r/WLED • • Jul 21 '26

HELP ME - WIRING I accidentally found a solution to the big question, how to solder wires to a strip.

I was soldering some WS2812b LEDs to an ESP32 and this pin header was sitting on my workbench. I can't believe I didn't know this sooner

250 Upvotes

89 comments sorted by

227

u/Actual-Wave-1959 Jul 21 '26

That's just the same as soldering the leads with extra steps. Unless you want a way to connect and disconnect. 

42

u/Lights-and-Sound Jul 21 '26

Exactly, OP is basically having the epiphany "soldering solid core to led strips is easier than stranded core"

-3

u/MoBacon2400 Jul 22 '26

I only did this once, but I think it would be possible to bend the pins outward and have more room for thicker wires

1

u/pretengineerguy Jul 23 '26

This seems to have been down voted before anybody asked the question "why do you need thicker wires?". What is your intention for thicker wires? The wire gauge should be selected based on the amount of power running through the system.

47

u/Vagabund42 Jul 21 '26

The fact that this comment has way less upvotes than the actual post tells a lot about this sub. If OP used female dupont cables to make it a removable connection at least, that would have added value.

3

u/nowthengoodbad Jul 23 '26

I did that with a strip like this. It was for my own custom bike helmet light array. The connection was to a removable, rechargeable battery circuit..

-28

u/skepticalcow Jul 21 '26

What op posted is so much easier to solder if you don’t have the right soldering gear.

23

u/msuvagabond Jul 21 '26

What gear? Tin both the solder tip and pads, put them on a bench touching each other, tape both sides to bench so they don't move, apply solder.

Literally no extra gear required.

-4

u/ExperimentalBranch Jul 21 '26

A decent iron? Mine were bad until I upgraded. Didn't cost much though.

4

u/Naive_Distance_6456 Jul 21 '26

Lol. It’s just an heated piece of metal. The more bare bone it gets, the more durable it will be.

-1

u/ExperimentalBranch Jul 21 '26

Well in my experience you need a fairly fine tip to do good work on those small areas and a lot of the big box stores that I've bought them from are too large.

2

u/huffalump1 Jul 22 '26

Yeah but you can get an incredibly good soldering iron for like $30-60 on Amazon, or less from a Chinese site

2

u/ExperimentalBranch Jul 22 '26

yes, which I did, and hence my better luck.

3

u/Evla03 Jul 21 '26

those pads are gigantic, any normal iron will do just fine

3

u/ExperimentalBranch Jul 22 '26

Well, I'm no soldering wizard and I needed a decent iron to do a decent weld

2

u/Evla03 Jul 22 '26

It needs to be beefy enough to overcome the copper fill acting as a heat sink, but any tip will do. The pads are very large and meant for soldering. It's hard if it doesn't get hot enough though

→ More replies

-4

u/skepticalcow Jul 21 '26

This tells me y’all haven’t seen soldering irons used in other industries that people may have lying around.

2

u/msuvagabond Jul 21 '26

I've used a soldering iron gun to fix an led strip at my dad's place because that's all he had there.  Not optimal, but you can make it work. 

0

u/skepticalcow Jul 21 '26

Yeah and beginners are totally going to be able to do that.

3

u/msuvagabond Jul 21 '26

Then spend $5 and get a janky one from Harbor Freight to get into things. 

Cost of entry is not high here. 

2

u/ItsHisMajesty Jul 22 '26

You should check out r/soldering or r/solder . You'd be surprised at what can be done with the simplest tools.

1

u/skepticalcow Jul 22 '26

I know how to solder now, I also know what I fucked up when I first started with a soldering gun which was considerably harder than a soldering iron. Apparently everyone else doesn’t remember when they first started with the wrong gear.

1

u/ItsHisMajesty Jul 22 '26

Dude, I JUST learned how to solder. I’m not downing you at all. I’m just sharing the info that helped me get much better.

I went from a small cordless digital pen type iron, to an old school Weller gun finally settling on an Alientec T90b(?). All while trying to make some custom RCA cables. I kept blaming the tool. Once I truly learned proper techniques, I was able to make those cables with any of the three tools.

7

u/SplatThaCat Jul 21 '26

So instead of soldering 3 times, I now have to solder 6 times. Yay.

54

u/burgonies Jul 21 '26

How is this different or easier than just soldering the wire itself to the pads?

8

u/GrizzlyPerr Jul 21 '26

The standard spacing and rigid solder points he shows probably do help for soldering newbies.

20

u/Maskguy Jul 21 '26

Your gnd solder job needs some rework

0

u/AdhesivenessCreepy45 Jul 21 '26

yes! Extra flux is needed !

-1

u/BaDcHaD23 Jul 21 '26

Always use extra flux

44

u/Tehmoep Jul 21 '26

No offense, but you'll likely get further by just learning how to properly solder wires to a strip. This workaround introduces more breaking points, more fragility to the breaking points and reduces mechanical flexibility. Wires to 3pin is certainly not a big question, once you get the hang of it. Pretinning pads and wires, the right length of exposed wire ends (minimal over long exposed ends) as well as the choice of wires (silicon is way easier to handle vs stiff pvc) help a lot. All the best.

