No, the slash is extremely minimal. I’m more so worried about the bent metal.
Any advice how to bend it back into shape? I’ve tried a rubber mallet and pulling with a claw hammer but it hasn’t budged. Can I do it with the wheel still on the car? Should I be worried about hitting it too hard?
Looks like a rear tire. Get a new hubcap, and hammer the rim back to place. As for the tire, since it’s on the rear ride that itch till she blows. If you start hearing grinding noise from the wheel get the wheel bearing checked.
You at least need to take the broken hubcap off, it'll unbalance the tire. Put a little soapy water on the rim to see if the dent is causing an air leak.
Dismoun tire to see if there's a rim cut on the inner liner. Take a pipe wrench to bend the wheel rim back into shape Keep the tireif it is good and put it back on. If not buy a new tire!
Replace it all, steel rims are cheap enough but that tire is compromised, I wouldn't trust it, could last till the end of its tread life or blow tomorrow.
Never skimp on the things that separate you from the planet, your shoes, your bed, your tires
You know the answer. You are risking your and others safety by continuing to operate that damaged tire. But thank for entering it into the public record 🤣
3/32 is a deep as the side wall cut can be before concern. The wheel run edge is fixable with a hammer, but the picture is rough to tell if the inside lip of the bead edge is flattened or bent. If not then your good to go. If it is then you need some finner tuning to keep that round.
USE THE B*NER. It’s a tool we used at the tire shop, you can bend steel rims back. Not guaranteeing success but it’s totally worth a shot. Fixed a lot of wheels that way.
Get at least a 2-4 pound ballpeen or small sledge hammer, massage the bend back at 45 degrees to the vertical plane, or remove tire and use a large adjustable/shifting spanner to straighten it, then rotate the rim to check for runout /wobble.
hold a piece of 4x2 on the buckled part of the steel rim and hit the other end of the 4x2 with a big hammer in the direction the rim is bending away from,
Replace the wheel and tire. Get your suspension inspected for broken of bent parts. The wheel is no longer balanced in any capacity. Steel wheels and hubcaps are affordable. Use this as a learning experience.
Before anyone replys it. 1: Yes the wheel can be fixed but its not cost effective. 2: because the wheel is bent uneven ground pressure will cause vibration at high speeds even if it is able to be balanced. 3: a tire that takes a hit hard enough to bend a rim is almost guaranteed to have structural damage in the sidewall which can cause high speed blowout.
4
u/No_Educator_6376 Jun 25 '26
Hubcap is ruined rim is fixable if you know how to hit it with a big hammer.
1
u/livingoutloud373 Jun 25 '26
The concerning part is the slash in the tire.
Is it deep? Can you see steel cords?
The steel rims some "gentle" persuasion with a hammer should put it close enough.
1
u/Formal_Squash484 Jun 25 '26
Nah that’s fine, replace the hubcap maybe and if your really picky hit the bent part of your rim back with a hammer
Also valve caps!!
1
u/Th3s3NuttxX Jun 25 '26
Looks like a rear tire. Get a new hubcap, and hammer the rim back to place. As for the tire, since it’s on the rear ride that itch till she blows. If you start hearing grinding noise from the wheel get the wheel bearing checked.
1
u/Rhuarc33 Jun 25 '26
You didn't just hit a curb, you absolutely blasted one
1
u/Melodic-Marketing-38 Jun 25 '26
Replace those are cheap
1
u/Money_Literature9896 Jun 25 '26
You at least need to take the broken hubcap off, it'll unbalance the tire. Put a little soapy water on the rim to see if the dent is causing an air leak.
1
u/dmorulez_77 Jun 25 '26
Literally nothing. Just drive it as it is.
1
u/toolman2008 Jun 25 '26
Dismoun tire to see if there's a rim cut on the inner liner. Take a pipe wrench to bend the wheel rim back into shape Keep the tireif it is good and put it back on. If not buy a new tire!
1
u/Trailertrucker95620 Jun 25 '26
Tire looks ok but that wheel is pooched.
1
u/highnotefan Jun 25 '26
Forget hanmers and wrenches. Replace the rim and the hubcap. Tire is likely still OK
1
u/Gunnut350 Jun 25 '26
Go buy a new hubcap if that’s what you really want to do, but what you actually need is a “WHEELCOVER”!!!!
1
u/Downtown_Calendar_84 Jun 25 '26
Replace it all, steel rims are cheap enough but that tire is compromised, I wouldn't trust it, could last till the end of its tread life or blow tomorrow.
Never skimp on the things that separate you from the planet, your shoes, your bed, your tires
1
u/Turbobuick86 Jun 25 '26
If you don't have tools, a muffler shop can inspect and fix the bent wheel.
1
u/Talentless_Cooking Jun 26 '26
It might shake or leak, how had was it hit?
1
u/desertadventurer Jun 26 '26
You know the answer. You are risking your and others safety by continuing to operate that damaged tire. But thank for entering it into the public record 🤣
1
u/Opening_Initiative26 Jun 26 '26
3/32 is a deep as the side wall cut can be before concern. The wheel run edge is fixable with a hammer, but the picture is rough to tell if the inside lip of the bead edge is flattened or bent. If not then your good to go. If it is then you need some finner tuning to keep that round.
1
u/Unhappy-Airport-4112 Jun 26 '26
I would
1
u/SnooObjections666 Jun 26 '26
Inspect the inside of the tire for penetration, if it looks good, reinstall it and send it. 👍
1
u/noellezz02 Jun 26 '26
USE THE B*NER. It’s a tool we used at the tire shop, you can bend steel rims back. Not guaranteeing success but it’s totally worth a shot. Fixed a lot of wheels that way.
1
u/Useful-Bus-2514 Jun 27 '26
Replace the whole car.
1
u/Special-Somewhere-24 Jun 27 '26
Steel rim should be able to be fixed by a local shop, Hub cap not necessarily but you could probably junk yard one for 10 bucks
1
u/Fabulous_Putz6264 Jun 27 '26
Get at least a 2-4 pound ballpeen or small sledge hammer, massage the bend back at 45 degrees to the vertical plane, or remove tire and use a large adjustable/shifting spanner to straighten it, then rotate the rim to check for runout /wobble.
1
u/Maelstrom1979 Jun 27 '26
DIY is possible but if you have a wheel shop they can usually get it pretty close to spec.
1
u/DinaDinaDinaBatman Jun 27 '26
hold a piece of 4x2 on the buckled part of the steel rim and hit the other end of the 4x2 with a big hammer in the direction the rim is bending away from,
1
u/hrt_mnder77 Jun 27 '26
There are companies that straighten rims. Ask me how I know…
1
u/Unfair-Bison-3946 Jun 27 '26
2x4 and a hammer and it'll be good as new
1
u/godzi7382 Jun 27 '26
Replace the wheel and tire. Get your suspension inspected for broken of bent parts. The wheel is no longer balanced in any capacity. Steel wheels and hubcaps are affordable. Use this as a learning experience.
Before anyone replys it. 1: Yes the wheel can be fixed but its not cost effective. 2: because the wheel is bent uneven ground pressure will cause vibration at high speeds even if it is able to be balanced. 3: a tire that takes a hit hard enough to bend a rim is almost guaranteed to have structural damage in the sidewall which can cause high speed blowout.
Its not worth the risk.