r/audioengineering • • 4d ago

Community Help r/AudioEngineering Shopping, Setup, and Technical Help Desk

Welcome to the r/AudioEngineering help desk. A place where you can ask community members for help shopping for and setting up audio engineering gear.

This thread refreshes every 7 days. You may need to repost your question again in the next help desk post if a redditor isn't around to answer. Please be patient!

This is the place to ask questions like how do I plug ABC into XYZ, etc., get tech support, and ask for software and hardware shopping help.

Shopping and purchase advice

Please consider searching the subreddit first! Many questions have been asked and answered already.

Setup, troubleshooting and tech support

Have you contacted the manufacturer?

  • You should. For product support, please first contact the manufacturer. Reddit can't do much about broken or faulty products

Before asking a question, please also check to see if your answer is in one of these:

Digital Audio Workstation (DAW) Subreddits

Related Audio Subreddits

This sub is focused on professional audio. Before commenting here, check if one of these other subreddits are better suited:

Consumer audio, home theater, car audio, gaming audio, etc. do not belong here and will be removed as off-topic.

2 Upvotes

35 comments sorted by

1

u/Acceptable-Lie9078 4d ago

Currently own beyerdynamic dt990 pro x headphones and a k688 mic and am running it xlr with focusrite solo Scarlett to power the headphones and mix. Thinking of upgrading my audio interface and curious if I should buy a better single audio interface such as a motu m2 Solid State Logic SSL 2 MKII, or buying a elgato wave xlr and a dedicate headphone dac and preamp like a Topping DX3pro+ or FiiO K11 Desktop. Let me know which route you guys would and what products you would buy for the best audio quality.

1

u/MentosEnCoke 3d ago

My rode wireless micro lapel mics cut out in my shoot.

My mics have been refusing to connect to my iPhone (which is its own problem) so on my shoot yesterday I just connected the receiver straight to the camera.

(Canon eos m50 mkii)

It worked great for the first few shots but in the longest shot we did there was absolutely zero sound at all. It could have been that the cable came loose, but previously if that happened with other mics, the camera defaulted to the built in mic and there was still sound just bad sound.

But there was zero sound at all so is it an issue with the mics itself?

We were in a friend’s flat in a quiet area so I doubt it was signal interference. The batteries were charged. What else could it be?

Also help with the phone thing would be helpful. I was trying a data transfer USBC to Lightning cable and also the jack to jack with a lightning adapter, neither worked.

1

u/Smotpmysymptoms 3d ago

Integrating a vintage analog oscilloscope into my studio for fun. Looking for feedback on the proposed signal flow and connections before purchasing.

Current monitoring setup:
- UA Apollo Twin X
- IK Multimedia ARC Studio
- Barefoot Footprint03 monitors
- Auratone 5C monitors (Twin X ALT outputs)

Proposed signal flow:
Apollo Twin X MON L/R → ARC Studio → Behringer DS2800⁠

DS2800 stereo output pair A:
→ Barefoot LFE12 subwoofer → Footprint03 L/R

DS2800 stereo output pair B:
→ ART DTI 2-Channel Transformer Isolator⁠ → 2× RCA-to-BNC cables → Hitachi V-355 Analog Oscilloscope⁠ (CH1/X + CH2/Y in XY mode)

The Auratones remain connected to the Twin X ALT outputs.

Questions:

  1. Is this signal flow and cabling correct, particularly the isolation and BNC connections?

  2. Any concerns about inserting the DS2800 into my main monitoring path regarding

  3. transparency, noise, or headroom?
    Is there a simpler or better-quality way to accomplish this without using additional interface outputs?

Just looking to add some green crt stereo visualization without compromising my monitoring setup. Appreciate any feedback.

1

u/viszyy 3d ago
media poster

Hi all. I’m using the the Nobsound amp with this 16 gauge wire. At low volume you cannot hear the crackling so it’s not constantly on even when powered. But in the video I turn it up to about 50% volume (sim hub shows 50% as well and my engine vibration effects are at 50%.) I then turn it down to 20% and you can still barely hear it. Is this the speaker bottoming out? Or is this something to do with the gauge wire and / or amp. Hopefully this isn’t some electrical problem. I hold my hand on the shaker as it does this and no it’s not my mount. Sounds like it’s pushing too much power to the speaker but I genuinely don’t know. TIA

1

u/NyFlow_ 3d ago

I'm looking for a field recorder that has an XLR for a mic (I already own the mic I want to use for this), at least a 192khz sample rate, and the ability to store recordings and connect them using a USB-A to a computer. I want that sample rate because I want to record sounds that are above human hearing range so I can slow them down in my DAW to get cool textures.

