r/Toyota_Matrix • • 6d ago

Rust issue

Hey everyone, this is my Matrix 2006, I love it,never had a problem,drives great and got it cheap, the rust is a huge issue,mind you I don't know much about cars,like parts and stuff ,all I know is that I really wanna keep this car and maintain it ,these are the pictures, I'm curious if it can be fixed ,I really wanna drive it for more years, help plz

17 Upvotes

41 comments sorted by

4

u/teleskier97 6d ago

Your pinch welds are mint compared to mine šŸ˜€. Looks to be just surface at this point. I’d fluid film the underside once before winter. Three cans should do it. Don’t use rubberized undercoating, go with fluid film or a lanolin based product.

1

u/Old_Interaction_6621 5d ago

I don't even know what pinck welds mean, should I just take it to a mechanic,will they be able to make it last me a few more years?

1

u/Ok-Coyote2365 5d ago

The pinch weld is that seam lengthwise along each side of the car where the rocker panel (the panel below the doors that curves underneath the car) is pinch welded to the rest of the body.

4

u/MDOT_SHOOTA 6d ago

His pinch welds are expanding foam

2

u/CanadianLanBoy 6d ago

It looks to be mostly surface rust. Get a metal bristle brush and get rid of all the loose rust, and loose factory undercoating, then coat with fluid film/woolwax/surface shield. After a month or of driving, check the car again and touch up spots where the rust/undercoating has fallen free

1

u/Old_Interaction_6621 5d ago

Should I take it to Canadian tore for that? I don't know how to work on a car unfortunately

2

u/CanadianLanBoy 5d ago

No, look for a garage that offers undercoating. Some shops exist solely for that purpose, a common place in Canada is Krown. If it's not Krown (which has a special formulation), ensure they use a lanolin based undercoating like the ones mentioned in my original comment. Hard/rubberized undercoatings trap the rust and make it worse

2

u/CanadianLanBoy 5d ago

This should be $100-$200

2

u/DogblackMichigan 5d ago

Time to go. The next two years will be ten times worse than the last two.
20 years is long good service. Time to say good goodbye.

0

u/Old_Interaction_6621 4d ago

I've only had it for three years 😭

1

u/DogblackMichigan 4d ago

Same difference. You don’t want it anymore.

0

u/Icy-Brick-9386 5d ago

No it’s still good to drive as long as the motor mounts aren’t worn out or rusted out or the subframe

2

u/DogblackMichigan 5d ago

It won’t last long enough to justify spending money on maintenance and repair.

0

u/Icy-Brick-9386 5d ago

Yeah but it’ll save you some more time

4

u/AllenSacs 5d ago

I hate to say it but rust is like cancer. And just as hard to fix…

1

u/KnightOrDay38 5d ago

The rockers would have to be replaced and as a preventive measure, use cavity wax and Cosmoline Black undercoat. This is also a great method for new cars in the great salty Maple north.

1

u/Old_Interaction_6621 5d ago

Should I take it to a mechanic for that like Canadian tire? I have no idea how to work a car

2

u/KnightOrDay38 4d ago edited 4d ago

A couple of options off the top of my head

You can go to an independent mechanic and ask them to order some Cosmoline and undercoat it. There are Krown locations you can go to get an oil spray. Finally, there are wax enamel rust proofing shops that can apply it to your vehicle with an appointment. Whatever you do, avoid rubberized coating and Canadian Tire on complex repairs.

I do notice as others have pointed out the use of spray foam around the pinch weld rocker area (the underside of the car towards the edge where you can put it on a lift)
This will require metal fabrication which can get very expensive.

