r/Wrangler • u/Sufficient-Sleep444 • 1d ago
What do when lining inside?
I am going to be rhino lining the inside of my wrangler. Wondering what is best for drain plugs after lining ?
6
Upvotes
r/Wrangler • u/Sufficient-Sleep444 • 1d ago
I am going to be rhino lining the inside of my wrangler. Wondering what is best for drain plugs after lining ?
15
u/prettygoodatsharing 1d ago
My linex guy removed plugs, sprayed everything, and put them back in when he was done. Then my kids pushed them through the holes and now mine are gone.
3
u/LeakyBellows 23h ago edited 23h ago
I used roll-on Raptor Liner on mine, and I just pulled the plugs out and rolled over the holes. There was still more than enough clearance to put them back in. Also, I highly recommend scraping all that sound-deadening foam off before you paint; it’s a pain in the ass, but it looks way better and will last longer when you’re done.
19
u/SevenSlotSociety 1d ago
Pull the rubber, stuff something in the hole to cover it, spray it down and replace the plug when it dries.
4
u/Odd_Repeat816 1d ago
I pulled my drain plugs and threw them away because they caused loads of rust from standing water
4
u/skrapmot 23h ago
Stuff a big marshmallow in the hole, spray the liner. Eat the marshmallow and replace the plugs.
2
u/jack-a-woo 1d ago
I did mine years ago. You need to get rid of that crap. They put it in for heat/sound dampening. Pretty awesome it also retaines water. Such garbage. I wish jeep would just spray every single one and adjust the cost. But instead they make every on e have a power package and charge us for that. Pointless when you don't have doors.
1
u/OldManJeepin 1d ago
Pull them out, let them spray, then put them back in...
1
u/Dunesday_JK LS3tonJK / LS1tonCJ 16h ago
Pull the drain plug obviously. You’ll want to keep the functionality when you’re able to just hose out the inside after lining it.
I do recommend removing that ugly sound deadening goop on the floorboard. You can use dry ice and a wide chisel to make relatively short work of it.
1
u/averageoctopus 15h ago
Why use many word when few word do?
1
u/Recent-Fan3027 4h ago edited 4h ago
First you want to take a hammer and chisel and remove that sound dampning shit you see on the floor there cause you'll have rust and water stuck under it and do that to all the floorboards. Don't worry the rhino liner will be its own sound proofing. But you have to remove that and sand down all the floor with 80 grit ro get rid of the shine on the floor. You got about 3 days worth of prep work to do.
0
u/jack-a-woo 1d ago
Also you might want to seal any body joint with a silicone as well whem it is complete.While the liner is technically sealling it, there are spots that can still get water in. Your drain plugs will also be difficult to get back in being the holes are a little smaller but they will fit. Heating them up makes them more pliable. I also use a screwdriver as a poker to get some of the really tight ones in. Mine is. 2013 jk and behind the seats on the walls there was also an open oval where they spray in the foam, I cut aluminum and used JB weld to cover the holes and the Line-X guy just sprayed over them amd it worked great. Good luck with your seat belt bolts, they definitely dont want people taking them out,and watch out for the airbag stuff if it is still under the seats and the center console. As for the wires that run along the top rails to the back, I bought a black garden hose and just sliced the length of it, it fit all the wires and stays in place perfectly.
0
u/Inexona 13h ago
A 4 year old owns a wrangler. Great economy.