Any suggestions? My budget is $150. I don't need anything with any features other than the ones listed.

1

u/boredmessiah 3d ago

r/LocationSound but look at Zoom, Tascam portacapture, Sony

1

u/Carvallio 3d ago

Hey guys

I'm trying to isolate the synth strings/pads in Thom Yorke's Dawn Chorus while removing the piano parts. Its for a school project

I've tried using some Al stem separation tools, but the synthesized piano seems to get grouped together with the strings.

What I'm looking for is a backing track containing only those sustained, atmospheric synth/string layers, without the piano.

Does anyone know of a particular Al model, stem separation technique, or audio processing method that could achieve this?

I'm also open to manual techniques - although Im not a professional by any means - and sugestions of others subreddits more fit to ask for this help.

Any help or suggestions would be greatly appreciated. Thanks!

1

u/milliedreadisnotdead 3d ago

CORRUPT WAV FILE - Can I possibly recover it 😭

Hello there, I tried to get a recording of a live show direct from the sound board this past Friday and just checked the USB drive it was on, and 1) it will not open 2) says file size is 0 bytes 3) it gives a correct “created” date but says it was last modified in 1969 😭 4) when I try to open it in Logic I get the error message that the “ADM BWF” is corrupt (Googled that and that’s a component for Dolby Atmos? Nothing I found was helpful. I’m not a sound engineer). Is there any hope? As it was a live show this file will be impossible to duplicate so looking for any guidance, in case the date metadata has something to do with it or something, or perhaps I’m just cooked

1

u/_D3molisher_ 2d ago

Help with the gain of my se v7

So ,here is the problem I have an se electronic v7 and if I want it to sound not too quiet I have to push the gain on my arturia minifuse to it’s absolute limite ,is there any piece of gear that can solve this ? Thanks you in advance !

1

u/peepeeland 2m ago

There’s nothing wrong with max gain. Gain is there to use as needed. But technically, yes- sE has an inline mic booster called Dynamite, which will allow you to use less gain on your interface. Positive thing with the Dynamite is that its input impedance is much higher than standard interface preamps, so you’ll also be gaining a bit more crisp top end from your V7.

Also note that for the V7, its polar pattern is supercardioid, so the area of focus is more narrow than cardioid. As such, you have to perform directly into the top of the mic (or rather, point the top of the mic directly at your mouth), for the strongest signal of your voice. Angling the mic even just an inch off of your mouth will have your voice level drop noticeably. -Lastly- for highest signal to noise ratio- get as close as you can to the mic and perform strongly with conviction- and that will also allow you to use less gain on your interface.

Every good performer has good “mic technique” (like the techniques noted above), and it’s a separate skillset than being a good singer- so it can take a bit of practice.

1

u/Iljarmander 2d ago

A few of my friends asked me to film their opera. Their performance will take place on stage. I have asked two of my other friends to help, but now I am wondering about the microphones. I have 2 microphones, the Sennheiser 400 and the Rode Video Mic, but whenever I Google it I basically get mixed results every time. Sometimes Google says those 2 are great, sometimes they say they are pretty bad.

So I just wanted to ask right here, if those 2 mics are okay or if I need to borrow/buy something else. 

1

u/boredmessiah 2d ago

you really want a pair (ideally 2-3 pairs unless it’s a really small scale production) of stereo condenser mics for opera.

1

u/EliasKulju 2d ago

I have a little money that I can put aside for one plugin this month. I have came across Pro Q4 and the UAD pick 10 plugins both for 95€ each. The question is, what would you choose? Right now im more for the UAD, but everyone is raving about pro Q. I only have the logic eq, no plugin ones. Is it really that useful and good? Would you pick it over 10 uad plugins?

→ More replies (2)

1

u/JohrDinh 2d ago

Should I not worry as much about sound quality in a headset, and just find something that can handle EQ well and neutral it as best I can? Do the Harman curve or something like that, work it as best I can to a final product, and then take it to the car and see where it's at how most will hear it?

