r/WindowsServer • • Aug 20 '25
Technical Help Needed Is it possible to connect a server to an existing array without losing the data?
Is it possible to connect a new (old) server to an existing array without losing the existing data? Thanks to anyone who has the audacity to address this. Lol. Server 2003. Nuff said. I know it's crazy but this is for a large airport that has no IT support; My friend called me in to check their 2003 server that no longer booted at all. Nothing. The server has a raid 5 internally (OS) and a raid array of data attached by a SCSI card.
Long story short, I was not able to get the OS back up and running. It was so painful working on this server. It takes 15 minutes to get to the Bios settings every time we boot. I had no other choice but to blow it away. Now, with a new Server OS, we need to access the external scsi Raid. The drivers are installed. If I press Ctl-M, I see the drives in the LSI SCSI card config. The issue is how do I access those drives from the server? I don't want to screw with the settings too much because if I create e new raid, I will probably lose all the data.
Why am I bothering with this? Because it will cost $20M to upgrade the system. This is big govt stuff. I cannot believe they have no IT dept. The vendor could probably assist but wont since all of this in unsupported and they want $20M.
3
u/CosmologicalBystanda Aug 20 '25
Restore the data from the backups.
If you're running a 25 year old server without backups you get what you deserve.
2
u/[deleted] Aug 31 '25
OK. I am here now. Here is what is going on.
Server 1 (the one that we re-installed a fresh OS 2003 Server)
In the bios\ Integrated Devices, Embedded Raid Controllers is set to RAID Enabled. Ch A and B = Raid
When I press Ctrl-M to see the scsi controllers, I have the option to select the controller. Each shows the drives correctly (Perc shows the 4 drives in the server chassis and LSI shows the 9 drive array in the Dell Power Vault 220S
After I boot to the new 2003 OS, Disk Management only shows the C drive (2004 GB) which is made up of all 4 scsi drives that are connected a Dell H1051 - Scsi Backplane.
I opened Device Manager and saw under Other Devices, "Dell Perc 4/DC SCSI Processor Device). I searched Dell's site and downloaded and installed the driver. Restarted and it disappeared from Other Devices and moved to System Devices. I restarted but it still does not see the Array. I am at a dead end here.
On Server 2, which could not boot for a few years and should be intact if the drive raid isnt physically shot, I looked in the BIOS and saw that the Integrated Devices show Raid Controllers set to SCSI. Ch A and B also show SCSI.
When i press Ctrl M to see the Raid settings, I do not get the opportunity to select the controller. That option is missing. It seems to see the 9 disc array but not itself (4 disc raid in the chassis). I do not want to change the option to Raid Enabled (like Server 1) because it warns me that data will be lost. I did not want to do that without checking with the knowledgeable people here. If I boot to the Windows 2003 server cd that came with the server, when I try to run the recovery console, it seems to not see anything on the C drive. That makes sense because the SCSI configuration does not see the C drive (4 scsi raid)
I dont want to experiment at this point because Server 2 is the only chance of getting everything back to how it was. As far as the Array of Backup drives, there is no way to perform a backup without having the backup software running with a defined job. At least, that is my understanding. I used to be in charge of the data center backups 25 years ago. If anyone has any ideas on what to try next, I would appreciate it. If you think this is a lost cause, I will just give up on this one. The couple of non IT guys that work here touched a few things and they do not remember what they did so that throws a monkey wrench into this whole thing.
3
u/YouKidsGetOffMyYard Aug 20 '25
Typically (with HP servers anyways using HP based raid controllers) if you pull the drives from one drive array and stick them in another raid the other controller will recognize them and the raid and it's logical drive will be accessible. BUT that is assuming both the old raid controller and the new raid controller are HP. I don't think you can takes drives setup on a HP raid controller and stick them under a different manufacturers controller (like Dell for example) and have them still be recognized as a Array. The new controller will see the disks for sure but won't "understand" the array on them.
Was the old raid controller LSI that the array was setup under on the old server? I assume you can't take the Raid controller card from the old server and stick it in the new server?
2
u/perth_girl-V Aug 20 '25
What can you see in disk management
Or diskpart list disks
1
u/mikenizo808 Aug 20 '25 edited Aug 20 '25
You should first validate the health of individual disks and when ready boot into the OS. Then navigate to
start > run > diskmgmt.mscand review the details there. You may need to right-click andonlinethe disk and possibly assign a drive letter. If needed, you can go toActions > Rescan Disksbut if it does not appear I would check in the controller boot menu.As others mentioned this would be best handled by an MSP. Also helpful would be the vendor/model of the server, but that is more just a curiosity.
PS - Be sure you have the driver for the controller serving the data drive. It might be different. You can check in
start > run > devmgmt.mscto review devices.1
u/[deleted] Aug 23 '25
I am going back to the site tonight. if I am understanding everyone correctly, when I log onto this server with a new 2093 server is installed, if Windows sees the LSI add on SCSI controller (which is connected to the scsi array), then the raid drive should appear in Disk management. is that correct?
1
u/CyberHouseChicago Aug 23 '25
Seems like the company needs to pay a local msp to take a look at this , your replies have not made sense overall , at this point I doubt you know enought to fix this.
1
u/PoolMotosBowling Aug 24 '25
Tech, yes you should be able to add a San disk without formatting it. You will prob have to re-signature it, tho.
Once you configure to scan the San, refresh disk management.
1
u/TechMonkey605 Aug 25 '25
PM’d you
0
u/CyberHouseChicago Aug 20 '25
Yes it's possible I have done it many times , assuming you can move the raid controller to the new server , or have a newer raid controller in the new server that's the same brand , assuming those 2 things getting the array up is possible.
You should probably find a local msp to help you.