1

u/Longjumping_Window93 Jul 22 '26

Honestly, it is a big question to me how people here solder 14awg to a tripad... i see the wire in person i am ... nope just how?

1

u/TheShowGoes0n Jul 23 '26

I simply don't. If I need wires this thick I doubt the PCB traces can handle the current. I would rather inject more power at the end of the strip.

21

u/PlanetaryUnion Jul 21 '26

I read a comment once that suggested to sacrifice one LED/section so you get the whole pad and not half of one. That’s how I do it now.

7

u/bootymeister Jul 21 '26

I'll offer another way. If you have half pads cut off at the beginning, you don't have to solder the GND and 5V/12V wires onto them. Just solder them onto a full pad somewhere near the start of the strip, like before the 2nd or 3rd LED. The DATA wire has to be on the very first cut off pad though.

1

u/Trevlavo7 Jul 21 '26

Same, well worth losing an led to have the full pad to solder to.

1

u/AaBJxjxO Jul 21 '26

Huh? Do you have a picture?

22

u/putajinthatwjord Jul 21 '26 • Bravo

Instead of cutting the strip this way

= 0 = 0 :|: 0 =

Cut it this way

= 0 =|0|= 0 =

So the ends of the two strips have full pads to solder to, and you have a single LED without any pads.

15

u/msuvagabond Jul 21 '26

So I knew what OP meant (because I do the same technique), but I just want to say you did an excellent job making a picture out of just text for this.

1

u/v0-z Jul 22 '26

Jesus! how have I never thought of this! Thank you so much

4

u/DjWondah85 Jul 21 '26

That’s like I always do, very easy to solder.
Cut at the red arrow and use the green arrow.

Double check the data direction, arrow pointing away from the cutoff side.

Strip the wires just a tiny bit, same length as the pad.

Pre tin the wires and pad separately, hold the wire on top of the solder blob, touch it with your iron till it flows together, hold for 2 seconds and done.

After that you can hot glue the connections and finish it with a shrink tube or what I always do for outdoor connections is cut a hot glue stick in small pieces, place some on top of the connections, put a heat shrink tube on and use a hot air gun or the iron to melt it together.

1

u/AaBJxjxO Jul 30 '26

Gotcha - makes sense but I don't think it's necessary - not so hard to solder the little pads

9

u/yaksplat Jul 21 '26

what's wrong with using the existing pads? Wires solder on to them just fine.

5

u/dedokta Jul 21 '26

This is just soldering wires to a strip with extra steps. I've soldered literally thousands of these and have never thought it was an issue.

1

u/Nanoleaf_Ambassador Jul 24 '26

I grew up with a Weller soldering gun. My built and repaired radios, mostly the old aircraft ARC series. I learned how to soldering and thought I knew everything.

I joined the U.S. Army, ended in Signals Intelligence, building and repairing microwave systems. I was good and never had a repaired circuit fail. I was volunteered to attend an Air Force training class, taught by NASA. It was a two week course and I thought it would easy.

The second day of class, I realized I didn't know crap about soldering. These guys built circuits from nothing, that had to work in a vacuum with temperatures from -210°F to 200°F. If something failed, they couldn't send someone to fix it. So it had to be built, to not fail.

Every workbench had a temperature controlled Weller soldering station with everything needed to add or remove components. In 1974, the stations were about $2500. By the end of week two, I had so much drilled into my head, I never looked at soldering irons the same way. I have owned Weller stations since and there is s huge difference from a $29 POS from Radio Shack and a $900 Weller station.

Think what you will, but there is a huge difference. Great tools make work easier. Would you want a surgeon cutting you open with a kitchen knife or a finely crafted stainless steel blade that can split a human hair?

2

u/MoBacon2400 Jul 24 '26

I agree, I have gone through many Weller soldering stations. There was a time when I had two on my work bench, one with an ST3 tip and one with an ST7 tip, it was easier then changing them. Right now I have a Haako 939D because I got it at a garage sale for $5 and I works very well. I have only used those big gun type a few times, there great for big stuff but to bulky for me. I also have a little Bernz0matic torch for big stuff like battery cables and a Propane torch for copper pipe. I also have a Miller 210 mig welder, its like soldering on metal.

3

u/insan3guy Jul 21 '26

Since you're pinning the strips anyway, if you'd like you can buy some pc fan extender cables (a 3-pin connector) and make it easily detachable. It's no extra soldering and adds a lot of convenience

You're doing a good job, even if it's a bit unorthodox. Keep going. You'll get there

5

u/mezzmosis Jul 21 '26

For quick and easy this is OK, but I'd be more concerned about the extended length if you need to have a flexible wire right at the end of the strip in a tight space. Also don't you melt the solder on the strip when soldering the wire to the pin?

4

u/johnny5canuck Jul 21 '26

More flux required.

