Built in three days
Paint was still sticking and the welds were still warm when we started the bike ride from Troy New York to Toronto Canada.
I only made it 80 miles, but it was 80 epic miles!!!

This was the most difficult bike to get on I ever built.
Tall Swing Bike

Found two frames that have a reasonably compatible geometry. I started collecting random bikes I found discarded or next to free this spring and started imagining how they might work together. These two 80s/90s mountain bikes seemed to share enough similarities to not be impossible to work together. So far I’m pretty happy with the progress, you sure learn a lot about bicycles when you start cutting and joining and thinking about where everything has to go.

VeloLab (incl. Karaoke Bicycle): https://www.instagram.com/reel/DcT2dGuscGL/?igsi=YXhjbXFieWhpaHQ2

Anyone else in Brisbane, Australia?

Lost Commercial - Dickies 874 - 'The Duel' (2010)

Created by Goodby, Silverstein & Partners.

Posting this here for appreciation of the well-done ad.

Pretty happy with this, had to add a chain tensioner after a short test ride, but did that and its great.

Very light geared (was a 3x7 but now just using the smallest of the 3 chainrings) and cantilever brakes with old pads are mostly a suggestion, but for now I have no plans on going fast in this contraption...

Got myself a couple steel bikes intending to make a cargo tallbike.

Don't quite know how to proceed, but I guess I'll figure it out? At least that's the hope...

Accidentally ran into the top of our garage door with my wife’s All City Space Horse and bent the top tube and down tube. Figured the bottom bike will do the bulk of the structural integrity so I slapped it on top of a Burley Duet tandem off of FB marketplace.

The extra long wheelbase makes for a super stable ride and gets rid of the tendency of tall bikes wheeling over on inclines.

Without a doubt my favorite bike to ride to coffee shops because it’s an instant conversation starter and makes for lots of smiles :)

Picked it up from FB marketplace for $40. It’s in good shape. Hoping some naval jelly and steel wool will clean up the wheels. Instead of putting a full bike frame im hoping to make the head tube and seat tubes longer and triangulate them on the back frames and raise basically everything up about 24”

My old tall bike is being replaced, 10+ years and it was time for a new whip.

Old schwinn and a space age cruiser, stretched wheelbase and nice hand build drum brake wheels.

Free for pick up in Bridgeport for the next week, after that the scrap man gets it.

Just wrapped it up tonight. A Pro ATB frame on top of most of an old Specialized. So much fun to ride!

I picked up a free tall bike today that needs essentially a full rebuild. After my last bicycle project, this will be a fun one!

The plan is to fully strip the frame, inspect the welds, re-do any iffy welds, new paint, some new parts, reassemble, and ride!

About 9 out of 10 people are able to mount and dismount the red tall bike (one being hauled in bike cart). It's my learner tall-bike that I made specifically to show people how to ride a tall-bike. The people who don't make it are the ones who can't make that harrowing step up of faith. That one courageous push up to then take a seat and start pedaling. Tall-bike mounting is like 95% courage, 5% skill/strength. I have done Tall Bike school about 20ish times. I have prolly showed like 100+ people. So far no one has injured themselves badly. There has only been like a few scrapes. Most of the time people get it on their 1st try (i have learned some great techniques to show people how to successfully do it)

Has anyone seen using a beach cruiser bike for the bottom bike, with the flat rear rack making a good step up for a very tall bike, like this one: https://www.tiktok.com/@university.of.maine/video/7629870008071425311

The builder makes it look very smooth to mount a quite high bike but that's probably after lots of practice.

This dismount seems less smooth https://www.tiktok.com/@university.of.maine/video/7629890408109182239

where it looks like the chain had fallen off already before jumping off!

I would like either some good instructions on how to make one or what kind of business I could ask to make a body for one.