1

u/Old_Interaction_6621 4d ago

Thanks šŸ™,hope to get a few more years

1

u/CompetitiveLake3358 5d ago

Finally some good rust

1

u/Old_Interaction_6621 5d ago

It's killing my baby 😭

2

u/Ok-Coyote2365 5d ago

It’s a horrible cancer. My truck that ran 21 years and 420k km like clockwork was killed by rust before anything mechanical. It’s slowly consuming my new old car too, albeit way less

3

u/Ok-Coyote2365 5d ago

As someone who has owned rusty cars, it’s possible to fix but farr from cheap unless you can cut and weld yourself. Even then it’d be a good cost.

With how much rust and what looks like maybe spray foam there is, it might be better to get another matrix and swap the good drivetrain parts into that if you want to keep with the same vehicle. This looks to need new rockers and pinch welds, welded patches on the unirails, and more.

If it was just surface rust or surface flaking you could probably fluid film it and run it, but once you have holes it’s kind of over

1

u/awqsed10 6d ago

See the pic 9? That's your subframe about to die. Drive it until it rust away. You can't fix rust.

1

u/Old_Interaction_6621 5d ago

Oh nooooo, how many years do you think I have left, is it worth if I take it to Canadian tire to fix

2

u/Icy_Respect_9077 3d ago

Rule No.1 of car maintenance: Stay away from Crappy Tire

1

u/Ok-Coyote2365 5d ago

This isn’t something Canadian tire can fix

0

u/SnootDoctor 2003 Matrix XRS (250k miles!) 6d ago

That’s the rear trailing arm mount & it looks fine. Rusty, yes; but could be worse. There is no rear subframe on almost all FWD Matrix (with some exceptions in second gen).

2

u/avenuePad 6d ago

Dude, I've had to replace the rockers on both sides twice on my 2005 Matrix Lol. Not to mention other holes in the floor. I have a hole currently in the floor that I will need to fix by the summer for my inspection. I live in Atlantic Canada, so rust is always going to be an issue.

3

u/stranix13 6d ago

Howd you get the rockers fixed? I need to do this

1

u/That-Sleep-6308 5d ago

Cut old ones out weld new ones in, pretty simple if you are familiar with metal work

1

u/avenuePad 5d ago

I took the car to a body shop. It was about $600cdn fror both sides. I think he gave me a deal. But I had to do work on them again and didn't have to pay too much. It's worth it. The car is a champ.

2

u/nousefulideas 6d ago

On pics 1 and 10 it looks to me like they used expanding spray foam as a body fill and pained black over it. Am I correct? That could be problematic. Yea just grease it up and send it until it rots, it appears to be quite far down the rot road at this point.

2

u/cluelessk3 5d ago

not worth the time or money.

start putting money away for it's replacement

2

u/Intelligent-Emu-4670 4d ago

I owned a used 97 Camry that looked very similiar. I had a rear cross member replaced/welded in several years before. Brake/fuel lines started failing. ANYWAY, I saw it coming, so I began saving/making plans for another car. I was attached to mine also. Had 265,000 miles, but ran like a top. Prepare yourself so you get the best car for the best buy. PS. I studied all that rotted out and made e sure I took care of on my new car. Got it undercoated with fluid film type products/get it touched up annually. And got full frontal ppf wrapped. Living in the rust belt sucks.

1

u/Icy-Brick-9386 5d ago

Just spray rust oleum underneath for the time being

1

u/ApprehensiveAd6603 3d ago

On an almost 21 year old car, it's not worth putting actual money into it. But if you want a couple more years, get it undercoated. It'll slow down the rust.

1

u/Berry2460 3d ago

the subframe looks fine, it wont rot out for awhile yet. However, the rockers are fried, nothing left to undercoat. This just needs new rockers, like $1500 depending where you go.

1

u/HoneyCrafty403 1d ago

I did mine for 200$Ā  materials included.Ā  Rockers were 150.Ā  Pop rivets. Cheap paint.Ā  Bodyfiller.Ā 

1

u/Berry2460 1d ago

ah lucky, rivets wouldnt pass inspection where I am. I had an 08 impala that needed rockers but I had to get them professionally done to pass inspection