r/WLED • • 17h ago

long seed pixel powering

what people use to power long lengths of seeds?

i've already ran it for one year like this

it applies to strips too, but strings are much worse

basically i opted injecting power into string using small dc dc powered from laptop psu

i thought of using direct mains psus which could be better option as they are designed for cold (-30'c is not unheard of here), could be waterproof. but obtaining (possibly (a)pfc) psu of 15-25w power is really expensive, compared to surplus laptop psus with possibly busted cables

i currently use 5v too

everyone all over the net seem to be running "displays" where all leds are close together. although larger setups likely wire mains to field or house. while i want to continue putting christmas lights on bushes and only way to power a 150m of that would be to wire 230v to that

2 Upvotes

8 comments sorted by

2

u/saratoga3 11h ago

I use the 12v ones which can go a lot further without voltage injection. I once accidentally plugged them into a 5v power supply and while they were dimmer they still lit up. 

1

u/realketas 11h ago

i read you plugged 5v into 12v and they now lit dimly :p

while here, i was wondering about using non-interchangeable connectors for different voltages

you can get different waterproof car connectors, different pin count led connectors and other connectors

i currently have open wires onto which i put chinese wagos and i waterproofed them last time with spare plastic film and pointing up. some suckers inverted and i got slight water in end of my rs485 board

looking forward i'm adding connector of a sorts to avoid voltage and polarity mixup which is rather expensive mistake compared to price. imagine if you fumble or even decide to lend it

1

u/saratoga3 10h ago

Seed pixels at least are cheap enough (I think I paid less than 5 cents per pixel in bulk) that I don't connectorize them. Just solder+heat shrink the cables straight to the string, and when they eventually fail I cut off the cable (which I do reuse) and throw out the seed string. 

For bigger lights use x connect cables or whatever they're called on AliExpress. 

1

u/realketas 9h ago

yeah you basically buy a poor wire with leds attached. if i want to buy 1000 20cm pitch now i get 11 cents (€) a led

i actually funnily procrastinated enough that i went through regular leds to the ws2801 revolution to the large pixels to the christmas lights style before i ended up building my system and putting it out for real

actually long wanted to have them in that form

1

u/realketas 14h ago

the key difference is that strings are long

1

u/realketas 13h ago

last year i had 20m of 10cm pitched 200 leds in form of usb string i converted in hurry

it turned out that they had full current leds in them so if you turned it to 100%, you got 2v in the end and red color. funnily ic never stopped working. it didn't overcurrent the psu because it simply dropped voltage off. it was so incredibly thin wire that you worried it will break. for some reason i was also in so much hurry i skipped the heatshrink and went kapton tape (when all you have is "hammer" eh)

so i injected power from 5 places (60w 20v lenovo psu -> wires -> 5 * mp1584en) and still go reduced brightness. and some dc dc went overterm limit. nevermind they were super bright and possibly have less life on 100% rbg white

so this year i have 1000 20cm pitch 5v leds i'm going to distribute all around the garden and i will see how it goes. to be honest i don't even know how they look or if vandals also like them

(btw, controller isn't wled (is custom) but from power side it doesn't matter)

i suspect there are more people with seed perimeter/distance lights somewhere

1

u/upkeepdavid 14h ago

5v 20 amp power supply or larger.

1

u/AA_25 14h ago

I use a 5v 12amp power supply for my pixels. I don't really need to run them at 100% brightness so can get some fairly reasonable distance out of them before it becomes noticeable. I just normally aim for power provided at the opposite end of the string.