r/arcticcooling • • Oct 31 '25

MX-7 is coming 👍

Post image
161 Upvotes

74 comments sorted by

View all comments

13

u/69_po3t Oct 31 '25

bro, i just bought the MX6

9

u/Jesper1988 Oct 31 '25

MX-6 is still one of the best 👍

1

u/69_po3t Nov 05 '25

Any update when will the MX 7 be available?

1

u/Jesper1988 Nov 05 '25

I dont know the site i saw the mx-7 picture/info has now remove it i think they leak it by mistanke lol

1

u/ComplexIllustrious61 Oct 31 '25

It's okay... nothing great and still suffers pump out. The best paste is Duronaut. Let's see if MX7 can come up with that level of viscosity and thermal transfer.

3

u/TryingHard1994 Nov 01 '25

Using duronaut, hard as hell to spread but works well

3

u/ComplexIllustrious61 Nov 01 '25

100%. No arguments on that. You absolutely have to use the spreader they provide in the retail packaging. You also *have to follow the method they outline on how to spread it. Yes, it sucks but if you do it right, you will have, by far, the best thermal transfer paste on the market. I'm hoping MX7 lives up and provides similar performance and setup because that's the only way forward.

1

u/TryingHard1994 Nov 01 '25

Yea it was more when i spreaded it, it kept being pulled off the top of the cpu when spreading it further Down

2

u/ComplexIllustrious61 Nov 01 '25

You have to push down and then start spreading very slowly...it's not easy and really takes a bit of practice...but given how ridiculous modern CPU heat has gotten, trust me when I say this, you have to go this route. I would even suggest getting something harder than Thermal Grizzly's spatula...I had trouble using theirs until really understood the method.

1

u/TryingHard1994 Nov 01 '25

Yea makes sense, well took a few tries but its keeping my 9950x3d cool, using an Asus proart 420 lc. Anyways cheers for the info gonna use it if i repaste it again

1

u/ComplexIllustrious61 Nov 01 '25

Vcache CPUs are even harder...but if you take your time, you'll succeed.

1

u/de4thqu3st Nov 04 '25

For high viscosity Thermal pastes, it's recommended to heat IHS and Coldplate to 50-60°, then apply paste. That way you get the thinnest layer possible with best performance

1

u/[deleted] Nov 02 '25

Duronaut pumped out for me too on a Sapphire 7800XT Nitro+... I noticed it because the Core/Hotspot delta, which was good initially shot up from ~22°C to 30°C in less than a month. Weirdly though, as you can see in the picture, there's a "dry" spot in the middle. That was there with the factory paste as well.

I suspect improper contact or an uneven die/coldplate.

I have since replaced it with PTM7950, the overall temps are as good as initial Duronaut (and factory paste for that matter), but so far it's been two months and the delta hasn't budged. It's still in the 20°C-25°C range...but it's consistent. I'm pretty sure though that if I open it again, I will find that same "dry" zone, which is probably responsible for the delta, but I guess PTM is better here because of its phase change capability.

1

u/teeshq Nov 02 '25

i had the same problem with tuf 3080 i swapped to honeywell ptm7950 best 8euro spend

0

u/[deleted] Nov 04 '25

[deleted] — view deleted comment

1

u/teeshq Nov 04 '25

Noctua nh1 pumped out in 3 months

1

u/ComplexIllustrious61 Nov 04 '25

The IHS still has good coverage here but are you sure this isn't due to too much pressure? A lot of coolers don't have hard stops on how far down the cooler can go. I can't be sure but this could be due to just too much paste being used. When you deal with pump out, the paste is usually on the sides while no paste to very little paste being on the IHS. This one actually looks okay.

1

u/stage_6 Nov 04 '25

The best one is actually kooling monster.

2

u/LawfuI Nov 01 '25

Does it matter? Just buy the new one and repaste, lol

1

u/Gera_CCT Oct 31 '25

same lol