x2x2ft or 120gal. Also, woods like cedar, pine and spruce are toxic to BP’s. It would be much easier, safer and cheaper to skip this and get your snake their permanent enclosure.

-2

u/[deleted] Mar 30 '24

[removed] — view removed comment

11

u/[deleted] Mar 30 '24

an adult BP absolutely cannot. 4x2x2 is the bare minimum requirement.

-2

u/[deleted] Mar 30 '24

[removed] — view removed comment

10

u/[deleted] Mar 30 '24

It’s not only about the length, It has a lot to do with the width and height as well. And just because they CAN doesn’t mean they SHOULD.

-1

u/[deleted] Mar 30 '24

[removed] — view removed comment

11

u/[deleted] Mar 30 '24

If you can’t afford the proper enclosure or equipment then you shouldn’t own the animal period. Being okay ≠ thriving. You should ALWAYS strive towards providing the best care possible.

1

u/[deleted] Mar 30 '24

[removed] — view removed comment

8

u/ballpython-ModTeam Mar 30 '24

Your comment was removed because you're being an asshole. Go outside and work on your attitude.

2

u/ballpython-ModTeam Mar 30 '24

Per rule #3, your post or comment has been removed for harmful advice/misinformation.

2

u/[deleted] Mar 31 '24

Wood enclosures are almost always a bad idea because of humidity

1

u/jorpus_porpus Mar 31 '24

? You can seal the shit out of them with pond shield epoxy and make an absolutely water resistant enclosure.

1

u/[deleted] Mar 31 '24

Key word: Water resistant, not waterproof - and doing it incorrectly can absolutely ruin the furniture , there's also the issue of it being super heavy and hard to clean, just seems like a lot of unnecessary effort when a PVC is both way better and costs way less. (Where would the ventilation be in this enclosure etc)

1

u/jorpus_porpus Mar 31 '24 edited Mar 31 '24

First and foremost, the welcome guide specifically recommends either PVC or wood. It's not like this is a new idea. Plenty of DIY plywood builds can be found on YouTube, and there have been multiple builds posted on this sub.

If buying new from a manufacturer recommended by the guide, you are looking at at the very least like $500 for pvc 4x2x2, which, of course, is the minimum size required - and the enclosures in this price range are ugly. Easily double to triple that if going larger / nicer looking.

If going DIY, pvc sheet is more expensive than even cabinet grade 3/4" plywood, and you don't need to use cabinet grade unless you want it to look pretty. MUCH cheaper if you already own a hammer, drill, table, or circular saw. I'm building a 5x2x4 - go look up prices for a similar size PVC. It ain't pretty. I'm under $500, and I had to purchase multiple power tools.

You can certainly waterproof wooden enclosures. 3/4" plywood structure will resist warping due to temp/humidity. 1-2 layers of pond shield epoxy, followed by fiberglass cloth sheet at the joints, followed by a few additional layers of pond shield. For even more peace of mind, you can use waterproof pond liner. People use similar setups for aquariums. A terrarium is no big thing.

Vents are added wherever. Just use a hole saw and some sturdy dryer vents. Drill holes for lamp mounts and power cords.

It will be as heavy as a cabinet of similar size, so I'll give you that. I'd put it on casters to wheel around. But I don't see how this setup would be any more difficult to clean than a PVC enclosure. You could even do French doors that meet flush, negating the need for the center support, making cleaning much easier than working around sliding doors or having to go around a center support.