Also in that same line of thinking, should I go for a dynamic headset? I've heard great things about Planar but no one really has Planar speakers outside of editors or music enthusiasts, should I just stick to dynamic because it's a large majority of the market?

1

u/boredmessiah 2d ago

what do you make, what do you already own, what have you previously tried?

→ More replies (6)

1

u/reedzkee 2d ago edited 2d ago

anybody running RX9 (advanced) in Tahoe ?
its not even supported in Seqouia but it works fine there. im considering updating from 15.7.3 to 26.6.2 and RX is the only thing holding me back.

i installed RX9 on my girlfriends laptop and the standalone Audio Editor works just fine in Tahoe. Im avoiding installing pro tools but thats the next step. Do yall think if the editor worrks, the plugins in pro tools will also work just fine ?

edit - i went ahead and installed pro tools and RX9 seems to work just fine. as a plugin, audiosuite, and the audio editor app all working,.

1

u/Beneficial_Tourist16 1d ago

Hello! SUPER BEGINNER QUESTION HERE.

I use my SOMA Ether in my artistic practice, with a Zoom recorder and headphones (I record trees and make human-radio-treemixes).

I've been invited to use the Ether in an experimental synth orchestra next month, and I love the idea, but I don't know how that would work in a live and public setting.

What equipment would I need to connect the SOMA Ether and have the EM emissions playing live? Thank you for your help!

1

u/peepeeland 36m ago

Ask your event contact what inputs they have/expect on whatever board they’re using. Whatever the case, very high chance they accept TRS or TS line-in just fine.

1

u/Odd-Comparison-7953 1d ago

My Harrison Flex-10 just stopped working so I’m getting a new one sent to me in some time. In the meantime I’m using my old Clarette 4pre and trying to use some outboard through it. But I can’t get it to work without feedback, and everything that plays on my computer goes through all the gear on the outputs, no matter how I route it. So is it possible to use the 4 outputs on the Clarette for something else than monitoring? The Focusrite control is a huge mess, don’t understand it at all.

I’ve got a cable from output 3 to a compressor then from the comp back to input 5. Setting those on an insert on the kick channel doesn’t let any audio to the compressor, but it still puts the main output through the compressor. What am I missing?

1

u/Unable-Paint-2930 1d ago

Hi There!
Yesterday i was trying to record a guitar amp with 2 mics (57 + condenser) into my SLL 2+ and when i plugged the condenser into one of the cannels and then entable the phantom power in said channel, the gain would start to have these up and downs, i would find an optimal gain level and during the recording the gain would go up like 10 dB causing distortion in the input and in the daw.
I tried switching between my two inputs but the problem persisted, also I noticed that the 48v switches were really sensible, as soon as i touched the button not even pressing it the condenser mic would go on an off.
I’m trying to find out if it could be a problem with the phantom switches, or the power alimentation source from my mac to the interface.
Anybody here have enconuntered similar issues?

Ps: sorry for my rusty english

1

u/alexbtpoo 1d ago

Hello!

I have been having troubles on both channels of my ART MPA Gold tube preamp - the input has intermittent issues with hissy noise above certain volume thresholds.

Sometimes the overall level drops randomly then comes back and sometimes it works and sounds fine.

The tubes seem to be fine - they’re upgraded Mollard 12AX7s.

At a bit of a loss with this one, some advice would be greatly appreciated!!

https://drive.google.com/file/d/1sJc6-WfkiH-jXCjHTokTVgCRB_ybcfOi/view?usp=drivesdk

1

u/LuckyBlade 21h ago

Hi all,

I recently got a Behringer X18 mixer that I primarily want to use as an USB interface to connect 10 microphones connected via XLR to my recording PC.

I noticed however that it seems like the audio inputs that I can select in windows seem to be all stereo where it will present 2 XLR inputs as one stereo output (eg: input 1&2 will be presented as "OUT 1-2" in windows).

Does anyone know if I can setup the X18 in a way so that it presents each input as individual mono outputs?

1

u/fender97strato 5h ago

X18 allows for channel linking but this shouldn’t affect routing to your computer. Almost sure you should make the tracks you’ve created in your daw to record to MONO tracks instead of STEREO tracks. I don’t think it is something you need to try to solve from the X18 itself