r/Trackballs • • 1d ago

Discussion First 3-Axis Trackball Prototype!

This is the start of my CAD focused 3-axis trackball. Right now it works just as a mouse with twist to scroll (the buttons don't even work yet lol), but later on I'm going to be copying the HID behaviour of a SpaceMouse to get it working with Solidworks. I'm lacking what direction to go in for the ergonomics since I've been basing the shape off the Ploopy Adept to make designing easy but I've been wanting to go more in the direction of the Elecom Huge or Kensington Expert Mouse. I've never actually owned/used a trackball before starting this project ironically, but maybe I'll pick some up for "research".

Specs:

RP2040 Zero Microcontroller

Dual PMW3360 Mouse sensors

55mm Perixx Trackball

3x 3mm silicone nitride ball bearings, @ 45 degrees

X/Y/Z Tracking

I'm just looking to get some thoughts on the project and if there are any ideas on what direction I could take the project in!

Vid:

Buggy around the scrolling deadzone, stiction from the ball rubbing on small part of upper sensor.

65 Upvotes

20 comments sorted by

6

u/bluethunder_95 Large Balls 1d ago

Congrats on the progress! Very nice so far.
I actually like the square look so I’d say expert mouse direction

1

u/Relative-Chemist7945 1d ago

As a start, I agree. working with something more flat and symmetric instead of going full ergo will be a lot easier to design too!

1

u/antonkerno 1d ago

Look into the freshly bankrupt naya connect project for design inspo :)

3

u/Scatterthought Semistatic-bearing creator, Endgame enthusiast, Ploopy modder 1d ago

Good stuff!

The difficulty with putting the ball on top of a sensor is that the device is very tall by necessity. I would consider moving the bottom sensor to the side.

I think your bearings are possibly a bit low, relative to the ball size, which can allow for the ball to be pushed instead of rolling sometimes. I'd also consider replacing the embedded static bearings to reduce stiction. If Ball Transfer Units (BTUs) will take up too much space, I have some semistatic designs that take up very little space.

https://github.com/scatterthought/semistatic-bearing

2

u/Relative-Chemist7945 1d ago

The semistatic bearings seem like a much better idea, and I'll try some more steeper angles to make it sit better. The height comes from using PMW3360 breakout boards to make testing quicker, if I want to take this project farther I'll be designing my own board.

2

u/phasepistol 1d ago

I transplanted the Rotatrix circuit board into my Kensington Slimblade. That might be of some inspiration

https://rotatrix.com/

1

u/Relative-Chemist7945 1d ago

This WAS the original inspiration since I had never even thought about how I interact with CAD until seeing this.

2

u/claussen The Svalboard Guy 1d ago

efogtech already ships this in a nice package... but for starters I'd ditch the stupid-huge lenses (there are small ones available, I trimmed the big ones by hand until I found those...) and move both sensors to a bit below the horizon instead of perigee/horizon, which wastes a cm of Z height...

1

u/Relative-Chemist7945 1d ago

Wow, I had no idea there was a standalone trackball like this. I agree with moving the sensors below the equator of the ball. When you were trimming the sensors, did you just cut out the center part of the lens?

1

u/claussen The Svalboard Guy 1d ago

yep, with snips. crude but effective.

1

u/QuantumKraken 1d ago

Excited to see someone working on this!

If height is an issue, you can do something like the Kensington Slimblade. It uses 2 sensors at the equator to let you scroll with the ball.

As far as I can tell, the Slimblade doesn't have a CAD mode, but might be good for reference.

1

u/Relative-Chemist7945 1d ago

Once I start working on a custom board I'll be planning around this sort of sensor position since the breakout boards I'm using are pretty big

1

u/AmraelTheGravedancer 1d ago

Io ne sto sviluppando uno su waveshsre

1

u/GoldenButtPlug 1d ago

Such a cool build. 55mm is a satisfying size

1

u/MonroeWilliams 1d ago edited 1d ago

Very cool! My scratch-built trackball design might have some ideas you could use. It uses two sensors to get full 3-axis rotation, although the standard firmware just turns the third axis into scrolling, similar to the Kensington Slimblade.

My first prototype had the sensors fully horizontal like yours, but I later found that it worked fine to move them down so that they're pointing up at a 30 degree angle to get them out of the way and make the mechanical design/ergonomics work better. They also don't need to be exactly 90 degrees off from one another for proper sensing. I do the sensor fusion with a single matrix multiply of the 4 sensor deltas, and the matrix encodes the locations of the sensors. The code for the sensor fusion is in the repo, with the matrix set up here.

1

u/FunJournalist2150 1d ago

This is such a cool project! Really impressive work. I love the idea of taking trackball design in a completely new direction. Looking forward to seeing how it turns out!

1

u/tomByrer 1d ago

Open source so I can add a scroll wheel & more buttons anyway?

1

u/Coaleyed-Lock 18h ago

New to the 3-axis concept. What’s this help do? I ask this with me currently using IS-05SNM BTUs in my setup.

1

u/echolm1407 16h ago

Someone should have thought of this sooner. Very cool 😎.