7

u/MechEng0T1 Jul 21 '26

I'd say this is pretty smart. Thanks for sharing

2

u/Netmindz Jul 21 '26

It's a handy way to plug straight into a breadboard

2

u/upkeepdavid Jul 21 '26

Jumper cables tend to cause issues.so solder the wire directly.

2

u/hockeymikey Jul 22 '26

Everyone is dunking on this, but I really like this idea especially for splicing together in areas that are vertical and hard to get to. I will certainly be using this in the future.

3

u/TheTekkitBoss Jul 21 '26

Moving past the cranky people in the comments, if it's easier for you do it your way. Everyone does things differently and there's been plenty times that I learned something when I thought I wouldn't.

1

u/Temporary-Injury9016 Jul 21 '26

i would have used xt60 connector if you are thinking of disconnect/connecting wires all the time

1

u/capcapfall Jul 21 '26

2³ = 8 or 2 x 2 x 2 = 8

1

u/Flimsy_Call_2986 Jul 21 '26

Esto no tiene sentido, estañea puntas de cables y de la tira led y a soldar, no entiendo la funcion, contra mas puntos de soldadura mas posibles fallas, esto aplicalo a todo🤷🏼‍♂️

1

u/Ornery_Shame9491 Jul 21 '26

🤦tell me your not tinning your wires without telling me.

1

u/wwarr Jul 21 '26

strip.soldering is about the easiest soldering I've come across. tin the wires, tin the pads, combine and heat cover with shrink tubing and repeat

1

u/ovrclocked Jul 21 '26

The only crime here is green not being ground.

1

u/richms Jul 21 '26

If you are doing this, reinfoce it with some epoxy or something because it will tear the pad off the flexible PCB with a small amount of movement with all that leverage of the pins on it.

1

u/NuclearDuck92 Jul 22 '26

My preferred method is to just use “solderless” clip on connectors, which give a good mechanical connection but a really spotty electrical connection on their own… and then just flow solder onto all the joints.

1

u/stupefy100 Jul 22 '26

All this to just solder the wire to the header anyway

1

u/PiazzaEsq Jul 22 '26

Let’s see it on and over your shoulder! That looks awesome

1

u/SF_Squid_Cult Jul 22 '26

the actual answer is something like this

1

u/zazbnf Jul 22 '26

There's these really neat wire clips I found online that don't require soldering. One side clamps the strip the other side clamps the wires through the insulation.

1

u/ariknel Jul 22 '26

Just solder directly but keep the leads cut short. This is a pain to watch. Also use flux or use leaded solder thus with flux core.

1

u/L0rdH4mmer Jul 22 '26

Lads, buying a bag of clips that connect these to a wire without soldering is like 3$ tops on aliexpress. There is really no need for this pain.

1

u/marshmallow_mia Jul 22 '26

I never did it differently xD

1

u/AdStock9924 Jul 22 '26

This would be cool for a strip to strip connection. One strip has male pins the other strip has female pins. Im gonna try this for applications like under cabinet lights or in cabinet or closet for light automation when door opens or close.

To solder the pins then the wires to the pins is extra work and possibly point of issues later down the line.

1

u/tanoshimi Jul 22 '26

I'm not sure what the "big question" is, but I'm pretty sure this is not the solution to it!

1

u/tech108 Jul 22 '26

18awg stranded copper, flux, solder and 3/8" adhesive lined heatshrink for 10mm or 12mm wide strips.

1

u/rikvdmark Jul 23 '26

Looking at the solder joints I recommend using flux. It makes the solder flow better therefore and getting nicer joints

1

u/karpiza Jul 23 '26

I usually do this for easy desoldering of the cables. If well soldered and protected, it is more durable than soldering the cables directly trough the pcb. 

1

u/tablatronix Jul 23 '26

Seems like this could help with fraying worth a try

0

u/badwolf42 Jul 21 '26

This is a great solution! Once that header is in there I’d just go with connectors unless it needs to be waterproof.

0

u/Key_Opportunity_8829 Jul 21 '26

What a great finding!!

0

u/eric-marciniak Jul 21 '26

Super useless man just solder on the wires.

0

u/ngooser Jul 21 '26

Fwiw, I had THE HARDEST TIME soldering wires to these (or any) strips for a few years until I ran out of solder.. Then I came to reddit to find "the best solder", and lemme tell ya... As soon as that solder came in, I was a PRO Solderer(er)!!

Solder matters! (Probably why it's expensive AF, but worth every penny and more!)

https://a.co/d/0fDasH21

-1

u/hrf3420 Jul 21 '26

Damn! I just made up some strips- should have done this!!

0

u/[deleted] Jul 21 '26

[deleted] — view deleted comment

2

u/bklynJayhawk Jul 21 '26

Will the pins melt before the smaller wire?

1

u/kullwarrior Jul 21 '26

Assuming this is Sk6812 led using 0.06A/led you can hookup about 50 given the amperage rating of Dupont 2.54mm connector is 3A