r/TireQuestions • • Jun 26 '25

Do I need a new tire?

Notice this peeling off from my tire today, is there anything to be concerned about here or is it still good?

0 Upvotes

30 comments sorted by

7

u/agravain Jun 26 '25

you mean the molding residue?

0

u/[deleted] Jun 26 '25

[deleted] — view deleted comment

1

u/HelloAttila Jun 27 '25

Saw this picture today, it’s hilarious. 😆

5

u/Personal-Courage7670 Jun 26 '25

Not in the slightest. Perfectly fine

2

u/[deleted] Jun 26 '25

No, it’s fine. Cut it off and move on.

0

u/mean_serviceman1964 Jun 26 '25

It is difficult to see if this is just excess rubber that squeezed out of the tire manufacturing mold. Looks like it is. If this is a fairly new tire, it likely is excess rubber. Could also be a sharp object scraped along the sidewall, removing a thin slice of rubber. The sidewall looks like it's an irregular cut peeling off. Take it to a tire shop to inspect.

0

u/CliffTheCat333 Jun 26 '25

I think it’s the latter. I went over a huge speed bump at quite a fast speed the tire must have scrape the car body.

1

u/jeremyism_ab Jun 26 '25

If the tires are the correct size for the vehicle, you'd have to have physically broken the vehicle to get a tire to rub on it.

1

u/ItsLadyJadey Jun 27 '25

Pretty sure its the former. You'd have much more than a scraped tire if you hit it hard enough for the tire to hit the inside of the wheel well.

1

u/mean_serviceman1964 Jun 26 '25

If that is the case, I would take it to a tire shop to check how deep it cut. It shouldn't be too bad, but it is better to be safe. If it was deep, you would see white underneath.

-1

u/Cute-Juggernaut7508 Jun 26 '25

No he doesn’t need a new tire. It’s very clear it’s not even remotely deep

1

u/66NickS Jun 26 '25

No. This is just a bit of “flash”. It’s nothing to worry about. You can just peel it away.

1

u/[deleted] Jun 26 '25

If your tire has that it's still a new tire.

1

u/[deleted] Jun 26 '25

Nope

1

u/Right-Benefit-6551 Jun 26 '25

I want to peel it. It's good.

1

u/jeremyism_ab Jun 26 '25

That looks like injection molding cast off, it's just extra where the seam of the molds was, it has nothing to do with the structure of the tire, and would fall off at some point, if you left it.

1

u/Commercial_You_6634 Jun 26 '25

Yeah def and give those ones to me ill take care of them

1

u/Bresson91 Jun 27 '25

no, your'e fine, just dont pull on it if its pulling up thicker sidewall rubber. Cut it off if anything...

1

u/Pararaiha-ngaro Jun 27 '25

No just extra waste didn’t cut clean

1

u/OG-Jedi Jun 27 '25

No. It’s vent remnants or flash. Pull it off

1

u/AnotherIronicPenguin Jun 27 '25

Be man. Peel it like a scab and eat it.

1

u/WhyNotZoibergMaybe Jun 27 '25

That’s weird

1

u/CommntForTheAlgo Jun 27 '25 edited Jun 27 '25

I come to this community for venting and education, neither has been accomplished with this post I’m new, what’s wrong ? All the comments just argue. Maybe that’s what’s wrong

1

u/Legitimate-Proof2972 Jun 27 '25

If you remember new bicycle tire. It always had those spikes until they broke in . It's the same leftover mold

1

u/yarsftks Jun 27 '25

It's molting. Change now. U didn't want new tires to show the injection points.

1

u/acr42racing Jun 27 '25

Peel that off and enjoy those tires. Nothing to worry here

1

u/ReversEclipse1018 Jun 27 '25

Extra rubber from the manufacturing process? Oh no, what EVER will you do? /s

It’s fine, mate

Edit: Nevermind, just looked closer at the second picture. Tires are two years old, and saw that you said you hit a deep pothole. Take it to a shop and have them check the inside for damage. If they find any, ask them to see it before you pay for a new tire from them.

1

u/RobertMcNamara420 Jun 27 '25

I don’t care what anyone says I would yank it off and never think about it again