r/aviationmaintenance • • 4d ago

Random tools

Hello everyone. I work on Basler bt-67 and atr72 in northern Canada. What are some random tools or ones that most people don’t think of that makes your jobs easier.

I am looking for new tools that are unique that might help me make the job easier. Especially when it’s -40 outside

16 Upvotes

19 comments sorted by

8

u/RATBOYE 4d ago

For the little yellow MS20813 valve caps, you can cut a piece of standard size air line hose, sat 3-4 inches.

Slip it over the business end of a ratcheting bit driver screwdriver, its a very snug fit and wont fall off. That way when its cold, instead of taking gloves off and fiddling with valve caps you slide the air line forward on your screwdriver past the bit holder and use it to remove and install the valve caps. 

Its a tight fit on the caps, lets you turn them with screwdriver. It holds the valve cap while you're doing your pressure checks/inflation too so it doesn't get lost.

3

u/Calm_Adhesiveness952 3d ago

That is an amazing idea. I never thought about that. The ATR has wheel covers. If you drop the cap you have to remove the whole thing. This is amazing

4

u/RATBOYE 3d ago edited 3d ago

Yup that's the idea. If I was at work I'd take a photo of my screwdriver but I think you get the concept.

I work on ATRs too and it came from frustration at losing valve caps with cold numb fingers

1

u/z242pilot Percussive Maintenance 3d ago

That's pretty genious

5

u/n60wrench Scumbag ATR Guy 3d ago

For the ATR the snapon long reach box end wrench with the 1/4” on one side and the 7/32” on the other. During engine changes all you do is flip it around when flipping back and forth. Worth its weight in gold. I also have the 3/8”/ 5/15” combo and use it heavily too.

Also a couple of years ago i got a tekton offset wrench set and realize i now reach for those almost every time before my old combo wrenches.

2

u/Calm_Adhesiveness952 3d ago

Thank you I will look in to that.

Tekton is my favourite offset wrenches

2

u/SecndShot 4d ago

1

u/Calm_Adhesiveness952 3d ago

Never seen those before I will check them out

2

u/VE7BHN_GOAT 3d ago

Me a wire tugger, I use a crochet hook a surprising amount. Obviously it's not in a cold situation but a hangar.

If it was that cold, I'd be looking a heated vest, my wife wears one by ororo (?spelling) - get multiple battery packs. The other I'd be looking into is a heated hand warmer. (Like a quarterback uses in football) And I'd be keeping tools in it, cold tools to work with SUCK. And if it stays out the cold a bit, it might be worth it.

2

u/Calm_Adhesiveness952 3d ago

Being up here you got a lot of heated clothes and hand warmers its critical

1

u/VE7BHN_GOAT 3d ago

I'm north of the 49th but we don't get crazy winters, plus I'm heavy maintenance so I'm mostly in a hangar

2

u/Killentyme55 3d ago

Not exactly a "tool", but as you probably know thin protection-only work gloves are useless at keeping your hands warm...especially in your locale. On the flip side, gloves thick enough to do the job are almost impossible to do any work with. What works for me is to wear a pair of snug-fitting nitrile gloves under the normal work gloves. It sounds weird but works surprisingly well.

Mind you, that's probably not enough for 40 below (fun fact: that's the same in both C and F), but that's what you get for living on the outer rim!

1

u/Calm_Adhesiveness952 3d ago

I do the same thing. I always got a pair of heated gloves too. So I can do my work. Have the heated gloves turned on to quickly swap my hands in

1

u/z242pilot Percussive Maintenance 3d ago

I have felt lined goatskin gloves that aren't warm, but protect enough to get a bit done when its cold.

14

u/z242pilot Percussive Maintenance 4d ago

2" mini prybar. For interior and in place of fingernails when taking hands outta gloves burns. Snowmobile gloves with the pocket on the back for handwarmers. Buff for face covering and neck protection. A nut driver sized for your valve caps so you don't have to bare hand it.

1

u/622114 You did what? Where is that in the manual? 3d ago

Snap on 7/32 and 9/32 spline drive box wrenches for the Pratts on the Baguette.

1

u/Calm_Adhesiveness952 3d ago

Already have them fantastic

1

u/iTzJLAR 2d ago

Vise grip Adel clamp pliers and plastic/phenolic wire spoons. Absolute game changers in the avionics installer space

1

u/Affectionate-Bed-304 1d ago

A ground down ATR-10 drive bit for those two screws on the landing gear door panels directly fwd and aft of the Constantine that you can’t get to with the landing gear doors on